PRC-激光器报警(中文).doc

FLT_FLOW_TOO_LOW Laser Coolant Flow Is Below The Fault Level(激光器冷却水水流量低)FLT_FLOW_ON_TIMEOUT Laser Coolant Has Not Started Within The Allowed Time（激光器冷却水未在规定时间内打开）FLT_TEMP_COOLANT_IN Coolant Temperature Has Exceeded The Fault Level（冷却水温度超出设定范围）FLT_TEMP_SHUTTER_MIR_1 Shutter Mirror Temperature In Shutter 1 Has Exceeded The Fault Level（光闸反射镜1温度超出设定范围）FLT_TEMP_BEAM_DUMP_1 Shutter Beam Dump Temperature In Shutter 1 Has Exceeded The Fault Level（光闸吸收体温度超出设定范围）FLT_TEMP_TRB_1_CASE Turbine 1 Housing Temperature Has Exceeded The Fault Level（涡轮机1壳体温度超出设定范围）FLT_TEMP_TRB_1_BRNG_A Turbine 1 Bearing A Temperature Has Exceeded The Fault Level（涡轮机1轴承A温度超出设定范围）FLT_TEMP_TRB_1_BRNG_B Turbine 1 Bearing B Temperature Has Exceeded The Fault Level（涡轮机1轴承B温度超出设定范围）FLT_TEMP_TRB_2_CASE Turbine 2 Housing Temperature Has Exceeded The Fault Level（涡轮风机2壳体温度超出设定范围）FLT_TMEP_TRB_2_BRNG_A Turbine 2 Bearing A Temperature Has Exceeded The Fault Level（涡轮机2轴承A温度超出设定范围）FLT_TEMP_TRB_2_BRNG_B Turbine 2 Bearing B Temperature Has Exceeded The Fault Level（涡轮机2轴承B温度超出设定范围）FLT_TEMP_TRB_3_CASE Turbine 3 Housing Temperature Has Exceeded The Fault Level（涡轮风机3壳体温度超出设定范围）FLT_TEMP_TRB_3_BRNG_A Turbine 3 Bearing A Temperature Has Exceeded The Fault Level（涡轮机3轴承A温度超出设定范围）FLT_TEMP_TRB_3_BRNG_B Turbine 3 Bearing B Temperature Has Exceeded The Fault Level（涡轮机3轴承B温度超出设定范围）FLT_TEMP_RESONATOR_GAS Resonator Gas Temperature Has Exceeded The Fault Level（谐振腔气体温度超出设定范围）FLT_TEMP_MODULATOR_OIL Modulator Oil Temperature Has Exceeded The Fault Level (Only on Lasers with tube type HV Power Supplies) （油箱温度超出设定范围）FLT_REGULTNG_PRES_HI Laser Cavity Regulating Pressure Is Above The Fault Level（腔压高）FLT_REGULTNG_PRES_LO Laser Cavity Regulating Pressure Is Below The Fault Level（腔压低）FLT_BACKFILL_TIME_OUT Laser Backfill Has Failed To Complete In The Allowed Time（回充超时）FLT_HE_LO Helium Inlet Pressure Is Below The Fault Level AND Gas Fault Pre-Warning Time Has Expired（氦气压力低）FLT_CO2_LO CO2 Inlet Pressure Is Below The Fault Level AND Gas Fault Pre-Warning Time Has Expired（二氧化碳压力低）FLT_N2_LO Nitrogen Inlet Pressure is Below The Fault Level AND Gas Fault Pre-Warning Time Has Expired（氮气压力低）FLT_AIR_LO Air Inlet Pressure is Below The Fault Level. （空气压力低）FLT_DIS_OVER_CURRENT Current In Resonator Discharge Tube Has Exceeded Fault Level（放电电流过流）FLT_INV_UP2SPEED_TMOUT Inverter Has Failed to Reach Operating Frequency In Allowed Time（变频器在容许的时间内没有达到工作频率）FLT_INV_NOT_UP2SPEED Inverter Operating Frequency Is Below Required Minimum（变频器工作频率低于所需的最低）FLT_INV_FAULTED Inverter Is In Faulted Condition（变频器故障）FLT_VACUUM_PUMP_OVERLD Vacuum Pump Overload Breaker Has Tripped（真空泵断路器过载）FLT_COMPRESSOR _CB_AUX Compressor Circuit Breaker Auxillary Contact Has Tripped（涡轮风机断路器跳闸）FLT_VACUUM_PUMP _CB_AUX Vacuum Pump Circuit Breaker Auxillary Contact Has Tripped（真空泵断路器跳闸）FLT_HV _CB_AUX High Voltage Power Supply Circuit Breaker Auxillary Contact Has Tripped（高压断路器跳闸）FLT_HVPS_CONT_ON_TMOUT High Voltage Power Supply Control Contactor Has Failed to Energize/De-Energize In Allowed Time（在允许的时间内高压电源接触器没有吸合）FLT_ENCL_INTER_LOCK Laser Enclosure Interlock Is In Open State（激光器外壳联锁处于打开状态）FLT_HV_INTER_LOCK HV Safety Interlock is In Open State（激光器高压安全连锁报警）FLT_SHUTTER_1_SW_FAILED Position Switch In Shutter 1 Has Failed（光闸位置开关1出错）FLT_SHUTTER_1_LOST_POS Shutter 1 is in Neither Open Nor Closed Positions（光闸位置开关1既不开也不关反正有问题了）FLT_SHUTTER_1_NOT_OPEN Shutter 1 Failed To Open（光闸1打开失败）FLT_SHUTTER_1_NOT_CLOSE Shutter 1 Failed To Close（光闸1关闭失败）FLT_SHUTTER_2_SW_FAILED Position Switch In Shutter 2 Has Failed(Dual Beam Lasers Only) （光闸位置开关2出错）FLT_SHUTTER_2_LOST_POS Shutter 2 is in Neither Open Nor Closed Positions(Dual Beam Lasers Only) （光闸位置开关2既不开也不关反正有问题了）FLT_SHUTTER_2_NOT_OPEN Shutter 2 Failed To Open(Dual Beam Lasers Only) （光闸开关2打开失败）FLT_SHUTTER_2_NOT_CLOSE Shutter 2 Failed To Close(Dual Beam Lasers Only) （光闸开关2关闭失败）FLT_FS24V_TIMEOUT Fail Safe 24V Relay Did Not Close in Allowed Time（安全24V超时）FLT_PUMP_DOWN_TIMEOUT Laser Pump Down Did Not Complete in Allowed Time（回抽超时）FLT_HVPS_FAULTED A High Voltage Power Supply is in Faulted State（高压电源错误）FLT_HVPS_TUBE_OUT One of the Laser Discharge Tubes has Failed to Reach Minimum Discharge Current Level. （一个放电管没有达到最小放电电流）FLT_SNR_SHUTTER MIR_1 Temperature Sensor on Shutter 1 Mirror Has Failed. （光闸反射镜1温度报警）FLT_SNR_BEAM_DUMP_1 Temperature Sensor on Shutter 1 Beam Dump Has Failed. （光束套管1温度报警）FLT_SNR_SHUTTER MIR_2 Temperature Sensor on Shutter 2 Mirror Has Failed. (Dual Beam Lasers Only) （光闸反射镜2温度报警）FLT_SNR_BEAM_DUMP_2 Temperature Sensor on Shutter 2 Beam Dump Has Failed. (Dual Beam Lasers Only) （光束套管1温度报警）FLT_RESERVED_53 Reserved for Future Use（为将来使用保留）FLT_RESERVED_54 Reserved for Future Use（为将来使用保留）FLT_RESERVED_55 Reserved for Future Use（为将来使用保留）FLT_RESERVED_56 Reserved for Future Use（为将来使用保留）FLT_RESERVED_57 Reserved for Future Use（为将来使用保留）FLT_RESERVED_58 Reserved for Future Use（为将来使用保留）FLT_RESERVED_59 Reserved for Future Use（为将来使用保留）FLT_RESERVED_60 Reserved for Future Use（为将来使用保留）FLT_RESERVED_61 Reserved for Future Use（为将来使用保留）FLT_RESERVED_62 Reserved for Future Use（为将来使用保留）FLT_RESERVED_63 Reserved for Future Use（为将来使用保留）WRN_FLOW_TOO_LO Coolant Flow Is Below Warning Level（冷却水流量低报警）WRN_CDRH_FAIL CDRH Indicator Light Has Failed（CDRH指示等出错）WRN_TEMP_H2O_IN Coolant Inlet Temperature has Exceeded Warning Level（冷却水温度报警）WRN_TEMP_SHTR_MIR_1 Shutter 1 Mirror Temperature Has Exceeded Warning Level（光闸反射镜1温度报警）WRN_TMEP_BEAM_DMP_1 Shutter 1 Beam Dump Temperature Has Exceeded Warning Level（Shutter Beam Dump1温度报警）WRN_TEMP_SHTR_MIR_2 Shutter 2 Mirror Temperature Has Exceeded Warning Level (Dual Beam Lasers Only) （反射镜2温度报警）WRN_TMEP_BEAM_DMP_2 Shutter 2 Beam Dump Temperature Has Exceeded Warning Level (Dual Beam Lasers Only) （Shutter Beam Dump2温度报警）WRN_TEMP_TRB_1_CASE Turbine 1 Housing Temperature Has Exceeded Warning Level（涡轮机1机体温度报警）WRN_TEMP_TRB_1_BRNG_A Turbine 1 Bearing A Temperature Has Exceeded Warning Level（涡轮机1轴承A温度报警）WRN_TEMP_TRB_1_BRNG_B Turbine 1 Bearing B Temperature Has Exceeded Warning Level（涡轮机1轴承B温度报警）WRN_TEMP_TRB_2_CASE Turbine 2 Housing Temperature Has Exceeded Warning Level（涡轮机2机体温度报警）WRN_TEMP_TRB_2_BRNG_A Turbine 2 Bearing A Temperature Has Exceeded Warning Level（涡轮机2轴承A温度报警）WRN_TEMP_TRB_2_BRNG_B Turbine 2 Bearing B Temperature Has Exceeded Warning Level（涡轮机2轴承B温度报警）WRN_TEMP_TRB_3_CASE Turbine 3 Housing Temperature Has Exceeded Warning Level（涡轮机3机体温度报警）WRN_TEMP_TRB_3_BRNG_A Turbine 3 Bearing A Temperature Has Exceeded Warning Level（涡轮机3轴承A温度报警）WRN_TEMP_TRB_3_BRNG_B Turbine 3 Bearing B Temperature Has Exceeded Warning Level（涡轮机3轴承B温度报警）WRN_TEMP_RESONATOR_GAS Resonator Gas Temperature Has Exceeded The WarningLevel（谐振腔气体温度报警）WRN_TEMP_MODULATOR_OIL Modulator Oil Temperature Has Exceeded Warning Level (Only on Lasers that are Equipped with Tube Type HVPS) （油箱温度）WRN_SNR_COOLANT_IN CoolantTemperature Sensor Has Failed（冷却水温度传感器温度错误）WRN_SNR_SHUTTER_MIR_1 Shutter1 Mirror Temperature Sensor Has Failed（光闸反射镜1温度传感器错误）WRN_SNR_BEAM_DUMP_1 Shutter 1 Beam Dump Temperature Sensor Has Failed（Shutter Beam Dump1温度传感器错误）WRN_SNR_SHUTTER_MIR_2 Shutter 2 Mirror Temperature Sensor Has Failed(Dual Beam Lasers Only) （光闸反射镜2温度传感器错误）WRN_SNR_BEAM_DUMP_2 Shutter 2 Beam Dump Temperature Sensor Has Failed(Dual Beam Lasers Only) （Shutter Beam Dump2温度传感器错误）WRN_SNR_TRB_1_CASE Turbine 1 Case Temperature Sensor Has Failed（涡轮机1温度传感器错误）WRN_SNR_TRB_1_BRNG_A Turbine 1 Bearing A Temperature Sensor Has Failed（涡轮机1轴承A温度温度传感器错误）WRN_SNR_TRB_1_BRNG_B Turbine 1 Bearing B Temperature Sensor Has Failed（涡轮机1轴承B温度传感器错误）WRN_SNR_TRB_2_CASE Turbine 2 Case Temperature Sensor Has Failed（涡轮机2温度传感器错误）WRN_SNR_TRB_2_BRNG_A Turbine 2 Bearing A Temperature Sensor Has Failed（涡轮机2轴承A温度温度传感器错误）WRN_SNR_TRB_2_BRNG_B Turbine 2 Bearing B Temperature Sensor Has Failed（涡轮机2轴承B温度传感器错误）WRN_SNR_TRB_3_CASE Turbine 3 Case Temperature Sensor Has Failed（涡轮风机3温度传感器错误）WRN_SNR_TRB_3_BRNG_A Turbine 3 Bearing A Temperature Sensor Has Failed（涡轮机3轴承A温度温度传感器错误）WRN_SNR_TRB_3_BRNG_B Turbine 3 Bearing B Temperature Sensor Has Failed（涡轮机3轴承B温度传感器错误）WRN_SNR_MOD_OIL Modulator Oil Temperature Sensor Has Failed(Only on Lasers that are Equipped with Tube Type HVPS) （油箱温度传感器错误）WRN_HE_LO Helium/Premix Inlet Pressure is Below Fault Level（氦气压力报警）WRN_CO2_LO CO2 Inlet Pressure is Below Fault Level（二氧化碳压力报警）WRN_N2_LO Nitrogen Inlet Pressure is Below Fault Level（氮气压力报警）WRN_AIR_LO Air Purge Inlet Pressure is Below Fault Level（空气压力报警）WRN_INV_FAULT Frequency Inverter is in Fault State During PUMPDOWN Sequence. （回抽时变频器错误）WRN_HVPS_FAULT High Voltage power supply is in a faulted condition. （高压电源错误）WRN_SHUTTER _1_FAULT High Voltage Has Been Initiated With Shutter 1 In Fault State（高压启动后光闸1错误）WRN_SHUTTER _2_FAULT High Voltage Has Been Initiated With Shutter 2 In Fault State（高