讲义教程说明200

1、Airlines Limited03110-01航空Airlines MEDAirlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA333548_51_85培训方式354885通用类/GenericTitleGeneral Visual Inspection of Nose Landing Gear (EWIS)Mcd&Rev/厂家工卡&修订日期标题整体目视检查前起落架(EWIS)AMM 05-27-10-200-8042012-10-01A/C/飞机号Subtask No/工JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BL

2、NOAT-052710-200-804HR001001机身/AirframeAIRP00:20MP Item/MP 号Baseline/依据MP REV/ MP 版本号Sion/维修站Threshold/首检erval/重复检HA33-ZL-711-01- 1MPDZL-711-01-1,MRB32.30.00/13,MRBZL-711-01-1Ie 2 Revi6HAK1 A1 AAcs Panels/接近盖板Zones/区域Written/编写Approved/批准713 7147112012-11-262012-12-19TOOLS/工具TOOLS NESARY/必须工具ITEM项目P/

3、N件号DESCRIPTION名称EQTP类型QTY数量APP适 用性Conditions note互换信息及备注198F32204001001COLLAR, SAFETY - DOOR, NLGTO2ALL(必需/Nesary)TOOLS IF NESARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适 用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTST CORRESPOND TO THE RELATIVE WORKORDE

4、R NO.注释： 请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NESARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适 用性Conditions note互换信息及备注PARTS AND MATERIALIF NESARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适 用性Conditions note互换信息及备注IMPORTANT NOTE:he event of any discrepancies betn the Chiinstruction and the En

5、glish instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No.of Release to Service(* Tick as appropriate# Different crews should perform the work on each of the systems)Certifiest the work specified, except as otherwise specified, was carried ou

6、t in accordance with HKAR-145 and in respect tot work, The aircraft / aircraft components are considered ready for Release to Service.HKA Approval No: AI / 135 / 706 * HKE Approval No: AI /218/1215, JMM 133 * HNAT Approval No.: D.101115, JMM 047*CASL Approval No: AI / 101 / 798 * AMECO Approval No.:

7、 D.101131, JMM 001* HNAT- North West Approval No.: D.500023, JMM 049 *HAECO Approval No: DAI / 1 / 853 * SMECO Approval No.: D.400009, JMM 081* HNAT- YN Approval No.: D.4108, JMM 134 *TAECO Approval No.: DAI / 89 / 1295 * CEA Approval No.: D.200002, JMM 112 * HNAT Approval No.: D.3039, JMM 076 *ECO

8、Approval No.: D 101661, JMM 124 * CEA-Jiangsu Approval No.: D.200047, JMM 117 * SPRING Approval No.: D.200081, JMM 121 *SIAEC Approval No: AWI / 01 * STARCO Approval No.: D.200078, JMM 039* GAMECO Approval No.: D.300001, JMM 006*I Approval No.: AI / 147 / 0910 * Other: *Signature:Authorization No.:D

9、ate:*检查/Inspect 切片开始* General Visual Inspection of Nose Landing Gear (EWIS)整体目视检查前起落架(EWIS)1 .Job Set-up /开始工作TA. Get Acs /接近(1) Put an ACS PLATFORM 2M (6 FT) inition at the NLG main doors 713 and 714.起落架主门 713 和 714 放置接近工作台在位。(2) Open the nose landing-gear main-doors 713, 714 (Ref. TASK 32-22-00-01

10、0-801).打开前起落架主门 713，714(参考TASK 32-22-00-010-801)。 2 .Procedure /步骤A. Inspection /检查(1) Do a general visual inspection of the nose landing-gear (zone 711).整体目视检查前起落架（区域 711）T(2) Make suret:- There is no damage (corro, leaks or cracks) on all the parts ofthe components and the structure you can see.Al

11、l the installations (wiring) are attached correctly.确认：所有能看到的部件和结构均无损伤（腐蚀，渗漏或裂纹）。确认所有安装（线路）正确。3 .Close-up /收尾TA. Close Acs /关闭接近(1) Close the nose landing-gear main-doors. (Ref. TASK 32-22-00-410-801).关闭前起落架门(参考TASK 32-22-00-410-801)。B. Put the Aircraft back to its Initial Configuration恢复飞机到正常状态(1) Remove all the fixtures, tools, test and support equipment used during this procedure.撤掉所使用过的工具设备。(2) Make suret the work area is clean and