航空飞行控制系统英文培训课件.ppt_第1页
航空飞行控制系统英文培训课件.ppt_第2页
航空飞行控制系统英文培训课件.ppt_第3页
航空飞行控制系统英文培训课件.ppt_第4页
航空飞行控制系统英文培训课件.ppt_第5页
已阅读5页,还剩35页未读, 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、1,FLIGHT CONTROLS - 101,2,FLIGHT CONTROLSPrimary,Theory when the right elevator goes up, the left elevator also goes up. This slide shows what happens when the pilot deflects the elevator.,12,The elevator is used to control the position of the nose of the aircraft and the angle of attack of the wing

2、. Changing the inclination of the wing to the local flight path changes the amount of lift which the wing generates. This, in turn, causes the aircraft to climb or dive. During take off the elevators are used to bring the nose of the aircraft up to begin the climb out. During a banked turn, elevator

3、 inputs can increase the lift and cause a tighter turn. That is why elevator performance is so important for fighter aircraft. preventing a loop. If the pilot reverses the elevator deflection to down, the aircraft pitches in the opposite direction.,13,The elevators work by changing the effective sha

4、pe of the airfoil of the horizontal stabilizer. As described on the shape effects slide, changing the angle of deflection at the rear of an airfoil changes the amount of lift generated by the foil. With greater downward deflection of the trailing edge, lift increases. With greater upward deflection

5、of the trailing edge, lift decreases and can even become negative as shown on this slide. The lift force (F) is applied at center of pressure of the horizontal stabilzer which is some distance (L) from the aircraft center of gravity. This creates a torque T = F * L on the aircraft and the aircraft r

6、otates about its center of gravity. The pilot can use this ability to make the airplane loop. Or, since many aircraft loop naturally, the deflection can be used to trim or balance the aircraft, thus,14,FLIGHT CONTROLSTypes of Control Devices,THE STABALATOR,15,STABALATOR,Sometimes the fixed stabilize

7、r and separate movable elevators are replaced by a single moving horizontal tail known as a Stabilator.,16,FLIGHT CONTROLSTypes of Control Devices,THE RUDDER,17,At the rear of the fuselage of most aircraft one finds a vertical stabilizer and a rudder. The stabilizer is a fixed wing section whose job

8、 is to provide stability for the aircraft, to keep it flying straight. The vertical stabilizer prevents side-to-side, or yawing, motion of the aircraft nose. The rudder is the small moving section at the rear of the stabilizer that is attached to the fixed sections by hinges. Because the rudder move

9、s, it varies the amount of force generated by the tail surface and is used to generate and control the yawing motion of the aircraft. This slide shows what happens when the pilot deflects the rudder, a hinged section at the rear of the vertical stabilizer.,THE RUDDER,18,THE RUDDER,19,FLIGHT CONTROLS

10、Types of Control Devices,THE RUDDEREVATOR,20,The V-Tail concept is based upon the removal of the vertical stabilizers drag and weight and combining its function into the horizontal stabilizer.,THE RUDDEREVATOR,21,FLIGHT CONTROLSTypes of Control Devices,THE AILERON,22,Ailerons can be used to generate

11、 a rolling motion for an aircraft. Ailerons are small hinged sections on the outboard portion of a wing. Ailerons usually work in opposition: as the right aileron is deflected upward, the left is deflected downward, and vice versa. This slide shows what happens when the pilot deflects the right aile

12、ron upwards and the left aileron downwards. The ailerons are used to bank the aircraft; to cause one wing tip to move up and the other wing tip to move down. The banking creates an unbalanced side force component of the large wing lift force which causes the aircrafts flight path to curve. (Airplane

13、s turn because of banking created by the ailerons, not because of a rudder input.,THE AILERON,23,The ailerons work by changing the effective shape of the airfoil of the outer portion of the wing. As described on the shape effects slide, changing the angle of deflection at the rear of an airfoil will

14、 change the amount of lift generated by the foil. With greater downward deflection, the lift will increase in the upward direction. Notice on this slide that the aileron on the left wing, as viewed from the rear of the aircraft, is deflected down. The aileron on the right wing is deflected up. There

15、fore, the lift on the left wing is increased, while the lift on the right wing is decreased. For both wings, the lift force (Fr or Fl) of the wing section through the aileron is applied at the aerodynamic center of the section which is some distance (L) from the aircraft center of gravity.,THE AILER

16、ON,24,This creates a torque about the center of gravity. If the forces (and distances) are equal there is no net torque on the aircraft. But if the forces are unequal, there is a net torque and the aircraft rotates about its center of gravity. For the conditions shown in the figure, the resulting mo

17、tion will roll the aircraft to the right (clockwise) as viewed from the rear. If the pilot reverses the aileron deflections (right aileron down, left aileron up) the aircraft will roll in the opposite direction. We have chosen to name the left wing and right wing based on a view from the back of the

18、 aircraft towards the nose, because that is the direction in which the pilot is looking.,THE AILERON,25,THE AILERON,26,FLIGHT CONTROLSTypes of Control Devices,THE FLAPS,27,The amount of lift generated by a wing depends on the shape of the airfoil, the wing area, and the aircraft velocity. During tak

19、eoff and landing the airplanes velocity is relatively low. To keep the lift high (to avoid objects on the ground!), airplane designers try to increase the wing area and change the airfoil shape by putting some moving parts on the wings leading and trailing edges. The part on the leading edge is call

20、ed a slat, while the part on the trailing edge is called a flap. The flaps and slats move along metal tracks built into the wings. Moving the flaps aft (toward the tail) and the slats forward increases the wing area. Pivoting the leading edge of the slat and the trailing edge of the flap downward in

21、creases the effective camber of the airfoil, which increases the lift. In addition, the large aft-projected area of the flap increases the drag of the aircraft. This helps the airplane slow down for landing.,THE FLAPS,28,THE FLAPS,29,THE FLAPS - types,30,THE FLAPS - plain,Flaps Hinged surfaces attac

22、hed to the trailing edge of a wing, either to increase maneuverability or to increase lift at the expense of drag The simplest is the plain flap shown below:,31,THE FLAPS - split,Split flaps are not very common any more. They can be found on many twin Cessna and DC-3s. The main advantage of split flaps is that they are very structurally strong and as a result can be extended at high speeds.,32,THE FLAPS - fowler,Fowler flaps are the most commonly used flaps on light aircraft. The Fowler flap moves back as it extends. Therefore,

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论