某省电信汇聚交换机OLT双上行配置模板.doc

汇聚交换机olt双上行配置模板v2华为s8505模式一：单链路+smar-link1. 板卡硬件要求：要求板卡中带有“db”字样并且软件版本在1267以上、或者没有“db”字样软件版本在1628以上，可以支持灵活qinq 。2. 软件版本要求：release1600以上可以配smart-link3. 配置命令 定义vlan acl acl number 4001 rule 0 permit ingress 51 to 1050 egress any /匹配普通宽带拨号用户vlan rule 1 permit ingress 43 egress any /匹配itv用户vlan rule 2 permit ingress 45 egress any /匹配itms终端管理vlan 定义外层vlanvlan 501-502 901-902 1701-1702 smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 1 undo flush enablesmart-link group 2 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 2 undo flush enableinterface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按顺序排列，只要不重复即可。interface gigabitethernetx/x/x /下行接口2 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 502 902 1702 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 4 nested-vlan 502 traffic-redirect inbound link-group 4001 rule 1 system-index 5 nested-vlan 1702 traffic-redirect inbound link-group 4001 rule 2 system-index 6 nested-vlan 902interface gigabitethernetx/x/x-01 /端口做为instance 1主用，instance 2备用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 port smart-link group 1 masterport smart-link group 2 slaveinterface gigabitethernetx/x/x-02 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 port smart-link group 1 slave port smart-link group 2 master 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令display smart-link group 1模式二：链路捆绑+smart-link1. 板卡硬件要求：要求板卡中带有“db”字样并且软件版本在1267以上、或者没有“db”字样软件版本在1628以上，可以支持灵活qinq 。2. 软件版本要求：release1600以上可以配smart-link3. 配置命令 定义vlan acl acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定义外层vlanvlan 501 1701 901 定义链路组link-aggregation group 1 mode manuallink-aggregation group 2 mode manual smart-link配置stp region-configuration instance 1 vlan 501 901 1701active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 1link-aggregation group 1 master /链路组1作为master link-aggregation group 2 slave /链路组2作为slaveundo flush enableinterface gigabitethernetx/x/x /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按顺序排列，只要不重复即可。interface gigabitethernetx/x/x-01 /主用上行口-1port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-02 /主用上行口-2port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-03 /备用上行口-1port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2interface gigabitethernetx/x/x-04 /备用上行口-2port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令display smart-link group 1display link-aggregation verbose模式三：单链路/链路捆绑+vlan双向透传1. 板卡硬件要求：要求板卡中带有“db”字样并且软件版本在1267以上、或者没有“db”字样软件版本在1628以上，可以支持灵活qinq。2. 软件版本要求：无特殊要求3. 配置命令 定义vlan acl acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定义外层vlanvlan 501 1701 901 vlan双向透传配置interface gigabitethernetx/x/x /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按顺序排列，只要不重复即可。interface gigabitethernetx/x/x-01 /上行口1port link-type trunk port trunk permit vlan 48 50 501 901 1701interface gigabitethernetx/x/x-02 /上行口2port link-type trunk port trunk permit vlan 49 501 901 1701 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令display vlan x/x/x华为s9300模式一：单链路+smar-link 灵活qinq配置：（s9300主机版本为v100r001版本或业务单板类型最后一个字母为a的单板使用如下流策略配置灵活qinq）1、 定义内层vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户vlantraffic classifier qinqa-2if-match vlan-id 43 /匹配itv用户vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itms终端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外层vlantraffic behavior qinqa-2nest top-most vlan-id 901 /外层vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外层vlan#traffic behavior qinqb-1nest top-most vlan-id 502 /外层vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外层vlantraffic behavior qinqb-3nest top-most vlan-id 1702 /外层vlan#traffic policy qinqaclassifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic policy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior qinqb-32、 定义外层vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 灵活qinq配置：（s9300主机版本为v100r002版本或业务单板最后一个字母非a的单板使用如下stacking配置灵活qinq）1、 定义外层vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port gigabitethernet1/0/1 masterport gigabitethernet1/0/2 slave timer wtr 30 /配置主端口恢复30s后恢复smart-link group 2protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port gigabitethernet1/0/2 masterport gigabitethernet1/0/1 slavetimer wtr 30 /配置主端口恢复30s后恢复#interface gigabitethernet1/0/1 /端口做为instance 1主用，instance 2备用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface gigabitethernet1/0/2 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段 业务调试验证命令display smart-link group 1模式二：链路捆绑+smart-link 灵活qinq配置：（s9300主机版本为v100r001版本或业务单板类型最后一个字母为a的单板使用如下流策略配置灵活qinq）1、 定义内层vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户vlantraffic classifier qinqa-2if-match vlan-id 43 /匹配itv用户vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itms终端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外层vlantraffic behavior qinqa-2nest top-most vlan-id 901 /外层vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外层vlan#traffic behavior qinqb-1nest top-most vlan-id 502 /外层vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外层vlantraffic behavior qinqb-3nest top-most vlan-id 1702 /外层vlan#traffic policy qinqaclassifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic policy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior qinqb-32、 定义外层vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 灵活qinq配置：（s9300主机版本为v100r002版本或业务单板最后一个字母非a的单板使用如下stacking配置灵活qinq）1、 定义外层vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port eth-trunk1 masterport eth-trunk2 slave timer wtr 30 /配置主端口恢复30s后恢复smart-link group 2protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port eth-trunk2 masterport eth-trunk1 slavetimer wtr 30 /配置主端口恢复30s后恢复#interface gigabitethernetx/x/x-01 /主用上行口-1eth-trunk1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-02 /主用上行口-2eth-trunk1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-03 /备用上行口-1eth-trunk2 /把端口加入link-aggregation group 2interface gigabitethernetx/x/x-04 /备用上行口-2eth-trunk2 /把端口加入link-aggregation group 2interface eth-trunk1 /端口做为instance 1主用，instance 2备用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface eth-trunk2 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段 业务调试验证命令display smart-link group 1display link-aggregation verbose模式三：单链路/链路捆绑+vlan双向透传 灵活qinq配置：（s9300主机版本为v100r001版本或业务单板类型最后一个字母为a的单板使用如下流策略配置灵活qinq）1、 定义内层vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户vlantraffic classifier qinqa-2if-match vlan-id 43 /匹配itv用户vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itms终端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外层vlantraffic behavior qinqa-2nest top-most vlan-id 901 /外层vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外层vlan#traffic behavior qinqb-1nest top-most vlan-id 502 /外层vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外层vlantraffic behavior qinqb-3nest top-most vlan-id 1702 /外层vlan#traffic policy qinqaclassifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic policy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior qinqb-32、 定义外层vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 灵活qinq配置：（s9300主机版本为v100r002版本或业务单板最后一个字母非a的单板使用如下stacking配置灵活qinq）1、定义外层vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50为dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702#interface gigabitethernetx/x/x-01 /上行口1port link-type trunk port trunk permit vlan 48 50 501 901 1701interface gigabitethernetx/x/x-02 /上行口2port link-type trunk port trunk permit vlan 49 501 901 1701 双网管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0为网络管理服务器段 业务调试验证命令display vlan x/x/x中兴t64g模式一：单链路+zess-link1. 板卡硬件要求：每台t64g至少配置1块ugsf板卡2. 软件版本要求：v2.8.01b19或v2.8.01c20以上3. 配置命令 全局配置stpspanning-tree enable /全局配置为stp enable，所有端口配置为stp disablespanning-tree mst configurationinstance 1 vlan 501,1701.901instance 2 vlan 502,1702.902 端口配置interface gei_1/1 /下行customer-port配置 switchport mode hybrid switchport hybrid native vlan 501 /见注意事项1 switchport hybrid vlan 50 tag switchport hybrid vlan 901 untag switchport hybrid vlan 1701 untag switchport qinq customer /定义端口为c口spanning-tree disable /关闭stpinterface gei_1/2 /下行customer-port配置 switchport mode hybrid switchport hybrid native vlan 502 /见注意事项1 switchport hybrid vlan 50 tag switchport hybrid vlan 902 untag switchport hybrid vlan 1702 untag switchport qinq customer /定义端口为c口 spanning-tree disable /关闭stpinterface gei_1/24 /上行uplink-port配置 switchport mode hybridswitchport hybrid native vlan 48switchport hybrid vlan 48 tag switchport hybrid vlan 50 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tagswitchport hybrid vlan 901-902 tag switchport hybrid vlan 2 untag switchport qinq uplink /定义端口为u口spanning-tree disable /关闭stpinterface gei_2/24 /上行uplink-port配置 switchport mode hybridswitchport hybrid native vlan 49 switchport hybrid vlan 49 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tagswitchport hybrid vlan 901-902 tag switchport qinq uplink /定义端口为u口spanning-tree disable /关闭stp session设置vlan qinq sessi