已阅读5页,还剩10页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1 管道组成件 Piping component管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管 steel pipe铸铁管 cast iron pipe碳钢管 carbon steel pipe合金钢管 alloy steel pipe不锈钢 stainless steel pipe塑料管 plastic pipe玻璃管 glass tube橡胶管 rubber tube直管 run pipe; straight pipe1.2 管件 Fitting弯头 elbow异径弯头 reducing elbow三通 tee异径三通 reducing tee等径三通 straight tee四通 cross等径四通 straight cross异径四通 reducing cross异径管 reducer活接头 union管帽 cap (C)堵头 plug短节 nipple1.3 弯管 Bend圆度 roundness1.4 法兰 Flange (FLG)整体管法兰 integral pipe flange钢管法兰 steel pipe flange法兰盖 blind flange, blind压力级 pressure rating, pressure rating class压力温度等级 pressure-temperature rating法兰密封面,法兰面 flange facing法兰面加工 facing finish粗糙度 roughness光滑的 smooth1.5 垫片 Gasket (GSKT)垫片的型式 type of gasket平垫片 flat gasket环形平垫片 flat ring gasket平金属垫片 flat metal gasket1.6 阀门 Valve1.6.1 阀门结构、零件阀杆 stem阀座 valve seat (body seat)阀座环、密封圈 seat ring阀芯(包括密封圈、杆等内件) trim阀体 body阀盖 bonnet本体阀杆密封 body stem seal石棉安全密封 asbestos emenen seal阀杆填料 stem packing1.6.2 常用阀(1)闸阀 gate valve(2) 截止阀 globe valve(3) 节流闪阀 throttle valve针阀 needle valve(4) 角阀 angle valve(5) Y型阀(Y 型阀体截止阀) Y-valve (Y-body globe valve)(6) 球阀 ball valve(7) 蝶阀 butterfly valve(8) 柱塞阀 piston type valve(9) 旋塞阀 plug valve三通旋塞阀 three-way plug valve四通旋塞阀 four-way plug valve(10) 隔膜阀 diaphragm valve(12) 止回阀 check valve1.6.3 其它用途的阀安全泄气阀 safety valve (SV)安全泄液阀 relief valve (RV)安全泄压阀 safety relief valve杠杆重锤式 lever and weight type电磁阀 solenoid valve, solenoid operated valve蒸汽疏水阀 steam trap气动阀 pneumatic operated valve机械式疏水阎 mechanical trap浮球式疏水阀 float trap放气阀(自动放气阀) air vent valve (automatic air vent valve) (疏水阀用)热膨胀阀 thermo expansion valve减压阀 pressure reducing valve, reducing valve1.6.4 未指明结构(或阀型)的阀切断阀 block valve; shut-off valve; stop valve调节阀 regulating valve集液排放阀 drip valve排液阀 drain valve放空阀 vent valve卸载阀 unloading valve排出阀 discharge valve吸入阀 suction valve取样阀 sampling valve总管阀 header valve1.7 管道特殊件 Piping Specialty1.7.1 管道特殊件(组件)粗滤器 strainer过滤器 filter丝网粗滤器 gauze strainer视镜 sight glass阻火器 flame arrester喷嘴;喷头 spray nozzle膨胀节 expansion joint消声器 silencer1.7.2 管道特殊元件Piping Special Element软管接头 hose connection (HC)快速接头 quick coupling橡胶管 rubber hose爆破片 rupture disk8字盲板 spectacle blind; figure 8 blind1.8 端部连接 End Connection法兰端 flanged end平端 plain end (PE)对焊连接(接头) butt welded joint法兰连接(接头) flanged joint2 管道用紧固件及螺纹2.1 紧固件螺栓 bolt螺母 nut粗制的 coarse精制的 finished, fine螺母 nut粗制的 coarse精制的 finished, fine3 材料、型钢及填料3.1 金属材料碳素钢 carbon steel (CS)低碳钢 low-carbon steel中碳钢 medium-carbon steel高碳钢 high-carbon steel普通碳素钢 general carbon steel优质碳素钢 high-quality carbon steel普通低合金结构钢 general structure low-alloy steel合金结构钢 structural alloy steel合金钢 alloy steel低合金钢 low alloy steel 中合金钢 medium alloy steel高合金钢 high alloy steel耐热钢 heat resisting steel高强度钢 high strength steel不锈钢 stainless steel (S.S.)铸件 casting熟铁,锻铁 wrought iron生铁 pig iron球墨铸铁 nodular cast iron; nodular graphite iron锻钢 forged steel铸钢 cast steel铸铁 cast iron (C.I.)3.1.4 材料性能极限强度 ultimate strength抗拉强度 tensile strength屈服极限 yield limit屈服点 yield point延伸率 percentage elongation抗压强度 compressive strength抗弯强度 bending strength弹性极限 elastic limit冲击值 impact value疲劳极限 fatigue limit蠕变极限 creep limit持久极限 endurance limit布氏硬度 Brinell hardness洛氏硬度 Rockwell hardness维氏硬度 Vickers diamond hardness, diamond penetrator hardness蠕变断裂强度 creep rupture strength断面收缩率 reduction of area韧性 toughess脆性 brittleness延性 ductility冷脆 cold shortness冷流 cold flow3.2 非金属材料 Non-metallic Material塑料 plastic塑料 plastic聚乙烯 polyethylene (PE)聚氯乙烯 polyvinyl chloride (PVC)聚丙烯 polypropylene (PP)聚苯乙烯 polystyrene (PS)聚碳酸酯 polycarbonate (PC)聚酰胺 polyamide (PA)聚甲基丙烯酸甲酯 polymethyl methacrylate (PMMA)聚烯烃 polyolefin (PO)热塑性塑料 thermoplastic热固性塑料 thermosetting plastics树脂 resin环氧树脂 epoxy, epoxy resin合成橡胶 synthetic rubber橡胶 rubber天然橡胶 natural rubber玻璃 glass木材 wood陶瓷 ceramic搪瓷 porcelain enamel耐火砖 fire brick3.4 填料及填料函填料 packing石棉绳 asbestos rope, asbestos cord自密封 self-sealing填料函压盖 stuffing box gland金属填料 metallic stuffing填料箱,填料函 packing box, stuffing box浸聚四氟乙烯的石棉填料 Teflon impregnated asbestos packing4.1 管道材料规定 Piping Material Specification管道等级 piping class; piping classification管道等级号 class designation公称直径 nominal diameter (DN); nominal (pipe) size公称压力 nominal pressure (PN)压力级,等级,类别 class (CL)低压 low pressure (L.P.)中压 medium pressure (M.P.)高压 high pressure (H.P.)大气压 atmosphere (ATM)真空 vacuum工作压力 operating pressure; working pressure设计压力 design pressure工作温度 operating temperature设计温度 design temperature环境温度 ambient temperature腐蚀裕量 corrosion allowance管道附件 piping attachment管道元件 piping element壁厚 wall thickness (WT)壁厚系列号 schedule number (SCH. No.)加厚的,加强的 extra heavy, extra strong双倍加厚的,双倍加强的 double extra heavy, double extra strong通用连接组 typieal installation分组(类)形式(如管道等级表) block form数据库 data base文件 file4.2 材料统计 Material Take-off (MTO)汇总表 summary sheet材料表 bill of material (BM)综合管道材料表 consolidated piping material summary sheet (CPMSS)统计材料准确度 accuracy of take-off材料情况报告 material status report (MSR)散装材料 bulk material编位号的 itemized代码 code number短代码 short code数量 quantity (QTY)重力 weight净重 net weight毛重 gross weight4.2 材料统计 Material Take-off (MTO)汇总表 summary sheet材料表 bill of material (BM)综合管道材料表 consolidated piping material summary sheet (CPMSS)统计材料准确度 accuracy of take-off材料情况报告 material status report (MSR)散装材料 bulk material编位号的 itemized代码 code number短代码 short code数量 quantity (QTY)重力 weight净重 net weight毛重 gross weight5 设备布置及管道布置Plot Plan and Piping Layout,Equipment and Piping Arrangement5.1 设备名称 Equipment Name5.1.1 容器 Vessel(1) 塔 tower, column洗涤塔 scrubber吸收塔 absorber冷却塔 cooling tower精馏塔 fractionating tow(2) 反应器 reactor汽提塔 stripper脱气塔 degasifier合成塔 synthesis tower蒸馏塔 distillation tower再生塔 regenering tower(3) 气柜 gas-holder螺旋式气柜 helical gas-holder湿式气柜 wet gas-holder干式气柜 dry gas-holder(4) 槽罐贮罐 tank; storage tank缓冲罐 knock out drum球罐 spheroid, spherical tank闪蒸罐 flash drum溶液贮槽 solution storage tank(5) 其它设备分离器 separator旋风分离器 cyclone搅拌器 agitator干燥器 dryer混合器 mixer萃取器 extractor结晶器 crystallizer吸附器 adsorber喷头 sprayer消声器 silencer火炬 flare(6) 换热器、加热器、冷却器换热器 heat exchanger空冷器 air cooler水冷却器 water cooler冷凝器 condenser螺旋板式换热器 spiral plate heat exchanger蒸发器 evaporator再沸器 reboiler急冷器 quencher预热器 preheater加热器 heater再热器 reheater(6) 换热器、加热器、冷却器换热器 heat exchanger空冷器 air cooler水冷却器 water cooler冷凝器 condenser螺旋板式换热器 spiral plate heat exchanger蒸发器 evaporator再沸器 reboiler急冷器 quencher预热器 preheater加热器 heater再热器 reheater空分装置 air separation facility软管站,公用工程站 hose station (HS), utility station设施 facilities罐区 tank yard成套设备 package unit5.4 厂房、站、单元5.5 设备布置设备位号 equipment item number工厂 plant工厂区界 plant limit项目区界内侧 inside battery limit (I.S.B.L.)项目区界 batterylimit (BL)区界 area limit区域边界 zone iimit界外 off site东 east (E)西 west (W)南 south (S)北 north (N)上 up下 down工厂北向 plant north真实北向 true north道路 road小过道 cat walk, cat way走道,过道 walk way, gangway, access way污水坑(井) sump pit集水池 catch basin沟槽 through预留区 trough场地 future area铺砌区 paving area非铺砌区 unpaved area碎石铺面 gravel paving橡皮铺面 rubber paving面积,区域 area体积,容积 volume (VOL)详图 detail5.6 管道布置管道设计 piping design管道研究 piping study走向研究 routing study重要管道 critical piping地上管道 above ground piping地下管道 under ground piping管网 network of pipes管廊 pipe rack管沟 piping trench管间距 line spacing管道跨距 line span总管 header, manifold旁路 by pass排液 drain放空 vent上升管,垂直管 riser导管 canduit裸管 bare iine管件直接 fitting to fitting (FTF)管段,接口 spool piece, spool取样接口 sampling connection集液包 drip leg伴热管 tracing pipe蒸汽伴热 steam tracing热水伴热 hot-water tracing电伴热 electrical tracing夹套管 jacketed line, jacketed piping全夹套的 full jacketed平面 plan详图 detail5.6 管道布置管道设计 piping design管道研究 piping study走向研究 routing study重要管道 critical piping地上管道 above ground piping地下管道 under ground piping管网 network of pipes管廊 pipe rack管沟 piping trench管间距 line spacing管道跨距 line span总管 header, manifold旁路 by pass排液 drain放空 vent上升管,垂直管 riser导管 canduit裸管 bare iine管件直接 fitting to fitting (FTF)管段,接口 spool piece, spool取样接口 sampling connection集液包 drip leg伴热管 tracing pipe蒸汽伴热 steam tracing热水伴热 hot-water tracing电伴热 electrical tracing夹套管 jacketed line, jacketed piping全夹套的 full jacketed平面 plan比例 scale图例 legend符号 symbol方位 orientation相交 intersection水平的 horizontal垂直的,立式的 vertical垂直,正交,垂直的 perpendicular平行,平行的 parallel计算机辅助设计 computer aided design (CAD)水平安装 horizontal installation垂直安装 vertical installafion对称的 symmetric相反(的),对面(的) opposite入口 inlet, suction出口 outlet, discharge排出口 exhaust距离 distance5.8 相关专业的专业词汇5.8.1 工艺(1) 图及表流程图 flow diagram工艺流程图 process flow diagram (PFD)管道及仪表流程图 piping andinstrument flow diagram (PID)公用工程流程图 utility flow diagram (UFD)管线表 line list; line schedule命名表;管道表 nomenclature设备表 equipment list (schedule)(2) 流体 fluid空气 air仪表空气 instrument air工艺空气 process air低压蒸汽 low pressure steam中压蒸汽 medium pressure steam高压蒸汽 high pressure steam伴热蒸汽 tracing steam饱和蒸汽 saturated steam过热蒸汽 superheated steam氧气 oxygen氢气 hydrogen氮气 nitrogen燃料气 fuel gas天然气 natural gas火炬气 flare gas酸性气 sour gas液化石油气 liquefired petroleum gas (LPG)氨气 ammonia gas冷却水 cooling循环水 circulating water锅炉给水 boiler feed water热水 hot water蒸汽冷凝水 steam condensate盐水 brine工艺水 process water化学污水 chemical sewage润滑油 lubricating oil溶剂 solvent溶液 solution聚合物 polymer硫酸 sulphuric acid盐酸 chlorhydric acid硝酸 nitric acid烧碱 caustic soda工艺液体 process liquid工艺气体 process gas(3) 流体特性 fluid characteristics蒸汽压 vapor pressure临界温度 critical temperature临界点 critical point临界压力 critical pressure比热 specific heat湿度 humidity密度 density比重 specific gravity粘度 viscosity闪点 flash point融点 melting point凝固点 freezing point浓度 concentration爆炸极限 limit of explosion有毒的 toxic可燃的;易燃的 flammable(4) 其它回收 recovery再生 regeneration循环 cireulatlon再循环;再生 recycle补充 make-up制备 preparation蒸汽吹扫 steaming out吹扫 purge抽空;排空 evacuation吹出 blow-off排污 blow down备用 stand-by化学清洗 chemical cleaning环境温度 ambient temperature成品 product污染 contamination大气污染 atmospheric pollution进料 feed5.8.3 仪表常开 normally open常闭 normally closed压力计 manometer; pressure gauge温度计 thermometer液位计 level gauge流量计 flow meter孔板 orifice联锁 interlock变送器 transmitter仪器;设备 apparatus仪器分析 instrumental analysis气相色谱仪 gas chromatograph液相色谱仪 liquid chromatograph质谱分析 mass spectrometric analysis化学分析 chemical analysis气体分析 gas analysis5.8.3 仪表常开 normally open常闭 normally closed压力计 manometer; pressure gauge温度计 thermometer液位计 level gauge流量计 flow meter孔板 orifice联锁 interlock变送器 transmitter仪器;设备 apparatus仪器分析 instrumental analysis气相色谱仪 gas chromatograph液相色谱仪 liquid chromatograph质谱分析 mass spectrometric analysis化学分析 chemical analysis气体分析 gas analysis5.8.5 设备管口 nozzle人孔 manhole (MH)轴 shaft附件,附属设备 accessory5.8.6 水道软水 soft water硬水 hard water饮用水 potable water循环冷却水给水 cooling water supply循环冷却水回水 cooling water return消防水 fire water苦咸水(碱性水) brackish water生活污水 sanitary sewer工业废水 industrial waste water脱盐水 demineralized water8 隔热、隔声管壳 shell隔热;融热层 insulation保温 hot insulation保冷 cold insulation导热系数 thermal conductivity fac
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 校企合作上课协议书
- 代理分公司合同范本
- 危险运动免责协议书
- 村民草原防火协议书
- 代理办理证件协议书
- 万象城商铺合同范本
- 树莓种植承诺协议书
- 医生事业编合同范本
- 坪山新区土地整备中心公开招聘普通雇员招聘易考易错模拟试题(共500题)试卷后附参考答案
- 代工施工安全协议书
- 2023-2024学年重庆市大渡口区化学九上期中监测模拟试题含解析
- 医院医疗临床带教培训课件:临床护理带教新思路
- 六年级上册美术课件-7.纸雕花卉 -冀教版
- GB/T 26081-2022排水工程用球墨铸铁管、管件和附件
- YS/T 514.7-2009高钛渣、金红石化学分析方法第7部分:氧化钙、氧化镁量的测定火焰原子吸收光谱法
- GB/T 30732-2014煤的工业分析方法仪器法
- 教师资格证考试心理学复习题
- 髋关节Harris评分表
- 学术规范与论文写作课件
- 2021年秋五年级数学上册四多边形的面积第5课时梯形的面积刘徽的出入相补原理拓展资料北师大版
- 富士5000G11和G7S参数设定
评论
0/150
提交评论