SL500采煤机技术规格

1、SL500采煤机技术规格Eickhoff SL 500 AC Shearer Loader Specification艾柯夫SL 500交流采煤机技术规格Shearer Loader General采煤机整机Machine Model型号Eickhoff SL 500 ACTotal power installed总装机功率1915 kWVoltage电压3.3 kV, + 10%, -20%Capacity (peak cutting) 产量（最高产量）2700 t/h*Cutting Power截割功率2 x 750 kWHaulage Power牵引功率2 x 90 kWMaximum

2、haulage pull最大牵引力771 kNMaximum haulage speed最大牵引速度30.2 m/minHydraulic Drive Power泵电机功率35 kWLumpbreaker Power破碎功率200 kWCutting height采高app. 约5000 mmUndercut depth卧底量app. 约415 mmMachine height from floor机身高度app. 约 2041 mmClearance for coal passing过煤口高度app. 约780 mmDistance between drum center两滚筒中心距1330

3、0 mmDistance between haulage (sprockets) 牵引齿轨轮间距6190 mmCutting drum diameter滚筒直径2300 mmCutting drum width滚筒宽度900 mmCutting depth截深800 mmDrum speed滚筒转速23 r.p.m.Maximum cutability of mineral最大截割硬度up to可达100 Mpa*Haulage system牵引系统Eicotrack 2000 or similar销排系统或类似Rack wheel齿轨轮Eicotrack 2000 or similar销排系

4、统或类似Machine weight机器重量app. 约100 tNoise level噪音等级approx. 约80 dB (A)Face gradient in conveyor direction工作面纵向倾角max 10 without brakes最大10时不带制动器Face gradient transverse to conveyer工作面横向倾角max 10最大10 PF 6 / 1142型前刮板运输机No. 序 号Item项 目 名 称Technical Specification技 术 指 标1.General概述1.1Type and standard规格型号PF 6/1

5、1421.2Manufacturer生产厂家Bucyrus Europe GmbH比塞洛斯欧洲有限公司1.3Transport capacity(t/h) 运输能力(t/h)2500 t/h1.4Design length（m）设计长度（m）320 m (for calculation of max. required drive power 用于计算所需最大功率)1.5Laying length(m) 铺设长度(m)300 m (as defined by the enduser 用户要求)1.5aOrdered length (m) 订货长度300 m (quoted length 投标长

6、度)1.6Dimension of line pan (mm)中部槽外形尺寸 (mm)1756 mm1.7Structure characters of line pan 中部槽结构特点Welded structure with rolled profiles 轧制槽邦钢，焊接型式1.8Connecting method of line pan 中部槽联接方式Dogbone哑铃销1.9Applicable face inclination ()适应的工作面倾角()+/- 101.10Applicable entry inclination ()适应的工作面走向倾角()+/- 61.11Powe

7、r supply voltage /allowed change range (V) 供电电压/允许波动范围(V)3.3 kV1.12Power supply frequency (Hz)供电频率(Hz)50 Hz1.13Total installed power (kw)总装机功率(kW)2x1050kW1.14Chain speed(m/s) 链速(m/s)1.53 m/s1.15Spacing of flight bar (m)刮板间距(m)876 mm1.16Discharge method卸载方式Overhead discharge端卸1.17Discharge height（mm）

8、卸载高度（mm）Approx. 约1200 mm1.18Soft-start mode软启动方式CST1.19Layout of the drive devices 驱动装置的布置方式Parallel平行布置1.20Shearer haulage method 采煤机牵引轨道型式Jumbotrack 20001.21Normal start under the full load (Yes/No) 在满载条件下能否正常启动Yes是1.22Cooling method and parameters 冷却方式及参数Water cooled水冷1.23Noise（dB）噪音（dB）851.24Ove

9、rhaul period大修周期(Mt)Refer to warranty section参见质保期条款1.25Total weight(kg) 总重量(kg)t.b.a.1.26The whole machine warranty period (Mt)整机质保期(Mt)Refer to warranty section参见质保期条款1.27The whole machine service life(Mt)整机寿命(Mt)Refer to warranty section参见质保期条款2Chain tensioning device链条自动张紧装置2.1Type型式PM4 controll

10、ed 由PM4控制装置控制2.2Type of control devices控制装置形式Pressure, stroke measurement 监测压力、行程数据2.3Structure and principle结构原理Hydraulic cylinder in tg drive通过机尾驱动部液压油缸作用3Chain sprocket链轮3.1Structure type结构形式Cast, split sprocket 铸造、剖分式链轮3.2Tooth number齿数73.3Tooth surface hardness齿面硬度50 -55 HRC3.4Weight (kg) 重量(kg

11、)900 kg3.5Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款4Line pan（different line pans to be described respectively）溜槽（各种溜槽分别叙述）4.1Structure type结构形式PF 6/11424.2Outer dimension(LWH) 、inner width（ mm）外形尺寸(LWH) 、内宽（ mm）1836 x 1804 x 624 mm4.3Connecting mode连接方式Dogbone 哑铃销4.4The vertical applicable an

12、gle of the connecting part ()连接处垂直方向适应角度()Approx. 约+/- 3.64.5The horizontal applicable angle of the connecting part ()连接处水平方向适应角度()Approx.约 +/- 14.6Deck plate thickness (mm)中板厚度(mm)30+254.7Deck plate material中板材料S690Q + HDX 4004.8Bottom plate thickness (mm)底板厚度(mm)30 mm4.9Bottom plate material底板材料HD

13、X 4004.10Connecting device strength (kN)连接装置强度(kN)4500 kN4.11Type of bottom chain check device 底链检查装置形式Inspection holes in gobside profile each pan每节溜槽槽邦老塘侧设有观察孔One out of each 5 pans has inspection door.5每6槽中含一节观察槽All face end rerouting pans have inspection door所有端头及变线槽均为观察槽4.12weight(kg) 溜槽重量(kg)A

14、pprox. 约2620 kg4.13life(Mt) 溜槽寿命(Mt)Refer to warranty section参见质保期条款5Chains and flight链条和刮板5.1Chain type链条型号TIB 42x1465.2Chain manufacturer链条制造厂商Thiele5.3Chain link type链环型式Welded 焊接5.4Chain speed(m/s) 链速(m/s)1.53 m/s5.5Chain link specification (DT mm)链环规格(DT mm)42x146 mm5.6Minimum breaking force of

15、 chain (kN)链条最小破断力(kN)2220 kN5.7Chain material：链条材料：DIN 171155.8Unit chain weight(kg/m)单链重量(kg/m)36 kg/m5.9Chain elongation rate (%)链条延伸率(%)14 %5.10Chain centers (mm)两条链间中心距(mm)165 mm5.11Manufacturing standard制造标准DIN 171155.12Fatigue life疲劳寿命90000 cycles min最小寿命循环次数900005.13Life (Mt)寿命(Mt)Refer to w

16、arranty section参见质保期条款5.14Chain connector material连接环材料Block type组合块型式5.15Minimum breaking force of chain connector (kN)连接环最小破断力(kN)2220 kN5.16Elongation rate of chain connector (%)连接环延伸率(%)14 %5.17Fatigue life疲劳寿命90000 cycles min最小寿命循环次数900005.18Flight bar type刮板型号PF 6/1142-TIB42x1465.19Flight bar

17、manufacturer刮板制造厂商Bucyrus Europe GmbH比塞洛斯欧洲有限公司5.20Spacing of flight bar (mm) 刮板间距(mm)876 mm5.21Flight bar mounting method 刮板固定方式Bolted螺栓固定5.22Weight of flight bar (kg) 刮板重量(kg)55 kg5.23Material of flight bar刮板材质42 CrMo 45.24Flight bar service life (Mt)刮板使用寿命(Mt)Refer to warranty section参见质保期条款6Othe

18、rs附属部分6.1Spillplate height (mm)挡煤板高度(mm)Approx. 1370 mm; to be clarified at DLM约1370 mm待设计联络会确定6.2Fastening type固定形式Bolted螺栓固定6.3Cable groove height(mm)电缆槽高度(mm)to be clarified at DLM待设计联络会确定6.4Traction system of shearer and its technical parameters采煤机的牵引系统及技术参数Jumbotrack 2000, max.最大牵引力1000kN6.5Cen

19、tral height of sprocket of tail drive (mm) 机尾回转端链轮中心高度Approx. 大约900mm6.6Head frame, basement structure and parameter explanation 机头机架及底座结构、参数说明Please refer to drawing 见图 0902.157.000.00.00 and 0902.157.100.00.00-02Detailed information after final design 最终设计完成后确定技术细节6.7Tensile drive end bracket and

20、basement structure and parameter explanation 可张紧机尾驱动架及底座结构、参数说明Please refer to drawing 见图 0902.157.000.00.00 and 0902.157.300.00.00-02Detailed information after final design 最终设计完成后确定技术细节7Drive motor 电机7.1Type, number型号、数量27.2Manufacturer制造厂家Morley (摩利)7.3Single speed/double speed单速/双速single speed单速

21、7.4Rated power(kW) 额定功率(kW)1050 kW7.5Rated voltage/allowed variation range (V)额定电压/允许波动范围(V)3.3 kV7.6Rated current(A) 额定电流(A)215,77.7Rated power factor (cos)额定功率因数(cos)0,8757.8Rated rotational speed(r.p.m)额定转速(r.p.m)14927.9Start torque /rated torque起动扭矩/额定扭矩200%7.10Start current /rated current起动电流/额

22、定电流574%7.11The biggest torque 最大扭矩200% FLT7.12Frequency (Hz) 频率(Hz)507.13Rated frequency额定频率507.14Insulation class绝缘等级H7.15Connecting mode接线方式Star7.16Working mode工作方式SI DUTY7.17Flameproof type and standard防爆的类型和标准Zone1, Group1, Gas Group 17.18Protection class防护等级IP557.19Cooling mode冷却方式TEWJC IC3A1W7

23、7.20Allowed temperature rising range() 允许温升()1157.20aCooling water pressure冷却水压力t.b.a.7.20bCooling water flow冷却水流量t.b.a.7.21Over-heat protection过热保护Winding Thermostats+RTDs7.22Matched cable biggest outer diameter (mm)适配电缆的最大外径(mm)70mm dia. multicore cable 多芯电缆7.23Type and standard of cable connectin

24、g pin(jack) 电缆接线插头(插座)的型号、规格Victor, Plug +Socket7.24Manufacturing standard制造标准EN50014/18 Harmonised7.25Outer dimension(LWH mm)外形尺寸(LWH mm)1688x950x11327.26weight(kg) 重量(kg)52007.27Life (Mt) 寿命(Mt)8 MT8Soft-start devices 软启动装置8.1Type型式、型号CST8.2Manufacturer制造厂Bucyrus Europe GmbH比塞洛斯欧洲有限公司8.3Main work

25、principle主要工作原理Friction clutch摩擦片离合器8.4Main structure parameter主要结构参数Included in Gearbox包括在减速箱部分8.5Control mode控制方式PMC-D 8.6Performance curve性能曲线n.a.无8.7Weight(kg) 重量(kg)Approx. 约9700 kg8.8Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款9Drive devices 传动装置9.1Manufacturer 制造商Bucyrus Europe GmbH比塞洛斯欧洲

26、有限公司9.2Type型号KP-45 CST-V9.3Structure style结构形式Bevel-Planetary行星锥齿轮9.4Transmission ratio变速比339.5Lubricating mode and lubricant(grease) technical parameters 润滑方式及润滑油（脂）的技术参数Splash飞溅润滑9.6Cooling mode and parameter冷却方式及参数Water cooled水冷，25 l/min; max. 30 bar最大; max. 25C最高9.7Noise噪声= 85 dB9.8Outer dimensi

27、on(LWH mm)外形尺寸(LWH mm)2875x 1285 x 2106 mm9.9Weight(kg) 重量(kg)Approx. 约9700 kg9.10Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款B. Rear AFC PF 6 / 1342型后刮板运输机No. 序 号Item项 目 名 称Technical Specification技 术 指 标2.General概述1.1Type and standard规格型号PF 6/13421.2Manufacturer生产厂家Bucyrus Europe GmbH比塞洛斯欧洲有限公司

28、1.3Transport capacity(t/h) 运输能力(t/h)3000 t/h1.4Design length（m）设计长度（m）320 m (for calculation of max. required drive power 用于计算所需最大功率)1.5Laying length(m) 铺设长度(m)300 m (as defined by the enduser 用户要求)1.5aOrdered length (m) 订货长度300 m (quoted length 投标长度)1.6Dimension of line pan (mm)中部槽外形尺寸 (mm)1756 mm1

29、.7Structure characters of line pan 中部槽结构特点Welded structure with rolled profiles 轧制槽邦钢，焊接型式1.8Connecting method of line pan 中部槽联接方式Dogbone哑铃销1.9Applicable face inclination ()适应的工作面倾角()+/- 101.10Applicable entry inclination ()适应的工作面走向倾角()+/- 61.11Power supply voltage /allowed change range (V) 供电电压/允许波

30、动范围(V)3.3 kV1.12Power supply frequency (Hz)供电频率(Hz)50 Hz1.13Total installed power (kw)总装机功率(kW)2x1050kW1.14Chain speed(m/s) 链速(m/s)1.53 m/s1.15Spacing of flight bar (m)刮板间距(m)876 mm1.16Discharge method卸载方式Overhead discharge端卸1.17Discharge height（mm）卸载高度（mm）Approx. 约1115 mm1.18Soft-start mode软启动方式CST

31、1.19Layout of the drive devices 驱动装置的布置方式Parallel平行布置1.20Shearer haulage method 采煤机牵引轨道型式Jumbotrack 20001.21Normal start under the full load (Yes/No) 在满载条件下能否正常启动Yes是1.22Cooling method and parameters 冷却方式及参数Water cooled水冷1.22Cooling mode and parameter冷却方式及参数Water cooled水冷，25 l/min; max. 30 bar最大; ma

32、x. 25C最高1.23Noise（dB）噪音（dB）851.24Overhaul period大修周期(Mt)Refer to warranty section参见质保期条款1.25Total weight(kg) 总重量(kg)t.b.a.1.26The whole machine warranty period (Mt)整机质保期(Mt)Refer to warranty section参见质保期条款1.27The whole machine service life(Mt)整机寿命(Mt)Refer to warranty section参见质保期条款2Chain tensioning

33、 device链条自动张紧装置2.1Type型式PM4 controlled 由PM4控制装置控制2.2Type of control devices控制装置形式Pressure, stroke measurement 监测压力、行程数据2.3Structure and principle结构原理Hydraulic cylinder in tg drive通过机尾驱动部液压油缸作用3Chain sprocket链轮3.1Structure type结构形式Cast, split sprocket 铸造、剖分式链轮3.2Tooth number齿数73.3Tooth surface hardne

34、ss齿面硬度50 -55 HRC3.4Weight (kg) 重量(kg)900 kg3.5Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款4Line pan（different line pans to be described respectively）溜槽（各种溜槽分别叙述）4.1Structure type结构形式PF 6/13424.2Outer dimension(LWH) 、inner width（ mm）外形尺寸(LWH) 、内宽（ mm）1756 x 1746 x 395 mm4.3Connecting mode连接方式Dogb

35、one 哑铃销4.4The vertical applicable angle of the connecting part ()连接处垂直方向适应角度()Approx. 约+/- 64.5The horizontal applicable angle of the connecting part ()连接处水平方向适应角度()Approx.约 +/- 14.6Deck plate thickness (mm)中板厚度(mm)30+254.7Deck plate material中板材料S690Q + HDX 4004.8Bottom plate thickness (mm)底板厚度(mm)3

36、0 mm4.9Bottom plate material底板材料HDX 4004.10Connecting device strength (kN)连接装置强度(kN)4500 kN4.11Type of bottom chain check device 底链检查装置形式Inspection holes in gobside profile each pan每节溜槽槽邦老塘侧设有观察孔One out of each 5 pans has inspection door.5每6槽中含一节观察槽All face end rerouting pans have inspection door所有端

37、头及变线槽均为观察槽4.12weight(kg) 溜槽重量(kg)Approx. 约2450 kg4.13life(Mt) 溜槽寿命(Mt)Refer to warranty section参见质保期条款5Chains and flight链条和刮板5.1Chain type链条型号TIB 42x1465.2Chain manufacturer链条制造厂商Thiele5.3Chain link type链环型式Welded 焊接5.4Chain speed(m/s) 链速(m/s)1.53 m/s5.5Chain link specification (DT mm)链环规格(DT mm)42x

38、146 mm5.6Minimum breaking force of chain (kN)链条最小破断力(kN)2220 kN5.7Chain material：链条材料：DIN 171155.8Unit chain weight(kg/m)单链重量(kg/m)36 kg/m5.9Chain elongation rate (%)链条延伸率(%)14 %5.10Chain centers (mm)两条链间中心距(mm)165 mm5.11Manufacturing standard制造标准DIN 171155.12Fatigue life疲劳寿命90000 cycles min最小寿命循环次数

39、900005.13Life (Mt)寿命(Mt)Refer to warranty section参见质保期条款5.14Chain connector material连接环材料Block type组合块型式5.15Minimum breaking force of chain connector (kN)连接环最小破断力(kN)2220 kN5.16Elongation rate of chain connector (%)连接环延伸率(%)14 %5.17Fatigue life疲劳寿命90000 cycles min最小寿命循环次数900005.18Flight bar type刮板型号

40、PF 6/1342-TIB42x1465.19Flight bar manufacturer刮板制造厂商Bucyrus Europe GmbH比塞洛斯欧洲有限公司5.20Spacing of flight bar (mm) 刮板间距(mm)876 mm5.21Flight bar mounting method 刮板固定方式Bolted螺栓固定5.22Weight of flight bar (kg) 刮板重量(kg)77 kg5.23Material of flight bar刮板材质42 CrMo 45.24Flight bar service life (Mt)刮板使用寿命(Mt)Ref

41、er to warranty section参见质保期条款6Others附属部分6.1Breaking mechanism (Y/N)有无破碎机构No 无6.2Breaking mechanism style破碎机构形式n.a. 无6.3Central height of sprocket of tail drive (mm) 机尾回转端链轮中心高度Approx. 大约900mm6.4Head frame, basement structure and parameter explanation 机头机架及底座结构、参数说明Please refer to drawing 见图 0902.157

42、.000.00.00 and 0902.157.100.00.00-02Detailed information after final design 最终设计完成后确定技术细节6.5Tensile drive end bracket and basement structure and parameter explanation 可张紧机尾驱动架及底座结构、参数说明Please refer to drawing 见图0902.157.000.00.00 and 0902.157.300.00.00-02Detailed information after final design 最终设计完

43、成后确定技术细节7Drive motor 电机7.1Type, number型号、数量27.2Manufacturer制造厂家Morley （摩利）7.3Single speed/double speed单速/双速single speed单速7.4Rated power(kW) 额定功率(kW)1050 kW7.5Rated voltage/allowed variation range (V)额定电压/允许波动范围(V)3.3 kV7.6Rated current(A) 额定电流(A)215,77.7Rated power factor (cos)额定功率因数(cos)0,8757.8Rat

44、ed rotational speed(r.p.m)额定转速(r.p.m)14927.9Start torque /rated torque起动扭矩/额定扭矩200%7.10Start current /rated current起动电流/额定电流574%7.11The biggest torque 最大扭矩200% FLT7.12Frequency (Hz) 频率(Hz)507.13Rated frequency额定频率507.14Insulation class绝缘等级H7.15Connecting mode接线方式Star7.16Working mode工作方式SI DUTY7.17Fl

45、ameproof type and standard防爆的类型和标准Zone1, Group1, Gas Group 17.18Protection class防护等级IP557.19Cooling mode冷却方式TEWJC IC3A1W77.20Allowed temperature rising range() 允许温升()1157.21Over-heat protection过热保护Winding Thermostats+RTDs7.22Matched cable biggest outer diameter (mm)适配电缆的最大外径(mm)70mm dia. multicore c

46、able多芯电缆7.23Type and standard of cable connecting pin(jack) 电缆接线插头(插座)的型号、规格Victor, Plug +Socket7.24Manufacturing standard制造标准EN50014/18 Harmonised7.25Outer dimension(LWH mm)外形尺寸(LWH mm)1688x950x11327.26weight(kg) 重量(kg)52007.27Life (Mt) 寿命(Mt)8 MT8Soft-start devices 软启动装置8.1Type型式、型号CST8.2Manufactu

47、rer制造厂Bucyrus Europe GmbH比塞洛斯欧洲有限公司8.3Main work principle主要工作原理Friction clutch摩擦片离合器8.4Main structure parameter主要结构参数Included in Gearbox包括在减速箱部分8.5Control mode控制方式PMC-D 8.6Performance curve性能曲线No 无8.7Weight(kg) 重量(kg)Approx. 约9700 kg8.8Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款9Drive devices 传

48、动装置9.1Manufacturer 制造商Bucyrus Europe GmbH比塞洛斯欧洲有限公司9.2Type型号KP-45 CST-V9.3Structure style结构形式Bevel-Planetary行星锥齿轮9.4Transmission ratio变速比339.5Lubricating mode and lubricant(grease) technical parameters 润滑方式及润滑油（脂）的技术参数Splash飞溅润滑9.6Cooling mode and parameter冷却方式及参数Water cooled水冷，25 l/min; max. 30 bar

49、; max. 25C9.7Noise噪声= 85 dB9.8Outer dimension(LWH mm)外形尺寸(LWH mm)2875x 1285 x 2106 mm9.9Weight(kg) 重量(kg)Approx. 约9700 kg9.10Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款C. BSL PF6/1542转载破碎机1. General概述NO. 序 号Item项 目 名 称Technical Specification技 术 指 标1.1Type and standard规格型号PF 6/15421.2Manufacture

50、r生产厂家Bucyrus Europe GmbH比塞洛斯欧洲有限公司1.3Transport capacity(t/h) 转载能力(t/h)3500 t/h1.4Control mode控制方式1.5Laying length(m) 铺设长度(m)49.5m1.6Structure characters of the middle groove 中部槽结构特点Welded design焊接型式1.7Connecting ways of the middle groove 中部槽联接方式Dogbone, bolts哑铃销，螺栓连接1.8Chain speed(m/s)链速(m/s)1,74 m/

51、s1.9Distance between Flights(m)刮板间距(m)504 mm1.10Applicable working face obliquity ()适应的工作面倾角()+/- 101.11Applicable working face tending obliquity ()适应的工作面走向倾角()+/- 61.12Power supply voltage/allowed change range (V) 供电电压/允许波动范围(V)3.3 kV1.13Power supply frequency (Hz)供电频率(Hz)50 Hz1.14The whole machine power (kw)总装机功率(kW)600 kW1.15Drive mode (structure) 驱动方式（结构）Tensionable drive frame; ove