手机产品质量检验标准

手机产品质量标准本产品质量标准由以下四个部分组成：第一部分：产品技术规格书（电性能部分）第二部分：产品外观检验标准第三部分：产品功能检验标准第四部分：产品可靠性检验标准第一部分：产品技术规格书（电性能部分）1 GSM 900MHz 电性能测试标准GSM900射 频 载 波 功 率信道功率等级Peak burst power （dBm）Average power （dBm）标准range标准rangeULLLULLLCH1PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100CH62PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100CH124PCL5333531333531PCL8273024273024PCL161115711157PCL1951005100发射功率/时间特性信道功率等级测试内容标准CH1PCL5Power time template发射功率突发脉冲在GSM规范要求的功率/时间波罩内CH62CH124相 应 误 差信道功率等级Phase error peak（dg）Phase error RMS（dg）GBGBCH1PCL5205CH62205CH124205频率误差信道功率等级标准(Hz)CH1PCL590CH6290CH12490接收误码率信道等级标准resultCH1Ber class2150小时。白卡测试结果供参考。2通话时间测试Communication time test测试手机在通话时，电池在额定容量下维持手机通话的最长时间.The battery with rate capacity, Inspect the max time to communicate with the handset.电池在额定容量下，将手机听筒音量开到最大，分别在移动网和联通网，手机呼叫建立通话联系后，至到自动关机为止。记录各自手机的通话时间，5台平均即为手机通话时间；要求手机关闭其它设置，网络信号在-65-85dBm范围内.The battery with rate capacity, the volume set the max.Mobile Card and Unicom Card division of communication. Record each set the longest commun5PCS推荐大于120分钟（具体按产品定义）Commended more than 120 minutes (According to the product SPEC)3温升实验Temperature rise test验证手机在通话过程中，手机温度是否会升高并超过标准要求.Inspect the temperature variety of handset during communicating.最大功率发射。并工作于CH62。装入低电电池，开机、充电状态下将手机与模拟基站建立连接，持续通话90分钟。持续通话中，听筒音量开到最大，实时测量手机表面（按键、电池表面）、听筒部分的温度值；分别以90分钟内测量到的手机表面及听筒部分的最高温度值为最终实验温度。The handsets with the max transmit power in channel 62, Low electrical voltage, power on and charge. Communicate with the2PCS通话过程中不能出现掉话现象，试验后功能、性能正常。手机表面温度上升不超过15，听筒部分不能超过12.Interrupted exception is not allowed during the test. The function and performance is normal after test. The surface temperature variety is not more than 15. The receiver temperature variety is not mor环境试验 Environment Test4高低温贮存Hot/Cold test in storage验证手机在高低温环境条件下贮存的适应性Validate the capacity of the handset to be stored in low and high temperature conditions.被测样机不包装、不通电状态放进具有20的试验箱内。使试验箱在30分钟内温度达到-253，温度稳定后持续48小时,然后在30分钟内又使温度回到20;在30分钟内使试验箱内温度达到702，温度稳定后持续48小时，再在30分钟内使试验箱内温度回复到20，放置期满，被测样机进行试验后检查。Put the unpacked and power off samples in the test box in 20 temperature.The room temperature reduce to10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.5高低温工作Hot/Cold test in operation验证手机在高低温环境条件下使用的适应性Validate the capacity of the handset to be operation in low and high temperature conditions.被测样机不包装、处于通电待机状态，放进具有20的试验箱内。使温度在30分钟内达到-203，温度稳定后持续16时，然后在30分钟内又使温度回到20；再使试验箱在30分钟内温度达到+552，温度稳定后持续16小时，再在30分钟内使试验箱内温度回复到20，持续期满。立即进行被测样机试验后检查。Put the unpacked and switched on samples in the test box in 20 temperature.The room temperature reduc10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.6恒定湿热Damp Heat test验证手机在恒定湿热环境条件下使用的适应性.Inspect the performance of the handset under high temperature and high humidity.被测样机不包装、处于通电待机状态，以翻盖打开位置放进试验箱内。使温度达到+402，湿度达到95%（+2%/-3%），稳定后持续96小时，持续期满。立即进行被测样机试验后检查。put the unpacked, power on and folder opened samples into the constant temperature box. When the temperature arrive retentively +402 and humidity is 95（+2%/-3%）10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.7温度冲击实验Thermal shock test验证手机经受环境温度迅速变化的能力.Inspect the performance of the handset under the vertiginous temperature.被测样机不包装、不带电池状态，以正常位置放进试验箱内。高温为+702，稳定温度保持时间2h；低温为403，稳定温度保持时间2h；转换时间不大于5分钟；循环次数为12次（1个循环周期为4小时5分钟）。循环期满，在正常大气条件下放置2h。放置期满，被测样机进行试验后检查。put the unpacked and power off 5pcs QC pASSED samples into the Thermal Shock Box. High temperature is 702, keep t10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.8结露实验Dew test验证手机在结露环境下的适应性.Validate the performance of the handset under the dew environment.待机状态下，按照+202/95%（+2%/-3%）湿度放置2h；-203放置30min；转换时间40min设置进行试验，共连续进行5个循环；试验结束后立即进行测试。The samples idle, Do the test as the temperture is 202 and the humidity is 95%（+2%/-3%） for 2h; then the temperture is -203 for 30minutes, conversion time in 40minu5PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.9污物混入实验Filth interfuse test验证手机结构密闭性.Validate the frame obturation of the handset.将电池装在手机上，关机状态下放入装有300目滑石粉的袋子中，上下振荡200次，左右振荡200次，前后振荡200次，共计600次。完成后取出观察主屏、副屏进尘程度。put the power off and with battery samples in the bag with talcuum powder 300 mesh, surge up and down 200 times, surge around 200 times, surge front and back 200 times, 605PCS污物不得进入LCD内，手机功能正常。LCD havent any filth. The function is normal.10极限温度充电实验Limit temperature Charge Test验证手机在极限温度条件下的充电性能Validate the performance of the handset to charge under the limit temperature condition.分别在-53及+452温度下，在手机达到环境温度并且稳定后充电30分钟，电池电压能够上升。Under the temperture -53 and +452, Alternate charge the handset for 30minutes, the battery voltage must rise.5PCS手机充电指示正常（即充电指示灯点亮，充电图标跑动）；在手机达到环境温度并且稳定后充电30分钟，电池电压能够上升。The charge is show normal(the charge LED is light, charge ico is running); The battery voltage has risen after chargeing 30 minutes.11盐雾实验Salt mist test验证手机产品抗盐雾腐蚀的能力 Validate the resistance of the handset in the salt mist.溶液含量为5%的氯化钠溶液。将手机关机放在盐雾试验箱内(箱内温湿度分别为+352，90%（+2%/-3%）RH)，样机.竖直放置24h、正面放置10h、反面面放置10h，以免溶液喷洒不均或有的表面喷不到，样机需立即被放入测试箱。实验期满。取出样机，清水擦拭后烘干，进行试验后检查。put 5% NaCI liquor into the tester. put the power off samples in the salt mist test box(the room temperture is +3PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.12随机振动Random Vibration Test验证手机经受规定严酷等级的随机振动的能力Validate the performance of the handset under asperity vibration athletics.被测样机不包装、处于通电待机状态。牢固固定在试验台上。试验参数：+6dB/oct，频率范围10-20Hz ；频率范围20-500Hz，功率频谱密度0.05 g2/Hz。轴向：三个轴向。持续时间：每方向1小时，共3小时。持续时间结束，取出被测样机进行试验后检查。Fixup the unpacked and power on samples on the test table. Test parameter: +6dB/oct，frequency is from 5 to 20Hz and from 203PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.13正弦振动Sinusoidal vibration test模拟手机在运输过程中产生的振动。Simulate the transport vibration, and validate the handsets reliabilty.样机不包装、处于插卡通电待机状态，在振幅1.5mm，频率范围5-10Hz ；在加速度为3g，频率范围10-200Hz ；以1 oct/mn扫频速度进行X、Y、Z三个方向，每个方面各振动1小时，共3个小时，试验结束后进行试验后检测；The samples in unpacked and power on with SIM card. Frequency from 5 to 10Hz, swing is 1.5mm; Frequency from 10 to 200Hz, acceleration is5PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.14包装振动packaging vibration endurance Test检验手机包装材料对手机产品的保护作用及手机结构配合、机壳材料的耐磨性、部件焊接质量等Validate the protect ability from the wrapper, structure inosculate of the product, wearability of the shell material and solder quality of the components etc.被测样机包装好放于试验台上。试验参数：频率5-200Hz ，振幅15-20mm，在X、Y、X三个正弦方向各振动1小时，共3小时。持续时间结束，取出被测样机进行试验后检查。put the packed samples on the test table. Test parameter：Frequency from 5 to 200Hz, swing from15 to 20mm, every axis vibrate for 1h, sum up 3h. Duration over,take out an1箱1box样机及手机配件通过基本功能、性能及外观测试；The handset and fittings can pass base function,performance and appearance.15包装跌落packaging drop endurance Test检验手机包装材料对手机及附件的年外观、功能等的保护作用Validate the protect ability of the appearance and function from the wrapper.以包装出货的整箱手机按一角三边六面各跌一次，试验后结样机及配件进行全检。跌落标准如下：当产品毛重G10kg时，进行1M高度跌落；当产品毛重10kgG20kg时，进行80CM高度跌落；当产品毛重G20kg时，则进行60CM高度跌落；The handset packed with case waiting for shipment, drop 1 time of 1 angle, 3 edges, 6 faces. Final check of the samples and fittings1箱1box样机及手机配件通过基本功能、性能及外观测试；允许不多于2个（含2个）的内部包装破裂、损伤。The handset and fittings can pass base function,performance and appearance; Allow the inner packing and destroy crack 2 boxes at the most.161M跌落实验1M drop test验证手机及电池抗多次跌落于地上的能力Validate the capacity of the handsets and battery to resist being dropped repeatedly onto concrete.被测样机不包装、处于插卡通电待机状态。从1m高度（屏幕小于2.4,或不超过屏本身所在面积的40%)，初速度为0并自由跌落于光滑混凝土地面上，6个面、4条边，每面跌落2次,每条边跌1次，共计16次。每4次对样机外观、功能进行全检，试验结束，对样机进行全面检查。配套电池跌落：6个面、上方左右2条边各跌一次，共计8次，每2次对进行检查，试验结束，对电池进行全面检查。The samples unpacked and power on with SIM card, then drop from 1 mete10PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or a