测长仪校准规范实验报告

PAGE13《测长仪校准规范》试验验证报告2024年03月实验用主要标准器主要标准器型号准确度等级/扩展不确定度/最大允许误差器具编号量块(0.5~90)mm二等15816量块(1~100)mm二等78036量块(125~500)mm二等77825量块(600~1000)mm二等83214标准环规φ(14~65)mmU=0.5μm(k=2)/被测仪器信息及实验条件设备型号：SJ-5100-PREC-1000出厂编号：SJGC2310108生产厂家：深圳市中图仪器股份有限公司试验地点：深圳市中图仪器股份有限公司恒温室环境温度：20.8℃相对湿度：55%RH试验日期：2023年12月12日试验人员：王晓飞、钱征宇、晏浩、常青、张鹏MPE：±(0.15μm+L/1000)试验结果示值变动性测量位置中上下前后测量结果读数值(μm)0.000.300.280.200.180.30示值误差10mm以下受校点以1mm量块对零，10mm及以上受校点直接测量。标称值(mm)修正值(μm)测得值平均值示值误差(μm)=1\*ROMANI=2\*ROMANII=3\*ROMANIII1-0.06/////1.0030.041.003021.003051.003051.003040.001.005-0.021.004981.004991.004971.004980.001.0070.041.007071.007021.007021.007040.001.0090.041.009051.009081.009011.009050.0110-0.0210.0000210.000020.0420-0.1619.9998219.99982-0.0230-0.0829.9999029.99990-0.0240-0.1039.9999739.999970.0750-0.0949.9998749.99987-0.0460-0.1059.9999659.999960.06700.2370.0001770.00017-0.0680-0.0779.9998879.99988-0.0590-0.3889.9995289.99952-0.10100-0.0299.9999099.99990-0.081500.22150.00025150.000250.032000.79200.00087200.000870.083000.06299.99992299.99992-0.14400-0.39399.99920399.99920-0.415001.14500.00074500.00074-0.406001.18600.00059600.00059-0.597001.28700.00074700.00074-0.548000.97800.00048800.00048-0.499001.02900.00114900.001140.121000-0.62999.99931999.99931-0.073、测量重复性序号测得值(μm)重复性(μm)149.99869s=0.017249.99872349.99874449.99874549.99874649.99874749.99872849.99872949.998711049.99873序号测得值(μm)极差值/c重复性sp(μm)=1\*ROMANI149.998720.0118sp=0.013249.99872349.99874=2\*ROMANII149.998740.0000249.99874349.99874=3\*ROMANIII149.998720.0059249.99872349.99871=4\*ROMANIV149.998720.0237249.99868349.99870=5\*ROMANV149.998680.0118249.99869349.998674、内尺寸示值误差直径标称值(mm)直径实际值(mm)测得值(mm)示值误差(μm)13.999714.000414.0002-0.265.000064.999664.9995-0.1实验用主要标准器主要标准器型号准确度等级/扩展不确定度/最大允许误差器具编号量块(0.5~100)mm2等60705量块(125~500)mm2等0810量块(600~1000)mm2等37432标准环规Φ(3~90)mm2等LG-15-05被测仪器信息及实验条件设备型号：ULM600-E出厂编号：1683/16生产厂家：Mahr试验地点：苏州市协兴街6号C栋210恒温室环境温度：20.1℃相对湿度：55%RH试验日期：2023年12月19日试验人员：王云祥、黄红平、吴建平MPE：±(0.085+L/1500)μm(L:mm)试验结果示值变动性测量位置中上下前后测量结果读数值(μm)0.000.120.180.190.200.20示值误差10mm以下受校点以1mm量块对零，10mm及以上受校点直接测量。标称值(mm)修正值(μm)实测值(mm)平均值(mm)示值误差(μm)=1\*ROMANI=2\*ROMANII=3\*ROMANIII10.05/////1.0030.101.003101.003091.003111.003100.001.0050.091.005091.005081.005071.00508-0.011.0070.061.007041.007051.007061.00705-0.011.0090.021.009011.009001.009021.00901-0.0110-0.059.999949.99994-0.01200.0119.9999819.99998-0.03300.0830.0000530.00005-0.03400.0740.0000240.00002-0.05500.0950.0000250.00002-0.07600.4260.0003660.00036-0.0670-0.0269.9999069.99990-0.088080.0000180.0000180.00001-0.079090.0000390.0000390.00003-0.10100100.00008100.00008100.00008-0.113、测量重复性序号测得值(mm)重复性(μm)1100.00003s=0.0132100.000033100.000014100.000025100.000016100.000027100.000008100.000009100.0000110100.000034、内尺寸示值误差直径标称值(mm)直径实际值(mm)实测值(mm)示值误差(μm)Φ27.000026.997026.9968-0.2Φ50.00049.998049.9977-0.3实验用主要标准器主要标准器型号准确度等级/扩展不确定度/最大允许误差器具编号量块(0.5~100)mm2等60705量块(125~500)mm2等0810量块(600~1000)mm2等37432标准环规Φ(3~90)mm2等LG-15-05被测仪器信息及实验条件设备型号：LABCP1000出厂编号：1475生产厂家：TRIMOS试验地点：苏州市协兴街6号C栋210恒温室环境温度：20.1℃相对湿度：55%RH试验日期：2023年12月18日试验人员：王云祥、黄红平、吴建平MPE：±(0.15+L/2000)μm(L:mm)试验结果示值变动性测量位置中上下前后测量结果读数值(μm)0.000.160.220.200.240.24示值误差10mm以下受校点以1mm量块对零，10mm及以上受校点直接测量。标称值(mm)修正值(μm)实测值(mm)平均值(mm)示值误差(μm)=1\*ROMANI=2\*ROMANII=3\*ROMANIII10.05/////1.0030.101.00311.003091.003111.003100.001.0050.091.005091.005081.0061.005090.001.0070.061.007071.007081.007061.007070.011.0090.021.009011.009031.009051.009030.0110-0.059.999969.99996-0.01200.0119.9999919.99999-0.02300.0830.0000530.00005-0.03400.0740.0000240.00002-0.05500.0950.0000550.00005-0.04600.4260.0003860.00038-0.0470-0.0269.9999369.99993-0.05800.0880.0000180.00001-0.07900.1390.0000390.00003-0.101000.1910.0001010.00010-0.092000.54200.00044200.00044-0.103000.25300.00013300.00013-0.124001.04400.00089400.00089-0.15500-0.03499.99975499.99975-0.22600-0.61599.99910599.99910-0.297000.34700.00002700.00002-0.328000.75800.00040800.00040-0.359000.49900.00016900.00016-0.331000-1.02999.99856999.99856-0.423、测量重复性序号测得值(mm)重复性(μm)1100.00005s=0.0152100.000033100.000014100.000025100.000026100.000057100.000048100.000029100.0000110100.000034、内尺寸示值误差直径标称值(mm)直径实际值(mm)实测值(mm)示值误差(μm)Φ15.00015.000615.0004-0.2Φ50.00049.998049.9978-0.2实验用主要标准器主要标准器型号准确度等级/扩展不确定度/最大允许误差器具编号量块(0.5~100)mm二等46607量块(125~500)mm二等140085标准环规φ(14~65)mmU=0.5μm(k=2)/被测仪器信息及实验条件设备型号：PLM1000-E出厂编号：1202/2023生产厂家：Mahr试验地点：无锡市计量测试院西大楼1楼实验室环境温度：20.2℃相对湿度：59%RH试验日期：2024年01月05日试验人员：王树刚、李惠、王晓飞MPE：±(0.08μm+L/1500)试验结果示值变动性测量位置中上下前后测量结果读数值(μm)0.000.020.030.020.010.03示值误差10mm以下受校点以1mm量块对零，10mm及以上受校点直接测量。标称值(mm)修正值(μm)测得值平均值示值误差(μm)=1\*ROMANI=2\*ROMANII=3\*ROMANIII1+0.04/////1.003+0.101.003121.003131.003141.003130.031.005+0.031.005061.005021.005021.005030.001.007+0.121.007131.007151.007141.007140.021.009+0.021.009021.009041.009041.009030.0110+0.0510.0000610.0000610.0000710.000060.0120+0.0720.0001120.0001320.0001220.000120.0530+0.0730.0001130.0001230.0001130.000110.0440-0.1139.9999639.9999639.9999439.999950.0650-0.1149.9999649.9999649.9999449.999950.0660-0.2659.9998159.9998459.999859.999820.0870-0.6769.9993869.9994269.9994169.999400.0780-0.1379.9999379.9999579.9999679.999950.0890-0.5189.9995989.9995989.9996189.999600.11100-0.4699.9996599.9996199.9996299.999630.09150-0.07150.00004150.00006150.00007150.000060.13200-0.21199.99989199.99992199.99991199.999910.123、测量重复性序号测得值(mm)重复性(μm)149.99996s=0.011249.99994349.99995449.99994549.99996649.99997749.99996849.99996949.999941049.99996序号测得值(mm)极差值/c重复性sp(μm)=1\*ROMANI149.999940.0059sp=0.011249.99994349.99993