斯巴鲁力狮

斯巴鲁力狮Tag内容描述：<p>1、检修斯巴鲁力狮发动机故障警告灯亮检修斯巴鲁力狮发动机故障警告灯亮 一辆行驶里程约 64000km 装配了手自一体电控 4 速变速器的斯巴鲁力狮 2 5 轿车 车主反映 该车 在 2 挡升 3 档 3 挡升 4 挡时换挡冲击严重 在 3。</p><p>2、维修手册指南 1 维修手册指南维修手册指南 使用本维修手册使用本维修手册 通过遵守屏幕中的说明，人们可利用维修手册和 SSM （SUBARU Select Monitor ）之间的手册 链接从 DTC 检查结果中显示需要的维修手册诊断图 表。 也可将其视为一种常规维修手册光盘， 将其装至 未安装 SSM 的 PC 中。在实际的故障诊断工作期 间， 如果要与维修手册结合使用， 或在。</p><p>3、SL-60 Key Lock Cylinders SECURITY AND LOCKS 19.Key Lock Cylinders A: REPLACEMENT 1. FRONT DOOR 1) Raise the front door glass to the top position. 2) Remove the door trim. 3) Remove the sealing cover.。</p><p>4、ME(H4SO)-48 Timing Belt MECHANICAL 15.Timing Belt A: REMOVAL NOTE: When replacing a single part, perform the work with the engine assembly installed to body. When performing the work with the engi。</p><p>5、FS-35 Front Arm FRONT SUSPENSION 6. Front Arm A: REMOVAL 1) Lift up the vehicle, and then remove the front wheels. 2) Remove the front arm. (1) Remove the nut and disconnect the front stabilizer link。</p><p>6、DS-23 Front Hub Unit Bearing DRIVE SHAFT SYSTEM 4. Front Hub Unit Bearing A: REMOVAL 1) Lift up the vehicle, and then remove the front wheels. 2) Remove the axle nut. CAUTION: Do not loosen the axle n。</p><p>7、FU(H4SO)-33 Manifold Absolute Pressure Sensor FUEL INJECTION (FUEL SYSTEMS) 10.Manifold Absolute Pressure Sensor A: REMOVAL 1) Disconnect the ground cable from battery. 2) Remove the cover (A) and cli。</p><p>8、FU(H4SO)-73 Fuel Delivery and Evaporation Lines FUEL INJECTION (FUEL SYSTEMS) 28.Fuel Delivery and Evaporation Lines A: REMOVAL WARNING: Place “NO OPEN FLAMES” signs near the working area. CAUTION: Be。</p><p>9、FS-20 Cradle FRONT SUSPENSION 3. Cradle A: REMOVAL 1) Set the vehicle on a lift. 2) Adjust the tilt position of the steering column to the lowest position and lock the tilt lever. 3) Prevent the steer。</p><p>10、EN(H4SO)(diag)-78 List of Diagnostic Trouble Code (DTC) ENGINE (DIAGNOSTICS) 18.List of Diagnostic Trouble Code (DTC) A: LIST DTCItemNote P0026Intake Valve Control Solenoid Circuit Range/Performance。</p><p>11、EI-39 Front Bumper EXTERIOR/INTERIOR TRIM 9. Front Bumper A: REMOVAL 1) Disconnect the ground cable from battery. 2) Remove the front bumper face assembly. (1) Remove the clips, turn over the front mu。</p><p>12、CS-2 General Description CONTROL SYSTEMS 1. General Description A: COMPONENT 1. AT SELECT LEVER CS-01244 T2 (12) (10) (11) (13) (14) (15) (16) (17) (18)(19) (20) (21) (22) (23) T2 (24) (25) (27) T1 (9。</p><p>13、CO(H6DO)-17 Radiator COOLING 6. Radiator A: REMOVAL CAUTION: The radiator is pressurized when the engine and radiator are hot. Wait until engine and radi- ator cool down before working on the radiator。</p><p>14、AB-18 Airbag Connector AIRBAG SYSTEM 2. Airbag Connector A: PROCEDURE 1. POWER SUPPLY 1) How to disconnect: CAUTION: When pulling the slide lock or disconnecting connector, be sure to hold the connect。</p><p>15、LU(H4SO)-37 Oil Level Switch LUBRICATION 12.Oil Level Switch A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift up the vehicle. 3) Remove the under cover. 4) Drain the engine oil. 5) Disc。</p><p>16、SE-57 Power Seat System SEATS 4. Power Seat System A: REMOVAL CAUTION: When removing the front seat, Disconnect the ground cable from battery before disconnecting the side airbag module harness connec。</p><p>17、CVT(diag)-35 Diagnostic Procedure with Diagnostic Trouble Code (DTC) CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) 16.Diagnostic Procedure with Diagnostic Trouble Code (DTC) A: DTC P0705 TRANSMISSI。</p><p>18、ME(H4SO)-2 General Description MECHANICAL 1. General Description A: SPECIFICATION Engine Model2.5 L Cylinder arrangement Horizontally opposed, liquid cooled, 4-cylinder, 4-stroke gasoline engine Valve。</p><p>19、FU(H4SO)-15 Throttle Body FUEL INJECTION (FUEL SYSTEMS) 2. Throttle Body A: REMOVAL 1) Disconnect the ground cable from battery. 2) Remove the cover (A) and clip (B) from air intake boot assembly. 3)。</p>