EDGE优化手册.doc_第1页
EDGE优化手册.doc_第2页
EDGE优化手册.doc_第3页
EDGE优化手册.doc_第4页
EDGE优化手册.doc_第5页
已阅读5页,还剩61页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

gprs service implement team, changsha office, motorola inc. 第 1 页 共 66 页 edgeedge 优化手册优化手册 (ver 1.0) 摩托罗拉电子(中国)有限公司长沙分公司摩托罗拉电子(中国)有限公司长沙分公司 gprs 优化服务组优化服务组 2008 年 1 月 22 日 gprs service implement team, changsha office, motorola inc. 第 2 页 共 66 页 文档说明:本文档针对摩托罗拉 gprs 无线 gsr8 版本。 文档修订历史 版本 更新日 期 撰稿人核稿人更新说明 1.0 1/22/2008 闫绍东、鄢 维、汪勇 鲁君之、 刘春晓、 夏江、谢 斌 初稿,根据 edge 优化实际经验及相关 edge 资料整理,为了指导 2008 湖南 edge 优化 gprs service implement team, changsha office, motorola inc. 第 3 页 共 66 页 目录目录 一:一:edge 开通的条件和准备开通的条件和准备.5 1.1:系统要具备的条件:系统要具备的条件5 1.2:硬件方面的准备:硬件方面的准备 .5 1.3:数据库准备:数据库准备 7 1.4:hlr 中中 sim 卡卡 edge 数据数据11 二:二:edge 的开通的开通.12 三三:edge 的无线和接口的优化的无线和接口的优化.15 3.1:edge 时隙优化时隙优化.15 3.1.1 edge和gprs时隙分载频设置.15 3.1.2 根据统计分析对时隙配置进行优化.16 3.2:接口优化:接口优化16 3.2.1 gsl接口.17 3.2.2gds接口20 3.2.3gb接口21 3.2.4a-bis接口.22 3.2.5gn/gi接口.23 3.3:prp 板优化板优化 .23 3.4:edge 无线优化无线优化.26 四:四:edge 的参数修改优化的参数修改优化.28 4.1:全局间协商参数:全局间协商参数 .28 4.2:bsc/pcu 级关键参数级关键参数 .29 4.3:小区级参数说明:小区级参数说明 .31 五:五:edge 的关键统计项优化指导的关键统计项优化指导.36 5.1:rlc 层的吞吐量层的吞吐量36 5.2:上:上/下行的各类编码速率的占用率下行的各类编码速率的占用率.41 5.3:bler.43 5.4:上行信道请求成功率:上行信道请求成功率45 5.5:tbf 建立成功率建立成功率.47 5.6:tbf 失败率失败率49 5.7:小区的拥塞:小区的拥塞 50 六:六:edge 的特性优化的特性优化.52 6.1 its feature.52 6.2 versatrau.53 gprs service implement team, changsha office, motorola inc. 第 4 页 共 66 页 七:七:edge 优化与优化与 gprs 优化的平衡优化的平衡 55 7.1 采用采用_cell_data参数控制参数控制 gprs 用户占用用户占用 edge 时隙的比例时隙的比例.55 7.2 4 粒度粒度 usf.55 7.3 参数参数gprs_sched_beta.56 八:八:edge 优化注意事项优化注意事项.57 8.1edge 开通失败处理开通失败处理 .57 8.2 edge 优化注意事项优化注意事项.64 gprs service implement team, changsha office, motorola inc. 第 5 页 共 66 页 一:一:edgeedge 开通的条件和准备开通的条件和准备 1.1:系系统统要具要具备备的条件的条件 msc 软件版本应支持 r99 以上版本 sgsn 软件版本应支持 r99 以上版本 hlr 对 gprs 用户作了定义,需要能够接收 edge class mark 即支持 r99 以上版本 bss 系统软件版本支持 edge 功能 使用 disp_options all 命令,如果可以看到第 59 号功能列在未受限功能列表 中,则表示 edge 功能未受限,具备开通 edge 的条件。 1.2:硬件方面的准硬件方面的准备备 1.2.1 edge 的基站要求 horizonii 已经支持。 horizonmacro 基站中需更换原有 tcu 载频板为 ctuii 载频板。 -niu(niu 与 t43 结合使用为 2m 线传输和主机柜与外部单元相连接提 供接口)必需配置起码一块 20mb 的 pcmcia 卡。 -如果机柜中 ctuii 满配置,则需要 3 个 psu(电源模块)。 mcell 基站需使用 ctuii(m)载频。 微蜂窝(老款的 micro 不支持,h2 mini indoor 和 h2 micro 支持,建议 采用 h2 mini indoor) 。 gprs service implement team, changsha office, motorola inc. 第 6 页 共 66 页 支持支持 edge 的的 ctu2 载频的特性载频的特性 在hi/hii机柜中支持 edge的ctu2 在mcell机柜中支持 edge的ctu2m 1.2.2 ctu-ii 载频的特性 支持一个单高功率载波(single density)用于支持 edge 或者支持 2 个双低功率载波(double density) 两种不可以同时支持 single density 下,ctu2 的 rf 输出功率比 ctu 高。但是使用 edge 和 8psk 时,edge 时隙的输出功率會波动+2db 和-15db (fluctuate within +2db| -15db boundaries ),这会导致小区覆盖收缩。 double density 下,2 个载频需要在同一小区里,但是可以分别复位。这 种模式下,不支持 edge(8psk) 只有 single density 才支持 edge 的配置和使用 在 gsr9 下,motorola 推出了 ctu2-d 的功能,功能支持 horizen ii 下 double 模式的载频,如果 a 面的载频上打开了 edge 功能,那么在 b 面载频上 不会丢失相对应 gmsk 时隙。 1.2.3pcu 的资源准备状况 gprs service implement team, changsha office, motorola inc. 第 7 页 共 66 页 prp for edge 建议满配置 2 个 pmc 4 条 gds(cs34 满配置需求为 2 个 pmc 2 条 gds),新定的 pcu 的 prp 板缺省都是 2 个 pmc 卡。 prp 资源:一块 prp 板支持 120 个 pdtch (不管 edge/cs34 与否) gds 资源:edge 时采用 64k trau 1.3:数据数据库库准准备备 1.3.1 换站的数据库准备换站的数据库准备 1)mcell 的基站换成 horizonii 基站需要收集如下相关基站信息,和现场工程 师进行交流 prp dproc pmc 1 trau gds pmc 2 unused trau gds unused current prp dproc configuration prp dproc pmc 1 trau gds pmc 2 trau gds trau gds trau gds egprs prp dproc configuration present for cs3/4 gprs service implement team, changsha office, motorola inc. 第 8 页 共 66 页 2)准备删站数据库,相应命令如下 关闭相关小区 gprs 功能: chg_cell_ele gprs_enabled 0 cell_number= cell_id 删除小区的邻区: del_nei cell_id all del_nei all cell_id 修改 gprs 的相关参数: chg_ele switch_gprs_pdchs 0 cell_number=cell_id chg_ele res_gprs_pdchs 0 cell_number=cell_id chg_ele sw_ts_less_one_carrier 0 cell_number=cell_id chg_ele res_ts_less_one_carrier 0 cell_number=cell_id 删除基站的硬件: lock dri dri_id lock 0 rsl rsl_id lock 0 path path_id uneq rtf rtf_id uneq dri dri_id del_cell cell_id uneq 0 rsl rsl_id uneq 0 path path_id gprs service implement team, changsha office, motorola inc. 第 9 页 共 66 页 删除基站: uneq 0 site 3)用工具收集原基站的参数备用 4)新站数据库准备,根据新站具体配置生成相关数据库文件 主要注意站型 的变化和载频的配置 a. 配置机柜类型 equip cab 1,机柜 id 2,机柜类型:24 horizonii 主机柜;25 horizonii 扩展机柜 3,频率类型: b.dri 的配置 dri single 模式模式 equip dri 1,enter the 1st and 2nd dri id: dri id(0 0,0 1,) 2,enter the density of this dri:1 3,enter the cabinet identifier:机柜标识 4,enter the type of connection to the btp:fox 标识:0 主机柜;1 扩展 1 机柜;2 扩展 2 机柜 gprs service implement team, changsha office, motorola inc. 第 10 页 共 66 页 5,enter the port to which the tcu is connected:机柜中槽位标识 6,enter the 1st and 2nd rtf id:对可以确定位置的 edge 载频可给出 rtf id 7,enter the gsm cell id where the dri appears:4 6 0 0 0 8,enter antenna select number for this cell:天线定义 9,does this dri use tuneable combining:no 10,enter diversity flag for this dri:1 11,enter the fm cell type:4 dri double 模式模式 equip dri 1,enter the 1st and 2nd dri id: dri id(0 0,0 1,) 2,enter the density of this dri:2 3,enter the cabinet identifier:机柜标识 4,enter the type of connection to the btp:fox 标识:0 主机柜;1 扩展 1 机柜;2 扩展 2 机柜 5,enter the port to which the tcu is connected:机柜中槽位标识 6,enter the 1st and 2nd rtf id:对可以确定位置的 edge 载频可给出 rtf id 7,enter the gsm cell id where the dri appears:4 6 0 0 0 8,enter antenna select number for this cell:天线定义 9,enter diversity flag for this dri:1 10,enter the fm cell type:4 修改数据库,完成新站的添加修改数据库,完成新站的添加 2. 关闭旧基站,配合现场工程人员,在 bsc 上执行准备好的删站文件 3. 添加新的基站,在 bsc 上执行准备好的新站文件 4. 用工具程序恢复此基站的优化参数 更换更换 ctu-ii 载频的步骤载频的步骤 2. 锁住需更换的载频lock dri dri_id 3. 删除需更换的载频数据uneq dri dri_id 4. 添加 ctu-ii 载频数据用于 edge 5. 解锁 ctu-ii 载频unlock dri dri_id 添加新的添加新的 ctu-ii 载频的步骤载频的步骤 2. 添加 ctu-ii 载频数据用于 edge 3. 解锁 ctu-ii 载频 unlock dri dri_id gprs service implement team, changsha office, motorola inc. 第 11 页 共 66 页 1.4: :hlr 中中 sim 卡卡 edge 数据数据 对湖南 hlr 厂商西门子和华为的 sim 要求举例,相关配置在 cds 测试 log 和核心网用 户信息中也可以检查。 1.4.1 西门子 hlr 中 edge sim 卡要求 hlr 中看下面的特性:(crqosprof ) the maxtransport ability 2048k the reliability class 3 delay low mthrput bestefrt 1.4.2 华为 hlr 中 edge sim 卡要求 prov=true, cntxid=2, relcls=ackrlcprodt, 等于西门子中的 3 peakthr=256000oct, 等于 2048k meanthr=best_effort, errsdu=no, trafficcls=interact, maxsdusize=1500 oct, maxbrupl=2048k, 最大上行比特率 maxbrdwl=2048k, 最大下行比特率 resber=0.00001, sduerr=0.0001, maxgbrupl=2048k, 可以保证的最大上行比特率(可选参赛或 256k) maxgbrdwl=2048k, 可以保证的最大下行比特率(可选参数或 256k) apn=“cmwap“; gprs service implement team, changsha office, motorola inc. 第 12 页 共 66 页 二:二:edgeedge 的开通的开通 1. 打开小区 gprs 功能 实例: chg_cell_element gprs_enabled 1 cell_number = cell_id enter the gprs rac: rac_id enter the ra_colour: ra_colour_id enter the number of reserved pdchs:保留的 pdch 的信道数 enter the number of switchable tchs/pdchs:可转换的 pdch 的信道数 enter the number of reserved pdchs if one carrier becomes unavailable: enter the number of switchable pdchs if one carrier becomes unavailable: enter the algorithm for gprs timeslot configuration:0 为自动分配,1 为 手工分配 enter the maximum number of gprs timeslots per carrier: 2. 查看基站 dri 和 rtf 的对应关系(开通 edge 功能的 rtf 必须落在 ctu-ii 载 频上) state dri * * 如果 bcch 落在 single 的 ctu-ii 载频上,应锁住此 dri 让 bcch 飘到其他载频上。再解锁此 single 的 ctu-ii dri 3. 打开 edge 功能 modify_value pkt_radio_type 64k rtf 4. 察看小区 edge 状态 a.a. disp_cell_sdisp_cell_s 实例: gprs service implement team, changsha office, motorola inc. 第 13 页 共 66 页 disp_cell_s 29 start of report for location 29: gsm cell id mcc 460 mnc 00 lac 4136 (1028h) ci 2887 (0b47h) rac 140 (008ch) - - primary freq type egsm secondary freq type n/a bcch frequency 32 - status unbarred gprs status unbarred egprsegprs statusstatus egprsegprs availavail pdch status pd available res pdch requested 5 sw pdch requested 25 reset in prog no gprs reset in prog no spi in prog no bss bssap prhb na msc bssap prhb na spi/msc sccp prhb na accclass bar none gprs accclass bar 4 egprsegprs chanchan reqreq availavail full power mode off ext range mode off active pcu site 0 free inuse unavl - - - sdcch 79 1 0 norm outer tch/f 26 5 0 norm inner tch/f 0 0 0 ext outer tch/f 0 0 0 norm outer tch/h 0 0 0 norm inner tch/h 0 0 0 norm outer tch/g 0 na 0 norm inner tch/g 0 na 0 pd channel 5 1 0 egprsegprs pdpd channelchannel 1111 1313 0 0 b.b. disp_cell_map gprs service implement team, changsha office, motorola inc. 第 14 页 共 66 页 disp_cell_map pcu_0 disp_cell_map 是用来查询 pcu 和小区的映射关系,使用方法为: disp_cell_map cellid:显示小区映射在哪个 pcu 上 disp_cell_map pcu_id:显示 pcu 上有那些小区 由于目前湖南的 bsc 只带一个 pcu,因此使用 disp_cell_map pcu_0 来查看 pcu 上管理的小区情况,主要的信息包括 cell_id 和小区的 gprs 状态: 实例: 通过 disp_cell_map 的命令,可以很清楚的看到小区的状态和 edge 开通的情况, egprs avail 表示 edge 开通,egprs unavail 表示 edge 未开通。 可以通过打 batch 的方式,获得所有 bsc 小区 edge 的开通情况,再针对 edge unavail 的小区进行故障处理或者开通。 gprs service implement team, changsha office, motorola inc. 第 15 页 共 66 页 三三:edgeedge 的无线和接口的优化的无线和接口的优化 3.1:edge 时隙优化 3.1.1 edge 和和 gprs 时隙分载频设置时隙分载频设置 cmcccmcc集团建议集团建议 edge only voice/ edge voice/ edge voice/ edge voicevoicevoicevoice 配置:edge 和 gprs 共载频, 1 个静态(edge only)+3 个动态时隙 优点:节省时隙资源,在一个载频完成。 缺点:不能发挥 edge 的最大功效,如 edge only 时隙数量少时,除了 edge only 的时隙其他时隙只能工作 gmsk 调制下,这样用户无法达到最大速率。但 edge only 时隙数量多时,又造成浪费 moto 建议 edge voice/ edge voice/ edge voice/ edge voicevoicevoicevoice gprs voice/ gprs voice/ gprs voice/ gprs voicevoicevoicevoice 一 个 小 区 载频a 载频b 配置:edge 和 gprs 分载频设置,例如 2 个分别是 1(静态)3(动态)设置。 优点:充分发挥 edgegprs 各自的性能 缺点:跨载频的时隙无法实现共享。 gprs service implement team, changsha office, motorola inc. 第 16 页 共 66 页 3.1.2 根据统计分析对时隙配置进行优化根据统计分析对时隙配置进行优化 对于找出 gprs 网络中存在 gprs 或 egprs 时隙配置不足的小区,主要是通 过分析小区拥塞、上/下行 pdtch 的利用率和上/下行 pdtch 的占用这 3 类指标。 对于在这 3 类指标中都超过门限值的小区,就应该要优先对该小区进行 gprs 时 隙的扩容了。在制定扩容计划时,一般建议对要扩容的小区先增加 1 个 gprs 时 隙,最多增加 2 个时隙,然后在扩容完成后再对资源利用率的指标进行统计和 分析,观察其小区是否还需要进行扩容,如果还需要再进行 1 到 2 个时隙的扩 容调整,直到合理满足该小区的 gprs 时隙需要,要注意的是在扩容后要注意 语音业务的话务量变化,尽量避免造成话务拥塞,如果造成话务拥塞就需要进 行载频的扩容。 3.2:接口优化 由于每时隙数据速率最大增加到 58kbps,每个载频所需的 backbaul 增加, 需要采用 64k 的 trau。 gds trau backhaul 也许要增加。每个使用 edge 的 pdch 在 pcu 和 bss 接口 上需要 64k 的时隙。 gbl 容量可能需要增加,这是因为高速话务的增加和空中接口的数据速率的 增加导致的 gprs service implement team, changsha office, motorola inc. 第 17 页 共 66 页 3.2.1 gsl 接口接口 1. the requirement for the number of gsls during system initialization (gslinit_time) is 6 6. 2. each gsl message consists of three parts: lapd protocol, bss executive header protocol, and the application message carrying actual signalling information. the lapd and bss protocol parts can be considered messaging overhead. also, in a similar manner to rsl, the gsl traffic depends on the access mechanism used on the air interface. the calculation for the required number of gsl links during run-time (after(after thethe systemsystem stabilizes)stabilizes) is as shown below. 3. with one phase access, there is additional loading on the rsl and gsl due to enhanced one phase messaging and immediate assignment messages for ul tbf setups. gslgsl信道估算信道估算 根据统计估算根据统计估算 gsl = max(gslrun_time , gslinit_time) gslinit = 6 gslrun_time = max (gsl_rach, gsl_ia + gsl_paging) gsl_rach = gprsrachespersecond * 5.5 / (1000*0.25) gsl_ia = 8.5 * gprsiaspersecond / (1000*0.25) gsl_paging = 8.5 * gprspagespersecond * no_lcfs_for_rsl / (1000*0.25) gprs service implement team, changsha office, motorola inc. 第 18 页 共 66 页 gprs service implement team, changsha office, motorola inc. 第 19 页 共 66 页 实例: 20072007年年1 1月月2929号号10:0010:00统计计算:统计计算: gprs rach(gprs_acc_per_rach)最大为118801。 (2007/01/29 10:00) immediate assignments(access_per_agch)为131679。 (2007/01/29 10:00) gprs paging(paging_reqs_ps)为57846。 每秒钟gprs rach为118801/3600=33.0,gsl-rach = 7.2 每秒钟gprs ia为36.6, gsl-ia =(8.5*36.6)/(1000*0.25)=1.24 每秒钟寻呼为57846/3600=16.06,lcf=9,gsl-paging= (8.5*16.06*9) /(1000*0.25)=4.9 gslgsl = = maxmax (6,(6, max(7.2,max(7.2, 6.14)6.14) = = 7.27.2 20072007年年1 1月月2929号号22:0022:00统计计算:统计计算: gprs rach(gprs_acc_per_rach)最大为58537。 (2007/01/29,22:00) immediate assignments(access_per_agch)为64346。 (2007/01/29,22:00) gprs paging(paging_reqs_ps)为27025。(2007/01/29,22:00) 每秒钟gprs rach为16.26(=58537/3600),gsl-rach = 1 每秒钟gprs ia为17.87(=64346/3600), gsl-ia = 1 每秒钟寻呼为7.5(=27025/3600),lcf=9,gsl-paging= 2.2 gslgsl = = maxmax (6,(6, max(1,max(1, 3.2)3.2) = = 6 6 gslgsl lapdlapd (gsl)(gsl) e1e1 gprs service implement team, changsha office, motorola inc. 第 20 页 共 66 页 the gsl traffic is load balanced over all gsls. the first e1 carries up to 30 lapd links and the second e1 up to another 30. for lapd-type gds resiliency, two e1s are recommended, regardless of the number of lapd channels required. for example, if only one channel is required to carry the expected signalling load, two e1s with one lapd channel per e1 should be used. the mproc load balancing software distributes the load evenly between the two lapd channels. gprocgproc lcflcf the gproc lcfs available at the bsc terminate up to 12 lapd channels. up to 60 lapd-type links may be provisioned at the pcu, for a total of 180 (for three pcus). the lapd links may be distributed on the lcf automatically, based on the capacity available on the lcfs. 建議每條picp上的lapd gds增加配置gsl到6條 總共2x6=12條gsl互為備份 負載均衡 增加的gsl對應到以前已經配置的一對lcf/gproc上 即gsl專用的一對 gproc管理全部12條gsl 3.2.2gds 接口接口 3.2.2.1 相关资源优化相关资源优化 gds 配置原则: gprs 与 edge 总时隙不能超过(120x prp 数) #16kbps ts + 2x #32kbps ts + 4x #64kbps 60,需要考虑增加需要考虑增加 gbl 资源资源,即扩即扩 gbl 时隙时隙. 3.2.4a-bis 接口接口 3.2.4.1 abis 资源需求变化: 由于 edge 无线时隙的最大数据传输速率为 59.2 kbit/s。 在 abis 接口,通常的 16 kbit/s 的 abis 信道速率无法满足更高 mcs 的数 据速率,因此需要引入更高速率的 abis 信道。 3.2.4.2 abis 资源配置方式 以载频为单位配置 abis 资源,资源在每载频的时隙内共享。 gsr7,要求每个 epdch 信道,配置一个 64k 的 abis 资源。 gsr8,支持 “压缩”功能,有两种 abis 资源压缩方案可供选择: 每 4 个 epdch 信道,配置 3 个 64k 的 abis 资源,平均速率相当于 mcs-6,约 41kbps/epdch。 每 4 个 epdch 信道,配置 2 个 64k 的 abis 资源,平均速率相当于 mcs-5,约 28kbps/epdhc。 abis 资源不足时,会降低承载业务的 mcs 级别。 无 abis 资源延迟释放机制。 一个 edge pdtch 占用 1 个陆地 ts 64k/s rtf 一个 gprs cs34 pdtch 占用 1/2 个陆地 ts 32k/s 一个 gsm tch/gprs pdtch 占用 1/4 个陆地 ts 16k/s 以此来计算 e1 是否够用 the configuration is assumed: rtf 0 0 has all 64kbps terrestrial channels allocated. rtf 1 0 has all 16kbps terrestrial channels allocated. rtf 2 0 has all 32kbps terrestrial channels allocated. display the ts usage of mms 0 0 at site 39 for rtf 0 0, rtf 1 0, and rtf 2 0. note in the output how rtf 1 0, which has all 16kbps terrestrial channels allocated, continues to use only 2 e1 timeslots, but rtf 0 0 requires 8 e1 gprs service implement team, changsha office, motorola inc. 第 23 页 共 66 页 timeslots. in addition, the sub-rates of the terrestrial timeslot are not displayed if the entire terrestrial timeslot is mapped to one air timeslot. 实例 mmi-ram 0115 - disp_mms_ts 0 0 0 start of report: site: 39 mms: 0 0 general timeslot usage: ts group usage device id type site ts 0 unavailable 1 64k_rsl 39 0 0 64k 39 2 unused 3 unused 4 unused . . . 18 rtf 2 0 0 full 1 19 rtf 2 0 0 full 1 20 rtf 2 0 0 full 1 21 rtf 2 0 0 full 1 22 rtf 1 0 0 full 1 23 rtf 1 0 0 full 1 24 rtf 0 0 0 full 1 25 rtf 0 0 0 full 1 26 rtf 0 0 0 full 1 27 rtf 0 0 0 full 1 28 rtf 0 0 0 full 1 29 rtf 0 0 0 full 1 30 rtf 0 0 0 full 1 31 rtf 0 0 0 full 1 end of report. 3.2.5gn/gi 接口接口 edge 的开通会增加 gn 和 gi 接口的流量,需核心网关注,如果最大流量 超过带宽的 50,建议扩容,现湖南 gn 和 gi 接口都是 1000m,暂时不会发 生拥塞情况。 gprs service implement team, changsha office, motorola inc. 第 24 页 共 66 页 3.3:prp 板优化 prp 资源:一块 prp 板支持 120 个 pdtch (不管 edge/cs34 与否) gds 资源:edge 时采用 64k trau gprs service implement team, changsha office, motorola inc. 第 25 页 共 66 页 gprs service implement team, changsha office, motorola inc. 第 26 页 共 66 页 3.4:edge 无线优化 3.4.1 不同接收电平影响说明 不同接收信号电平对edge下行吞吐量的影响 0 10 20 30 40 50 60 299(bcch)6348(non-bcch) 299(bcch)50.3741.8117.3 6348(non-bcch)50.0132.316.33 -50 -60-70 -80 修改当前参数 chg_element msc_release 取值影响: 影响edge应用; sgsn_release 参数描述: 指定bss与核心网络sgsn遵从的规范版本 取值范围: 0到1(r98,r99以后),默认值:0 推荐值参考: 对于edge 要求为 1 命令格式: 显示当前参数 disp_element sgsn_release 修改当前参数 chg_element sgsn_release 取值影响: 影响edge应用; gprs service implement team, changsha office, motorola inc. 第 29 页 共 66 页 4.2: :bsc/pcu 级级关关键键参数参数 delay_dl_rel_durdelay_dl_rel_dur 参数描述: 指定终端下行的 tbf 释放时间。 取值范围: 15 到 600(x20 毫秒),默认值:50 推荐值参考: 100 命令格式: 显示当前参数 disp_element delay_dl_rel_dur 修改当前参数 chg_element delay_dl_rel_dur 取值影响: tbf 释放时间过长对系统 rau 是有利,但对于小数据业务来说结束时间长; tbf 释放时间过段对系统 rau 是不利,终端会重新建立 tbf,但对于小数据业 务来说结束时间快,减少拖尾现象; delay_ul_rel_durdelay_ul_rel_dur 参数描述: 指定终端上行的 tbf 释放时间。 取值范围: 15 到 600(x20 毫秒),默认值:50 推荐值参考: 15 命令格式: 显示当前参数 disp_element delay_ul_rel_dur 修改当前参数 chg_element delay_ul_rel_dur 取值影响: tbf 释放时间过长对系统 rau 是有利,但对于小数据业务来说结束时间长; tbf 释放时间过长对系统 rau 是不利,终端会重新建立 tbf,但对于小数据业 务来说结束时间快,减少拖尾现象; gprs_ul_dl_biasgprs_ul_dl_bias 参数描述: 指定 class 6 和 10 类终端上行下行的优先级。 gprs service implement team, changsha office, motorola inc. 第 30 页 共 66 页 0 - ul bias 1 - dl bias 取值范围: 0,1 缺省值 1 推荐值参考: 0 命令格式: 显示当前参数 disp_element gprs_ul_dl_bias 修改当前参数 chg_element gprs_ul_dl_bias 取值影响: 影响终端对上下行优选,可视综合业务的上下行吞吐量来更改; gprs_sched_betagprs_sched_beta 参数描述: 设置 bss 对 tbf 资源调度算法,分三级: 0 每终端吞吐速率相同 1 每终端传输的数据块数量相同. 2 高编码占用终端优先。 取值范围: 0,1,2 默认值:1 推荐值参考: 2 命令格式: 显示当前参数 disp_element gprs_sched_beta 修改当前参数 chg_element gprs_sched_beta 取值影响: 对高编码的终端提供更好的 pdtch 信道的调度,好的吞吐能力;说明当 edge 终端在无线环境好的情况下将得到优先的 bss 的调度算法; eop_enabledeop_enabled 参数描述: 指定 gprs/edge 终端系统接入方式。 取值范围: 0 或 1 默认值:0 推荐值参考: 1 命令格式: gprs service implement team, changsha office, motorola inc. 第 31 页 共 66 页 显示当前参数 disp_element eop_enabled 修改当前参数 chg_element eop_enabled 取值影响: 加快终端的接入速度。 bssgp_fc_period_cbssgp_fc_period_c 参数描述: 指定 bss 像 sgsn 发送留空信息的时间间隔。 取值范围: 10 到 100(x100 毫秒),默认值:10 推荐值参考: 10 命令格式: 显示当前参数 disp_element bssgp_fc_period_c 修改当前参数 chg_element bssgp_fc_period_c 取值影响: 规范中规定,sgsn 负责流控算法的执行,而 bss 则负责提供 sgsn 执行各种 控制时的参数。这些参数通过 flow-control-pdu 在

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论