某某公司产品确认规格书

XX 公司2012-1-09 GIE0118B Page 1 of 14产 品 规 格 书SPECIFICATION FOR APPROVAL产品型号 GIE0118B 版本 A产品结构 5” G+G 产品类型 电容式触摸屏制作人（Prepared by）设计部审核（ Checked by）品管部审核（Checked by）总经办批准 （Approved by）请客户仔细阅读规格书中的各项内容，当对规格书内各项内容表示认可时；请在下面客户确认项中签字（此规格书为一式两份） 。Please read the following carefully the contents of the customer, the customer said after the signing of the cover on the confirmation of the customer to acknowledge the contents. 客户确认确认人 (Confirmed by)设计部审核 (Checked by)品管部审核 (Checked by)批准 (Approved by)变更记录表序号 版本号 修改人 修改内容概要 批准 生效日期1 A 陈小艳 初次发行2345XX 公司2012-1-09 GIE0118B Page 2 of 14目 录1 工程图 Engineering Drawing 2 产 品 结 构 Construction3 机 械 特 性 Mechanical Characteristics4 电 气 特 性 Electrical Characteristics5 光 学 特 性 Optical Characteristics6 使 用 环 境 Processing Environment7 引脚定义 PIN Assignment8 驱动 IC Controller IC9 机械测试 Mechanical TestXX 公司2012-1-09 GIE0118B Page 3 of 1410 寿命测试 Life Test11 环境测试 Environment Test12 检 验 标 准 Inspection Standard13 包 装 及 运 输 Package2.测试半径 Bending Radius: R1.0 mm;3.测试次数 Bending Times: 50 Times;4.测试重量 Load: 500g.XX 公司2012-1-09 GIE0118B Page 9 of 144 FPC 插拔测试 FPC Insert/Pull Out Test: (1) 作业环境：温度：223、湿度：6010RH、 Level：等级 1000Operating Environment:Temperature:223、Humidity:6010RH、Level:Class1000(2) 测试方法：Test Method:A.测试前确认电性特性符合规格；Before Test: Electrical Characteristic Test is OK.B.测试步骤：开卡锁连接器插入 FPC锁住 FPC开卡锁连接器插入 FPC锁住 FPC，重复 10 次；Test Circle: Connector Unlock FPC Insert Connector Lock Connector Unlock FPC Pull Out Connector Lock, cycle 10 Times;C.测试后再次确认电性特性符合规格.After Test: Electrical Characteristic Test is OK;10 寿命测试 Life Test(1)作业环境：温度：223、湿度：6010RH、 Level：等级 1000Operating Environment:Temperature:223、Humidity:6010RH、Level:Class100011 环境测试 Environment Test(1)高温测试 High temperature：+80，120 hr.(2)低温测试 Low temperature：-20 ，120 hr.(3)高温高湿测试 High temp./high humidity test：60 not twisted and bent FPC output, so as to avoid adverse FPC connection to the controller. (3)不可弯折 和分解本品。 Can not bend and break the product.(4)不要在产 品的动作区域滴上水滴，以免引起误操作。Do not drop the product of the action on the drop zone, in order to avoid misuse. 上机Installed (1)请勿在触 摸屏上施加过大压力而造成产品损伤。Does not touch too much pressure is applied to the product cause injury.(2)整机设计 时，请避免损伤FPC及 呈锐角状弯折FPC。Machine design; avoid injury and acute angle-shaped bend FPC FPC. (3)请勿在FPC与屏连接部 施加过大压力，导致屏体内部电气连接不稳定。 Do not connect the FPC and the department of screen put too much pressure, leading to screen the internal electrical connection is unstable. (4)组装时避 免工具损伤产品。Assembly of the product to avoid tool damage. (5)装机中尽量避免静电产生。Try to avoid static electricity installed.XX 公司2012-1-09 GIE0118B Page 14 of 14Beitai Company supplies quality guarantee of 1 year since the day of product purchase, and we would either repair or replace the bad products if they are unqualified from the beginning.3 以下情况不在我司保证范围之内，我司不给予返修或更换。具体如下：Our company would not repair or replace the products of the following conditions, which is out of guarantee scope; 3.1 产品交付客户后，因跌落或撞击或不当操作造成的不良品；Products damaged by falling, impacting or improper operation after delivering to customers;3.2 因为自然灾害造成的不良品；Products damaged by natural disaster;3.3 在未经我司同意之前，客户私自进行再加工处理的产品；Products processed by customers without any permission of our company;3.4 客户未按注意事项作业而造成的不良品。Products damaged by customers whoever conducts the operation without complying with the instructions.4 本确认书经客户承认后，客户不得有所变更，如需变更，需双方友好协商好重新出确认书认可，否则一切损失由贵公司负责。The customer should not change the Confirmation Document after approved by the customer. If