翻译.pdf_第1页
翻译.pdf_第2页
翻译.pdf_第3页
翻译.pdf_第4页
翻译.pdf_第5页
已阅读5页,还剩9页未读, 继续免费阅读

翻译.pdf.pdf 免费下载

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、Materials Science and Engineering A280 (2000) 233246 Process modelling of grain selection during the solidifi cation of single crystal superalloy castings P. Carter, D.C. Cox, C.A. Gandin 1, R.C. Reed * Department of Materials Science and Metallurgy, Uni6ersity of Cambridge/Rolls-Royce Uni6ersity Te

2、chnology Centre, Pembroke Street, Cambridge CB2 3QZ, UK Received 23 July 1999; received in revised form 11 October 1999 Abstract A process model is described for the grain selection occurring during the solidifi cation of single crystal investment castings, which are now used widely for a number of

3、critical applications in gas turbine engines. The basis of the model is a thermal analysis of the heat transfer in the vicinity of the chill region onto which the molten metal is poured. Subsequently the competitive growth of grains during directional solidifi cation is simulated via a cellular-auto

4、maton technique. For the purpose of model validation, processing trials have been carried out on a commercial single crystal casting furnace. The thermal cycles set up in and around the vicinity of the grain selector have been measured, and these are used to choose a number of critical parameters in

5、 the thermal model. The evolution of grain structure during competitive growth has been characterised using a number of analytical techniques, including orientation imaging microscopy. The results are compared critically with the predictions from the model. It is shown that the model is able to repr

6、oduce the statistical distribution describing the fi nal casting orientation, measured with respect to the ?001? crystallographic pole. The model is used to study the geometrical factors infl uencing competitive growth and the effi cacy of two designs of grain selector, and in particular the conferr

7、al of any control of the secondary ?001? Keywords: Nickel-base superalloy; Single crystal; Solidifi cation; Processing; Modelling 1. Introduction It is well known that investment casting 1 is used routinely nowadays for the fabrication of nickel super- alloy 2,3 single crystal turbine blading of ver

8、y complex geometries 47 with intricate channels often incorpo- rated so that cooler air can be forced to fl ow within and along the blades during operation 8,9. Such develop- ments have, over the past 20 years or so, contributed signifi cantly to a steady increase in the turbine entry temperatures o

9、f modern aero-engines 10; the rate of approximately 5 K per year averaged over the past two decades shows no sign of slowing. Less well known is that the single crystal properties along ?001?, which is chosen during the grain selection process since it is the preferred growth direction, are usually

10、favourable com- pared to those along ?001? or ?111? This is fortuitous. Had this not been the case, it is unlikely that single crystal turbine blades would have found such wide- spread application. However, despite the preference for perfect alignment along ?001?, single crystal turbine blades are o

11、ften employed in a condition that has the centrifugal load- ing away from this exact orientation, perhaps by up to 15 11. Practical considerations and cost implications necessitate that this is the case, and for this reason a trade-off between orientation and performance must always be made. This si

12、tuation demands that proper attention be paid to the factors infl uencing the orienta- tion of the blading conferred during casting and the grain selection process in particular. This is one of the aims of the present paper. A process model is described, * Corresponding author. Tel.: +44-1223-334320

13、; fax: +44-1223- 334567. E-mail address:rcr10cus.cam.ac.uk (R.C. Reed) 1On leave from Department des Materiaux, Laboratooire de Metallurgie Physique, Ecole Polytechnique Federale de Lausanne, Switzerland. Present address: Laboratoire de Science at Genie des Materiaux Metalliques, Ecole des Mines de

14、Nancy, Parc de Saurupt, F-54042 Nancy, Cedex, France. P. Carter et al./Materials Science and Engineering A280 (2000) 233246234 which is based upon a thermal analysis of the heat transfer occurring in a commercial casting furnace, and a cellular-automaton model for competitive den- drite growth 12,13

15、. For the purposes of model vali- dation, a number of castings have been instrumented and characterised via several analytical techniques. Particular attention is paid to the choice of parame- ters which are required as input into the model. The model is used to study the geometrical factors infl u-

16、 encing competitive growth and the effi cacy of two common designs of grain selector. 2. Background Since the possibility of casting a component into single crystal form depends directly upon the competi- tive growth of dendrites, it is worth examining briefl y the reasons why the effect arises in t

17、he fi rst place. It is well known 14 that the dendrite tip growth rate 6 depends upon the local tip under-cooling DTtipbe- low the equilibrium liquidus temperature. In the gen- eralcasethereareanumberofeffectswhich contribute to the extent of under-cooking 15, for example thermal diffusion 16, inter

18、face attachment kinetics 17 and surface capillarity 18. However, for dendritic growth occurring far from the limit of con- stitutional super-cooling, the contributions made by these effects are small and the rate of dendrite growth is controlled by the rate of solute diffusion alone 14,19. In these

19、circumstances, one plausible model is that proposed by Burden and Hunt 20 a number of years ago, in which the dendrite growth velocity 6 increases monotonically with the square of the under- cooking DTtip, i.e. 68DTtip 2 . Thus, dendrites which are misaligned with respect to the maximum gradient of

20、the temperature fi eld must grow at a speed which is faster than those which are less well-aligned, and hence further behind the growth front. This effect al- lows the well-aligned grains to pinch-off the less-well aligned grains, for example through the growth of secondary and then tertiary side ar

21、ms 21 as depicted in Fig. 1 19. This is the picture of competitive growth fi rst proposed by Walton and Chalmers 22. Subsequently, the models for dendrite tip kinetics have been refi ned, for example by Kurz, Giovanola and Trivedi 23. Here, DTtipdepends upon the tem- perature gradient G, the velocit

22、y 6, the mean compo- sition Co, the slope of the liquidus mLand the partitioning coeffi cient k. However, as formulated the model applies to binary alloys and the extension of the theory to cover multicomponent systems, which are usually those of the most practical interest, has not yet been carried

23、 out in a rigorous sense. To cir- cumvent this diffi culty Bobadilla et al. 24 have em- ployed pseudo-binary values Co, mLand k which are defi ned according to Co=% i CoimL= %imLiCoi mLCo k= %imLiCoiki mLCo (1) where the partitioning coeffi cients kiand liquidus slopes mLimust be estimated from the

24、binary phase diagrams. However, although this extension is a rea- sonable working hypothesis it must be regarded as phenomenological. A particular diffi culty is the lack of any realistic treatment of the interaction between the solute concentration fi elds from neighbouring den- dritetipswhicharesl

25、ightlymisaligned,although some progress with regard to this has recently been made 25,26. In principle the phase fi eld method 27,28 is able to treat this phenomenon. In the present paper the stochastic treatment of the competitive growth of dendrite envelopes will be em- ployed, as developed recent

26、ly by Gandin and Rappaz et al. 12,13,19. It is notable that this model is able to account for the local curvature of the growth front. However, this and the above considerations in- dicate that any prediction of the evolution of mi- crostructure will only be as accurate as the thermal model on which

27、 it relies. For this reason, consider- able effort has been made to build a realistic thermal model for the heat transfer occurring in a commercial single crystal casting furnace 29. Since the concern here is primarily with the grain selection process, par- ticular emphasis has been placed on ensuri

28、ng that the thermal description of the furnace is accurate in the vicinity of the grain selector. Fig. 1. Schematic representation of dendritic growth illustrating the nature of the competitive growth process and the pinching-off of less favourably orientated grains. After 19. P. Carter et al./Mater

29、ials Science and Engineering A280 (2000) 233246235 Fig. 2. Schematic diagram of the furnace chamber, identifying the positions of the shell mould, copper chill, graphite heating element and baffl es. shields and which therefore keep the heat fl ux more-or- less perpendicular to the direction of with

30、drawal; thus an effectively planar solidliquid interface is main- tained as directional solidifi cation occurs away from the chill region. After a pause to allow for complete fi lling to occur, the mould was withdrawn rather rapidly until that the starter and selector were clear of the water- cooled

31、 baffl e; during the present experiments a with- drawal rate of 0.06 mm s1was maintained thereafter. 3.2. Design of moulds Wax replicas consisting of a feed arrangement, platen, starter, selector, and test bar sections were assembled. The test bars were rectilinear (of dimensions 1212165 mm3) and th

32、ese were mounted on double helical grain selectors (6 mm diameter with a 30 pitch, total height of 45 mm) which were in turn placed above cylindrical starter blocks (25 mm height and 20 mm diameter). A single casting consisted of eight such test bars arranged on a circular carousel, see Fig. 3. This

33、 was bottom fed via a central riser which was connected to the starter blocks by a series of horizontal runners, as in 30. Four castings were made, yielding 32 bars in total. The models were then coated with multiple layers of ceramic slurry (:80% alumina and 20% silica) to obtain a shell a few mm i

34、n thickness. After coating and drying, the wax was removed in a steam autoclave. The green moulds were then fi red to remove the remaining wax and to strengthen the ceramic shell by partial sintering. 3.3. Instrumentation of the furnace and moulds Several modifi cations were made to the furnace to a

35、llow for extra instrumentation in the vicinity of the copper chill, specifi cally for the purpose of model vali- dation. A vacuum port was installed on the ram, be- neath the copper chill, which allowed up to ten thermocouples to be placed in the mould. Furthermore, a hole for a thermocouple was dri

36、lled radially in the copper chill at half thickness. Locations for the thermocouples were created by placing plastic inserts in the wax replicas. These were removed during fi ring leaving holes in the fi nal shell. After the mould had been positioned on the chill plate, type B thermocouples were pos

37、itioned within the mould; these were retained in recrystallised alumina sheaths which provided protection from the molten 3. Experimental details 3.1. Details of the casting procedure employed A fully instrumental industrial directional casting furnace (Rolls-Royce Company Research and Develop- ment

38、 Foundry, Bristol, UK) was used for the present study. Only brief details of this will be given here; for a more complete description of the furnace design the reader is referred to 29. Essentially, it consists of a central furnace chamber arranged below a vacuum induction melting unit and above a w

39、ithdrawal cham- ber, see Fig. 2. Prior to casting, all three chambers are evacuated to a partial pressure of approximately 103 bar and the moulds raised into the furnace chamber, which is pre-heated to above the melting point of the charge using graphite resistance elements. The whole assembly is th

40、en allowed to equilibrate for a number of hours prior to casting. The second generation single crystal alloy CMSX-4 was used for the present study, the chemical composi- tion of which is given in Table 1. After induction melting in the upper chamber, the charge was poured at a temperature of 1500C i

41、nto a shell mould which was mounted on a water cooled copper chill in the centre of the furnace chamber. In the present arrangement ther- mal isolation of the withdrawal chamber is achieved by a series of water cooled baffl es, which serve as radiation Table 1 Chemical composition of CMSX-4 WTiTaReN

42、iMoHfCrCoAl Balance0.70.096.49.55.7wt%6.41.086.52.92 P. Carter et al./Materials Science and Engineering A280 (2000) 233246236 Fig. 3. Photograph of the wax assembly prior to coating with the ceramic slurry. The running system can be seen clearly. alloy and acted as effective seals against metal loss

43、. The thermocouples were joined to an instrumentation loom and then to data logging equipment via the vacuum plate in the ram. The thermocouple extensions and the instrumentation loom were protected during casting by several layers of ceramic blanket, see Fig. 4. During casting, the temperatures wit

44、hin the copper chill were recorded, as they were at one position in each of the eight starter blocks making up one carousel; by doing this it was hoped to minimise the loss of heat to the thermocouples. The thermocouple positions are de- picted in Fig. 5. During casting data were logged at 0.01 s in

45、tervals using two computers equipped with commercial data capture software. Electrical noise in the thermocouple signals was reduced using a 4 MHz low-pass fi lter and shielded thermocouple extension cables. 3.4. Microstructural analysis of the castings After casting, the orientation of each test pi

46、ece was determined by the automatic indexing of back Laue patterns using the SCORPIO method, which is re- viewed in 29. For each casting, three independent SCORPIO measurements were made. Fig. 4. Photograph of instrumented mould prior to casting; the furnace can be seen in the background. P. Carter

47、et al./Materials Science and Engineering A280 (2000) 233246237 Fig. 5. Illustration of the positions of the thermocouples, with respect to the copper chill, starter block and grain selector. 4. Heat transfer in the starter block: modelling and measurements A thorough description of the heat transfer

48、 occurring during the process would require the simulation of 1. the soaking of the furnace chamber as an equi- librium temperature distribution is attained, 2. the melting/mould fi lling and fi nally 3. the withdrawal of the mould assembly past the baffl es. However, this represents a signifi cant

49、challenge even with existing computer resources and some simplifying assumptions are required. During soaking of the mould and furnace, heat transfer is dominated by radiation from the furnace heating element and conduction through the mould and furnace lining; convective heat transfer is of course

50、signifi cant during melting/pouring but less so during withdrawal, since the ram is held in position for some time to allow the liquid to stabilise. Therefore, in the current model, mould fi lling has not been considered. The soaking and withdrawal processes were modelled with a three-dimensional, f

51、i nite element analysis using the ProCAST software (UES, OH, USA) with tempera- ture/time boundary conditions and temperature depen- dent materials properties. During soaking the molten alloy is held adiabatically in the mould cavity at the pouring temperature, with the mould kept in the fully raise

52、d position. The mould was then allowed to come to equilibrium with the furnace walls and graphite resistance elements; consistent with measurements made using optical pyrometry the latter was prescribed a temperature 1515C. Once equilibrium had been at- tained, the adiabatic boundary condition was r

53、emoved and replaced with realistic interface heat transfer coeffi - cients and surface properties. The choice of these parameters is discussed in the next section. The ram assembly was then withdrawn from the furnace at the predetermined rate. This necessitated the use of radia- tion view factors 34

54、 to account for variations in the mould cross-section. 4.1. Details and construction of geometry For modelling purposes, an axisymmetric section in- corporating a single test bar, is considered to be a suffi ciently accurate geometrical representation of the furnace. The geometries of the components

55、 were cre- ated individually using purpose built software tools 35,36 in the following way. First, the mould was created by extracting the major surfaces of the casting which then formed the inner surface of the mould. After surface meshing, this was then offset by an amount equal to the mould thick

56、ness, to obtain a mesh of the outer surface of the mould. These surface meshes were then combined with those of the chill and ram, The microstructures observed in the starter blocks were characterised on both horizontal and vertical sec- tions. Prior to analysis, the surfaces of each section were gr

57、ound and polished to a 1 mm fi nish, and then polished for a further 20 min with colloidal silica. Grain sizes and texture distributions were then determined using TSL OIM software 31 installed on a JEOL 5800LV scanning electron microscope (SEM). Electron- back-scattered diffraction patterns (EBSDs)

58、 were col- lectedusingregularsquaregridsof1050mm edge-length, over the whole of the prepared sections. On horizontal sections, typically 3000 patterns were taken, while on vertical sections some 60000 patterns were collected; these were subsequently indexed and grain boundaries determined using the

59、methods re- ported in 32,33. The grain size/density relationships determined in this way were compared with those ob- tained using traditional optical metallography. P. Carter et al./Materials Science and Engineering A280 (2000) 233246238 and a solid tetrahedral mesh created in the enclosed volume. A solid mesh of the furnace was then created by sweeping its two-dimensional axisymmetrical de- scription through an appropriate angle, which in this case was 45. Finally, the models of the moving assem- bly and furnace were combined. The meshes describing the furnace and casting are illustrate

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论