proceeding of fourteenth abaqus user group2001p02_W_第1页
proceeding of fourteenth abaqus user group2001p02_W_第2页
proceeding of fourteenth abaqus user group2001p02_W_第3页
proceeding of fourteenth abaqus user group2001p02_W_第4页
proceeding of fourteenth abaqus user group2001p02_W_第5页
已阅读5页,还剩9页未读, 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、SIMULATION OF ANNULAR CORRUGATED SHEATH MANUFACTURE AND MECHANICAL BEHAVIOUR USING ABAQUS EXPLICIT/STANDARDJonathan Roy Stephen M KingBICCGeneral, Supertension and Subsea SystemsSUMMARYAn integral part of the design of many high voltage supertension cables is an extruded aluminium sheath that perfor

2、ms several important functions. It provides mechanical protection for the insulation as well as providing a path for fault currents. It acts as a moisture barrier in the case of polythene insulated cables and as an oil containment system for fluid filled cables. It also enables the cable to be insta

3、lled without damage due to its predictable bending performance. To achieve the latter, the aluminium tube is corrugated after extrusion and in the case of polythene insulated cables, it is important that the corrugations are annular. This is done by a cleverly designed thread that rotates around the

4、 sheath as the cable moves through the corrugating head. If the corrugations are too severe, metal is wasted and the chance of overworking the material arises. If the corrugations are shallow, it increases the stiffness of the cable and risks the onset of buckling.This paper describes the use of ABA

5、QUS Explicit in modelling the corrugation process and the use of ABAQUS Standard to assess the sensitivity of the sheath design to changes in the basic parameters that describe the form of the corrugations.1. SIMULATION OF CORRUGATION PROCESSHigh voltage power cables often have a metal sheath, for b

6、oth mechanical and electrical purposes. One metal often used in making these sheaths is aluminium, as it exhibits the required electrical properties. However, a straight aluminium tube is too rigid. A cable is often transported on a circular drum and therefore has to be capable of being bent around

7、this drum. If the sheath is corrugated, then it becomes less rigid and can be bent around the drum without fear of buckling. Both annularP02/14and spiral corrugations can be created, but this paper concentrates on annular corrugations. BICCGeneral has a machine which creates an annular corrugated sh

8、eath (figure 1).igure 1 The annular corrugating machine at BICCGeneral, Erith. The sheath moves from right to left.1.1 What Actually Happens?The aluminium tube is corrugated by a spiral nut (see figure 2), which is rotated around the tube to create an annular corrugation.Figure 2 An example of a spi

9、ral nut used to create the corrugationsAs the aluminium tube passes through the nut, the central axis of the nut rotates around the central axis of the tube. This forces the thread of the nut into the aluminium tube and as it moves in a circular pattern creates the annular corrugations. It should be

10、 noted that the nut does not rotate on its own axis, but it is offset at an angle in the vertical plane (see figure 3). This creates a swash plate effect which keeps the thread at right angles to the tube axis as it is moved around the tube.Figure 3 The aluminium tube passing through the angled nutT

11、he shape of the nut, the vertical offset angle, the speed of the tube through the nut, the dimensions of the original tube and the speed at which the nut rotates around the tube are all factors in the final shape of the corrugations. The pitch (distance from crest to crest), the rib height (distance

12、 vertically from crest to trough), the thickness and the diameter of the corrugated tube can all be controlled by the input parameters.In order to understand the process more fully, to find out what parameters need to be changed to give a sheath or the required dimensions and in an effort to reduce

13、the amount of aluminium used (and hence to reduce cost), the process was modelled using ABAQUS Explicit. The first step was to build a model of the actual corrugation process.1.2 Building the ModelThe undeformed aluminium tube was modelled using shell elements, and the corrugating nut was represente

14、d using rigid elements. The tube is guided towards the corrugating nut by a guide bush. This limits the radial movement of the tube as it is corrugated (see figure 4). The bush was represented by rigid surfaces.Figure 4 The tube passing through the guide bush before beingThus the basic model is read

15、y for the analysis.1.3 Boundary ConditionsThe boundary conditions on the model are crucial to representing the corrugation process. To apply them correctly, the motion of the corrugating nut must be understood. The nut is angled away from the approaching tube in the vertical plane. It then rotates o

16、n an axis parallel to the central axis of the tube, reaching the correct radius by spiralling out from a central position (this means that the first few corrugations are not well defined, which can be seen in figure 1). The tube moves in the direction of its central axis, through the guide bush and

17、the nut. The tube can move in the cross sectional plane of the tube, but this movement is restricted by the guide bush. The speed of the tube is a factor in the pitch of the corrugations, the shape of the thread is a factor in the rib height and thickness of the corrugations and the initial size of

18、the tube contributes to the diameter and thickness of the final CSA sheath dimensions.1.4 Loading ConditionsThe loading conditions take the form of translational and rotational displacements and velocities. The tube itself was accelerated up to a constant speed which was sufficient to move it throug

19、h the die along its entire length. The motion of the nut was synchronised with the tube for its eccentric behaviour. This was specified as a series of translational displacements following a spiral pattern to enable the nut the have a gradual lead in to the corrugation process. The nut movement due

20、to the rotational movement of the carriage was specified using orthogonal angular velocities.1.5 Analysis DetailsThe speed of the process in reality is quite slow with the tube moving at about0.6 metres/min. For the analysis to proceed in a reasonable time frame the speed of the tube was set to appr

21、oximately 5 metres/sec. This speed was chosen so as not to introduce unwanted inertia effects into the system whist still giving results comparable to lower speed analyses. A certain amount of mass scaling was also used. Even so, the typical elapsed time for an analysis on an SG Octane was about 12

22、hrs.The displaced shape of the tube is shown about half way through the simulation in figure 4 and at the end of the simulation in figure 5. As with all explicit analyses of this type a check should always be made on the validity of the result by examining how the energy has been distributed. Figure

23、 6 shows the various energy values throughout the analysis showing that by far the majority of the energy has been absorbed in plastic deformation of the material with a relatively small amount of kinetic and frictional dissipation energy. This indicates that inertia effects are successfully being r

24、emoved from the problem.Figure 5 A corrugated tube at the end of an analysisFigure 6 Energy plot for corrugation analysisAnalysis ResultsOne result of the analysis is shown in figure 7 and this is just a sample of the many results that can be produced. In common with many computer simulations, the a

25、nalysis tends to show an ideal set of results, but having established the analysis methodology, modifications can be made to a whole range of parameters in order to understand cause and effects and ultimately to provide valuable information that can be used in a production environment.The main drawb

26、ack of this type of analysis is the length of time required to reach a solution. Care must be taken in not trying to run the analysis too quickly. However, providing this is done properly, convergence is not a problem and the explicit method can achieve results not available in any other way. Presen

27、tly, the usefulness of this technique is only limited by computer processingpower.2. SIMULATION OF SHEATH BENDING PROCESSAfter the (now corrugated) sheath exits the corrugating machine, the cable is wound onto a cable drum. This creates stress in the sheath, with some of it in compression and some o

28、f it in tension. ABAQUS Standard can be used to analyse this. The idea was to create a simple model and solution process that could be used quickly and efficiently for any sheath specification required. The model building process was automated using IDEAS and a FORTRAN program. Initially the modelli

29、ng of the bending was performed on a new unstressed model, and later theFigure 7 Contours of equivalent plastic strainresults from the corrugation process (in section 1) were used as initial conditions for the bending, thus taking account of the fact that the sheath is already deformed and stressed.

30、2.1 General Form of a CSA SheathThe theoretical shape of a BICCGeneral CSA sheath is a sinusoidal curve. The pitch, rib height and diameter (over the trough, say) provide enough information to create a unique sine curve with a radius around a central axis. The other relevant dimension is the thickne

31、ss of the sheath. These four dimensions provide enough information to create a model of an annular corrugated sheath.2.2 Modelling TechniquesTwo different models were considered. The first used solid elements to give the sheath its thickness, and the second used shell elements with the thickness pro

32、vided on the *SHELL SECTION keyword. In reality, the sheath shape is not sinusoidal, and the two models approximate the shape in slightly different ways. The solid model was based on two sinusoidal curves, separated radially by the required sheath thickness and revolved around the required centrelin

33、e. This means that the sheath has the desired thickness at the trough and at the crest but between these positions the sheath is thinner. The shell model is based on a sinusoidal curve at the centre of the sheath thickness and revolved around the centreline. The required thickness is given in the sh

34、ell section input and thus the shell model has a constant sheath thickness. Thus the shell model contains more material and is slightly stiffer than the solid model. This was borne out by results.Constant thicknessVariable thicknessFigure 8 Illustration of difference in thickness of each model (the

35、top curve is the shell model)2.3 Test CaseBoth models were tested using a set of dimensions for an actual 230 kV cable.The dimensions used were:Pitch:32.0 mmNominal thickness:3.4 mm Rib height:6.5 mm Diameter over trough: 124.6 mmThe length of the sheath examined was 320.0 mm, i.e. 10 pitch lengths.

36、 Finally, the bending radius used ranged from infinity (straight cable) to 2.8 m, which represented the radius of the drum on to which the cable is wound after exiting the corrugator.2.4 Shell ModelThe shell model was created by drawing a sinusoidal curve based on the above dimensions and rotating i

37、t around the central axis to create a corrugated surface. The sine curve created was through the centre of the thickness of the sheath. This surface was then meshed. The shell elements used in this model were S8R elements, 8 noded, 2nd order elements. Due to the symmetry of the model only 180 of the

38、 sheath was modelled. The sheath was given a constant thickness of 3.4 mm. The mesh density used to cover the surface was 120 elements along by 10 elements around.2.5 Solid ModelThe solid model was created using two sinusoidal curves separated on the vertical axis by 3.4 mm, one at the outer edge of

39、 the sheath, the other at the inner edge.These curves were joined and rotated around the central axis to create a corrugated solid. As outlined above, this sheath did not have constant thickness. The maximum thickness was 3.4 mm and the minimum thickness was about 2.8 mm, which falls within the shea

40、th specification minimum. Again, due to symmetry, only 180 of the sheath was modelled. Solid C3D20R elements were used for this analysis. These are 20 noded, 2nd order brick elements. The mesh density used to fill the solid part was 60 elements along by 10 elements around with 3 elements through the

41、 thickness of the sheath.Figure 9 A comparison of the shell and solid mesh using the test dimensions for a standard CSA2.6 Material PropertiesMaterial property information came from the Aluminium Federation property tables. The properties used for the analyses were for 99.99% pure aluminium. Basic d

42、ata:Youngs Modulus:69.09E+09 N/m2Poissons Ratio:0.340.2% Proof Stress:25.0E+06 N/m2 UTS:58.0E+06 N/m2The material properties were specified as true strain and true stress quantities as required for non-linear analysis in ABAQUS.2.7 Boundary ConditionsOne symmetric half of a sheath was modelled with

43、appropriate boundary conditions on the symmetry nodes.Sheath bending was achieved by applying rotations to reference nodes located on the central axis of the sheath at either end of the model. These nodes were connected to the nodes at the end of the sheath by a) a rigid surface in the case of the s

44、olid model and b) by a kinematic constraint in the case of the shell model. By applying equal and opposite rotations at each of the reference nodes and by allowing the sheath to translate freely at one end, a pure bending condition was achieved.2.8 ResultsBoth models were analysed and the results ar

45、e shown here. As expected the solid model took longer to run. There are 9777 nodes in the solid model compared with 3861 in the shell model, resulting in this time difference. The shell model was about twice as fast as the solid model, taking about 25 minutes to run to completion.The results from th

46、e two different analyses are summarised here:ModelViewQuantityMaximum ValueShellInner sheathVon Mises5.7e+07 N/m2SolidInner sheathVon Mises5.3e+07 N/m2ShellInner sheathEquivalent plastic strain5.7e-02SolidInner sheathEquivalent plastic strain5.3e-02ShellOuter sheathEquivalent plastic strain7.4e-02So

47、lidOuter sheathEquivalent plastic strain5.3e-02ShellN/ABending moment307 NmSolidN/ABending moment296 NmTable 1 Summary of resultsIn column 2 inner sheath represents the inside surface of the sheath and outer surface represents the exterior surface.The results from both cases show an increase in bend

48、ing stiffness as the bending radius decreases. There is little change in the bending stiffness at large radii, but it increases rapidly as the radius goes below 20m. The results also show that the bending moment increases linearly, from approximately 170Nm at a radius of 110m, to 270Nm at a radius o

49、f 20m. The increase is then more rapid, finishing at approximately 307Nm at a bending radius of 2.8m.2.9 DiscussionThe work reported here shows that the bending behaviour of a symmetrical, annular corrugated sheath can be modelled either by using a standard shell or solid finite element model. Both

50、models were based on a standard sine curve profile and were bent from an initially unstressed state. The inherent differences in the element formulations and the subtle changes in geometry caused by the different modelling techniques meant that identical results could not be obtained from the two mo

51、dels. The maximum bending moments are similar however with only a 3.7% difference at the minimum bending radius of 2.8m. It should be remembered that this maximum bending moment occurs after considerable plastic deformation has taken place. In fact the bending moments are near identical during the e

52、lastic part of the bending. (The elastic state only lasts a short time before plastic behaviour begins to occur)Overall the results from the two models are comparable and although the solid element model is probably slightly more accurate, the analysis time is over twice that for the shell model.The

53、 procedure developed to model the bending behaviour of annular CSA sheath using ABAQUS (in conjunction with IDEAS) is efficient and the next section describes its use in a sensitivity study of the main geometric features of thesheath.3. SENSITIVITY STUDY OF SHEATH BENDING PROCESSUtilising the bendin

54、g method outlined in section 2, a sensitivity study was undertaken to examine the effects on the bending performance of the sheath by varying certain key dimensions. The study was based on the same sheath design used in section 2 and three key dimensions were varied. The shell model of the previous

55、section was used to analyse sheaths with several different rib heights, pitches and thicknesses. The sensitivity study was then carried out to help indicate how the amount of material in a sheath may be optimised.3.1 ProcedureThe study was based around the sheath dimensions used in the previous sect

56、ion, namely:Pitch:32.0 mmNominal thickness:3.4 mm Rib height:6.5 mm Diameter over trough: 124.6 mmThe internal diameter of the trough was held constant throughout the entire study, whilst each of the thickness, rib height and pitch were varied in turn. The dimensions were varied over the following r

57、anges:Pitch:20 mm - 50 mm in 2 mm stepsThickness:2.0 mm - 5.0 mm in 0.2 mm stepsRib height:3.0 mm - 10.0 mm in 0.5 mm stepsOnly one dimension was varied at a time so that, for example, the thickness would vary from 2.0mm to 5.0mm while all other dimensions would be kept in the existing configuration.The weight per kilogram of each configuration (based on nominal dimensions) was also calculated. In addition, calculations were made to asses the ovality of the sheath as it was bent, i.e. how much it varied from being circular. The analyses simulated pure bending of ra

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

最新文档

评论

0/150

提交评论