ld141216n020 report_safety

1、Test Report No: LD141216N020TEST REPORTNo. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 1 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dong

2、guan BranchTo:SPA CONDOR ELECTRONICSAddress:Zone dActivits Route de MSila Ilot 70 section 161 Bordj Bou Arreridj 34000Factory name:SPA CONDOR ELECTRONICSLocation:Zone dActivits Route de MSila Ilot 70 section 161 Bordj Bou Arreridj 34000Standards used:EN 60950-1: 2006+ A1: 2010 + A11: 2009+ A12: 2011

3、IEC 60950-1: 2005+ A1: 2009Start date:Dec. 16, 2014Finish date:Dec. 16, 2014Sample No:N141122-003-001-001Sections examined:All clausesRe-testing:-Mobile Phone, Model: PGN-506Remark / Note:NoneCONCLUSION: The sample satisfies to the clauses examined.Test done by Bin He Engineer / Safety DepartmentApp

4、roved by Kim Li Supervisor / Safety DepartmentDate: Dec. 16, 2014Date: Dec. 16, 2014This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report

5、 sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and ex

6、pressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such

7、 notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless spe

8、cific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specificationTest Report No: LD141216N020History of Remark-NoteNo. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 2 of 7

9、7Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchClauseN/APicture of the problemDescription of the problem:N/AN/AN/AModification result:N/AClauseN/APicture of the problemDescript

10、ion of the problem:N/AN/AN/AModification result:N/ATest Report No: LD141216N020Open ViewNo. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 3 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60

11、950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchTest Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 4 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60

12、950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchTest Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 5 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60

13、950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchTest item descriptionMobile PhoneTrade Mark .ManufacturerSPA CONDOR ELECTRONICSModel/Type reference.PGN-506 RatingsFor equipment: 5Vdc, 1AFor adaptor input: 100-240Vac, 50/60Hz; output: 5Vdc, 1ACopy of marking plate:Test Report No: LD141216

14、N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 6 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchPossible test case verdi

15、cts:- test case does not apply to the test objectN/A (Not applicable)- test object does meet the requirementP (Pass)- test object does not meet the requirementF (Fail)- test object does not demandND (Not demanded)Testing . :Date of receipt of test item . : Oct. 08, 2014Date(s) of performance of test

16、s . : Oct. 08, 2014 Oct. 12, 2014Test item particulars . :Equipment mobility . : movableX hand-heldX transportable stationary for building-in direct plug-inConnection to the mains pluggable equipment type A type B permanent connection detachable power supply cord non-detachable power supply cordX no

17、t directly connected to the mainsOperating conditionX continuous rated operating / resting time:Over voltage category . : OVC I OVC II OVC III OVC IVX other: Supplied by external power adapter. Mains supply tolerance (%)N/ATested for IT power systems . : YesX NoIT testing, phase-phase voltage (V)N/A

18、Class of equipment . : Class I Class IIX Class III Not classifiedMass of equipment (kg): EUT with battery: 0.125kg(including battery)Pollution degree . : PD 1X PD 2 PD 3IP protection classPX0Summary of testing:The equipment under test (EUT) has been evaluated at maximum ambient (Tma) of +45 C accord

19、ing to the manufacturers declaration.All tests were measured under the worst case and the maximum load conditions.Test Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 7 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: custo

20、TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan BranchGeneral remarks:Remark 1: the original test report is Test report No: LD141124N045 dated on Dec. 10, 2014. Remark 2: this report is copied test report based on test report LD141124N045,-

21、 changed manufacturer, factory.- updated label by the requirement of client, detail see page 5 Remark 3: for remark 2), no test needs to be performed.The test results presented in this report relate only to the object tested.This report shall not be reproduced, except in full, without the written ap

22、proval of the Issuing testing laboratory.(see Enclosure #) refers to additional information appended to the report. (see appended table) refers to a table appended to the report.Throughout this report acomma /point is used as the decimal separator.General product information:1) The equipment is a Mo

23、bile Phone which supplied by a certificated power adapter or internal battery;2) The maximum ambient temperature is specified as 45C;3) Dimension of the EUT: 143mm by 70mm by 8mm;4) The test sample was a pre-production sample without serial number.5) The maximum ambient temperature of adapter report

24、 is specified as 40C, so maximum ambient temperature of 45C was considered in this report. See attachment 1 (evaluation some test for external adapter with model TC28)6) The sound pressure complied with the requirements of EN 50332-1, and evaluated in test report No. MT141124N045 which issued by Bur

25、eau Veritas Shenzhen Co., Ltd. Dongguan Branch dated on 2014- 12-09.Test Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 8 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT I

26、EC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch1.5ComponentsP1.5.1GeneralComponents, which were found to affect safety aspects, are complied with the requirements of this standard or within the safety aspects of the relevant IEC component standards.PComply with IEC 60950-1 or re

27、levant component standard(See appended table 1.5.1)P1.5.2Evaluation and testing of componentsComponents which are certified to IEC and/or nation standards are used correctly within their ratings.Components not covered by IEC standards are tested under the conditions presentin the equipment.P1.5.3The

28、rmal controlsNo thermal controls.N/A1.5.4TransformersNo such component.N/A1.5.5Interconnecting cablesInterconnecting cable for Interconnection is carryingonly SELV voltages on an energy level below 240 VA.Except for the insulation material, there is no further requirements to the o/p interconnection

29、 cable.P1.5.6Capacitors bridging insulationNo such component.N/A1.5.7Resistors bridging insulationNo such component.N/AResistors bridging functional, basic or supplementary insulationNo such component.N/AResistors bridging double or reinforced insulation between a.c. mains and other ci

30、rcuitsNo such component.N/AResistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cableNo such component.N/A1.5.8Components in equipment for IT power systemsThe EUT is not directly connected to the mains.N/A1.5.9Surge suppressorsNo such component.N/A1GENE

31、RALPIEC 60950-1ClauseRequirement TestResult - RemarkVerdictTest Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 9 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 609

32、50-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch1.7Marking and instructionsP1.7.1Power rating and identification markingsSee below.PPower rating markingOptional.N/AMultiple mains supply connections.:N/ARated voltage(s) or voltage range(s) (V) . :5VdcN/ASymbol for nature of supply,

33、for d.c. only . :DCN/ARated frequency or rated frequency range (Hz) . :N/ARated current (mA or A) . :1AN/AIdentification markingsSee below.PManufacturers name or trade-mark or identification mark . :Trade-mark:PModel identification or type reference . :PGN-506PSymbol for Class II equipment on

34、ly . :Class III equipment.N/AOther markings and symbols . :Additional symbols or markings do not give risk to misunderstanding.P1.6Power interfaceP1.6.1AC power distribution systemsThe EUT is not directly connected to the AC mains.N/A1.6.2Input current(see appended table 1.6.2)P1.6.3Voltage limit of

35、 hand-held equipmentThe rated voltage of hand- held equipment not exceed 250 VP1.6.4Neutral conductorThe EUT is not directly connected to the AC mains.N/AGeneralNo such component.N/AProtection of VDRsNo such component.N/ABridging of functional insulation by a VDRNo such componen

36、t.N/ABridging of basic insulation by a VDRNo such component.N/ABridging of supplementary, double or reinforced insulation by a VDRNo such component.N/AIEC 60950-1ClauseRequirement TestResult - RemarkVerdictTest Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town,

37、Dongguan City, Guangdong 523942, ChinaPage 10 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch1.7.2Safety instructions and markingSafety related information in English has b

38、een evaluated. Manufacturer commits to provide them in the language of the countries where the product will be distributed.PGeneralSee below.N/ADisconnect devicesThe EUT is not directly connected to the mains supply.N/AOvercurrent protective deviceNo such device.N/AIT pow

39、er distribution systemsThe EUT is not directly connected to the mains supply.N/AOperator access with a toolNo tool is necessary when operate this product.N/AOzoneThis EUT is not intended to produce the ozone.N/A1.7.3Short duty cyclesThe EUT is designed for continuous operation.N/A1.7.4

40、Supply voltage adjustment . :No such device.N/AMethods and means of adjustment; reference to installation instructions . :No such device.N/A1.7.5Power outlets on the equipment . :No power outlet.N/A1.7.6Fuse identification (marking, special fusing characteristics, cross-reference) . :No such compone

41、nt.N/A1.7.7Wiring terminalsSee below.N/AProtective earthing and bonding terminals . :No such terminalsN/ATerminals for a.c. mains supply conductorsThe EUT is not directly connected to the AC mains.N/ATerminals for d.c. mains supply conductorsThe EUT is not directly connected to

42、the DC mains.N/A1.7.8Controls and indicatorsNo safety affecting controls and indicators.N/AIdentification, location and marking . :No such partsN/AColours . :N/ASymbols according to IEC 60417 . :N/AMarkings using figures . :N/AIEC 60950-1ClauseRequirement TestResult - Rem

43、arkVerdictTest Report No: LD141216N020No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 11 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dong

44、guan Branch2PROTECTION FROM HAZARDSP2.1Protection from electric shock and energy hazardsN/A2.1.1Protection in operator access areasClass III equipment, suppied by SELV and there is no hazardous voltage generated inside the EUT.N/AAccess to energized partsClass III equipment, suppied by SELV a

45、nd there is no hazardous voltage generated inside the EUT.N/ATest by inspection . :N/ATest with test finger (Figure 2A) . :N/ATest with test pin (Figure 2B) . :N/ATest with test probe (Figure 2C) . :N/ABattery compartmentsNo battery compartment provided in TNV circuit.N/AAccess to ELV

46、wiringNo ELV wiring inside the EUT.N/AWorking voltage (Vpeak or Vrms); minimum distance through insulation (mm)Access to hazardous voltage circuit wiringClass III equipment, no circuit wiring with hazardous voltage inside the EUT.N/A1.7.9Isolation of multiple power sources . :Not used.N/A1.7.

47、10Thermostats and other regulating devices . :No such parts.N/A1.7.11DurabilityAfter this test there was no damage to the label. The marking on the label did not fade. There was no curling or lifting on the label edge.P1.7.12Removable partsMarking was not show on removable part.N/A1.7.13Replaceable

48、batteries . :Caution was provided in the user manual.PLanguage(s) . :Only English language reviewed.1.7.14Equipment for restricted access locations. :Not intended for use in the restricted access locations.N/AIEC 60950-1ClauseRequirement TestResult - RemarkVerdictTest Report No: LD141216N020No. 34,

49、Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, ChinaPage 12 of 77Tel: +86 769 8593 5656Fax: +86 769 8599 1080Email: TEST REPORT IEC/EN 60950-1 VER.2Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch2.3TNV circuitsN/A2.3.1LimitsNo TNV circuit .N/AType of TNV circuits . :2.3.2Separation from other circuits and from accessible partsNo TNV circuit .N/A2.2SELV circuitsP2.2.1General requirementsSee below.P2.2.2Voltages under normal conditions (V) . :Class III equipment,