外文.pdf_第1页
外文.pdf_第2页
外文.pdf_第3页
外文.pdf_第4页
外文.pdf_第5页
已阅读5页,还剩2页未读, 继续免费阅读

外文.pdf.pdf 免费下载

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

International Journal of Automotive Technology, Vol. 10, No. 1, pp. 8793 (2009) DOI 10.1007/s1223900900117 Copyright 2009 KSAE 12299138/2009/04411 87 DESIGN OF CONFORMAL COOLING CHANNELS FOR AN AUTOMOTIVE PART H. S. PARK* and N. H. PHAM School of Mechanical and Automotive Engineering, University of Ulsan, Ulsan 680-749, Korea (Received 20 June 2008; Revised 24 September 2008) ABSTRACTThe cooling system plays a crucial role in determining the productivity and quality of an injection molding process. With the current growth of Solid Freeform Fabrication (SFF) techniques, mold designers have been striving for not only improvement in cooling system performance but also for a method to do so automatically. In this paper, a method is proposed for developing a conformal cooling system that facilitates uniform cooling over the entire mold surface with minimum cycle time. Based on the temperature distribution after the filling stage, the mold surface is split into zones which will be cooled by optimized subconformal channels obtained from the optimization process. The optimization process in which the objective function is stated as minimization of the cooling time with boundaries ensuring a realistic design will optimize the cooling system layout in terms of cooling channel size and location. Finally, all subcooling channels are combined to generate the entire conformal cooling system for the injection mold. KEY WORDS : Injection mold, Conformal cooling channel, Optimization, Cooling time NOMENCLATURE QKS : heat flux from molding, kJ/m QE: heat exchange with the environment, kJ/m QC: heat exchange with the coolant, kJ/m tC: cooling time, s s: part thickness, mm a: distance between two cooling channels, mm b : distance from the mold surface to the center of the cooling channel, mm dC: diameter of cooling channel, mm TM: mold temperature, oC TE: demolding temperature, oC im: latent heat of fusion of polymer, kJ/kg cpm: specific heat of the melt, kJ/(kg oC) m: melt density, g/cm3 m: thermal conductivity of the melt, W/(moC) Twater: temperature of coolant, oC TW: mold wall temperature, oC ST: thermal conductivity of mold steel, W/(moC) Se: shape factor : heat transfer coefficient 1. INTRODUCTION Plastic injection molding has been used increasingly in recent years due to high productivity in creation of prod- ucts with various shapes and complex geometry at low cost. The injection molding process includes three impor- tant stages, the filling stage, packing stage, and cooling stage (Lin, 2002). Among these stages, the cooling stage is of great importance because it significantly affects produc- tivity and quality of the final part (Tang et al., 1997). More than 70% of the molding cycle time is taken up by the cooling stage. An efficient cooling system design aimed at reducing cycle time must minimize undesired defects such as sink marks, differential shrinkage, thermal residual stress build-up, and part warpage. In previous work, many com- puter-aided-engineering (CAEs) and optimization methods have been applied to observe and fine-tune the influences of the thermal system. The results of this body of research are mainly obtained by using thermal analysis modules from commercial CAE packages such as C-MoldTM or MoldflowTM. These analyses are based on the initial designs generated by individual designers experiences. However, those designs do not always give good results as part geo- metry becomes more and more complicated. Conventionally, the mold surface temperature is consi- dered to be constant although there is a heat distribution on the mold surface caused by hot material running into the cavity. This leads to not only a difference between the simulation results and the real injection molding process, but also a non-unique cooling surface if the same cooling channel configuration is utilized. Furthermore, cooling system design and fabrication have been confined to relatively simple configurations, primarily due to the limits of the fabrication methods as well as the lack of appropriate design methodology. A proposed solution to this challenge is a rapid thermal response molding process carried out with a conformal cooling system (Li, 2001). A conformal*Corresponding author. e-mail: phoskulsan.ac.kr 88H. S. PARK and N. H. PHAM cooling channel, as the name implies, refers to channels that conform to the surface of the mold cavity. These channels, which can be successfully fabricated with the Solid Freeform Fabrication process, have demonstrated simultaneous improvement in production rate and part quality as compared with conventional production tools (Xu et al., 2001). Accordingly, the remaining problems to be considered in terms of cooling system design and processing conditions during the cooling stage of the injection molding process are as follows: (a) minimization of cooling time and (b) achievement of uniform cooling (i.e., the temperature must be kept constant at all points on the mold surface). In this paper, the heat transfer problem in injection molding is first analyzed. Based on the temperature distri- bution after the filling stage, the mold surface is split into appropriate zones. These zones will be cooled by optimi- zed subconformal channels derived from the optimization process in order to obtain unique cooling on the mold surface. The objective function in the optimization process is stated as minimization of the cooling time, and the design variables chosen are cooling channel size and location. Finally, these subconformal cooling sets are combined to create the entire conformal cooling channel system for the injection mold. 2. PHYSICAL MODELING In the physical sense, the cooling stage involves very complicated issues. To simplify the process, the following assumptions are made in this study: Because changes in the physical properties of mold materials caused by temperature and pressure are not significant, they are considered as constant. During the initial stage, both the mold and the plastic material are assumed to have their own uniform temper- atures, and the plastic material is assumed to contain no solid parts. The inner pressure of the mold cavity is assumed con- stant. Thus, the volume of plastic materials remains con- stant during the solidification process. The most important basis for calculating the heating system of a mold is its heat balance because the mold temperatures for elastomers and thermosets are 100150oC higher than for thermoplastics. When a heat balance is established for molds and thermoplastics at higher temper- atures, an energy balance will be set up by considering the heat fluxes for the quasi-steady state of the operation. In the quasi-steady state, heat flux supplied to the mold (counted as positive) and the heat flux removed from the mold (counted as negative) must be in equilibrium. The heat flux balance is as follows: QKS+QE+QC=0 (1) The heat of the molten polymer is taken away by the coolant moving through the cooling channels and by heat exchange with the environment. The coolant flow through the channels with a certain flow-rate and the temperature at the inlet of the cooling channels is pre-assigned. Heat exchange takes place by forced convection between the coolant and the cooling channel surface together with the heat exchange with the environment. This environmental heat exchange consist mainly of the natural convection between the ambient air and the exterior mold surface (Menges et al., 2001). The exterior surface is considered as adiabatic because the heat loss through this surface is less than 5% of the overall loss in most injection molding applications (Park and Kwon, 1998). This approximation simplifies the problem and at the same time, points to the fact that 95% of the heat of the molten polymer must be removed by the coolant passing through the cooling channels. Finally, the heat exchange is considered as solely the heat exchange between the molten polymer and the coolant. QKS+QC=0 (2) According to Rao et al. (2002), the heat flux from the molten polymer to the cooling media can be expressed as: (3) The heat flux exchange with the coolant in the cooling time tC amounts to: (4) TW is the mold wall temperature right after the filling stage is completed. This temperature can be obtained by experimental or simulation results. The shape of the cooling channels also has an influence on the heat conduction effect and it is taken into account by the shape factor Se (Thorne, 1997). In this paper, the shape of the cooling channels is conventionally chosen as cir- cular. Accordingly, the shape factor Se is: (5) QKS=TMTE()cpmim+m s 2 - -a10 3 QC=tC 1 STSe - - 1 10 3 dC -+ 1 TWTwater()10 3 Se= 2 ln 2asinh 2b /a() dC - - - - Figure 1. Physical modeling and sketch of the cooling system. DESIGN OF CONFORMAL COOLING CHANNELS FOR AN AUTOMOTIVE PART89 Using the values for the properties of water, the heat transfer coefficient is as follows (Rao, 1991): (6) The Reynolds number can be calculated as follow: (7) In this case, due to the change in the diameter of the cooling line, the velocity of water is adjusted to keep the Reynolds number constant for ease in calculation. 3. OPTIMIZATION STRATEGY Due to the difference in the temperature distribution over the mold surface after the filling stage, one cooling con- figuration is not suitable for the whole mold. In order to increase the evenness of the cooled surface temperature, the mold surface is split into zones which will be cooled by subconformal cooling channels based on the temperature distribution varied from the minimum to maximum values. Parameters for developing subconformal cooling channels are obtained with the optimization process mentioned below. In this paper, the optimization process is individually applied for each separate split cooling zone. The objective function was defined by the cooling time with respect to the cooling line locations and their radii as the design variables. To work towards the design goal of cooling channel system, the objective function of the cool- ing time is chosen by combining equations from (2) to (7) as follows: min (8) Proper constraints must be also considered on all the design variables to keep the design realistic and assure part quality. In this problem, upper and lower boundaries must be placed on the positions and radi of each cooling channel not only to keep the design realistic from a manufacturing view point but also to keep the strength of the injection mold in a swnsible range as well. Inequality constraints in association with design variables having upper and lower boundaries are expressed by: (9) This constrained optimization problem can be easily solved by several optimization algorithms such as Response Surface Method, Simulated Annealing, Genetic Algorithms, among others. In this study, the results are obtained from solving the generated numerical model. A Matlab program is developed to calculate values of the cooling time from each set of the parameters within the inequality constraints mentioned above. From these calculations, the optimized cooling time can be achieved together with required values of parameters. Through solving the above optimization problem, we can reduce the cooling time by adjusting the characteristics of each design variable as follows: (1) The distance from the mold surface to the center of the cooling channel decreases. (2) The distance between two cooling channel decreases. (3) The diameter of the cooling channel increases. As in the results mentioned above, the distance from the mold surface to the center of the cooling channel and the distances between cooling channels should be chosen as minimum, while the diameters of the cooling channel should be chosen as maximum. These parameters must make up a unique set of parameters in order to obtain the best results in the cooling stage, because one minimum or maximum value of a parameter cannot be a good choice. For example, the smaller the distance from the mold surface to the center of the cooling channel, the more rapidly the heat is removed and the shorter the cooling time. Nevertheless, the resulting cavity surface temperature variation can lead to part-quality problems due to inapprop- riate distance between two cooling channels. Based on the previous experience and engineering analysis, these para- meters should be chosen as follows: (10) Furthermore, the parameters of each of the subconformal cooling channels must be chosen so that all of them result in exactly the same minimum cooling time. The optimization process for determining the values of the parameters is presented in Figure 2. Initially, para- meters related to the characteristics of the mold and plastics material such as the latent heat of fusion of the polymer, the melting temperature of the polymer, specific heat of the melt, melt density, thermo-conductivity of the melt, thermal conductivity of mold steel, initial mold wall temperature and the shape factor of the plastic product are input. In the next step, a filling stage simulation is run with commercial analysis software to obtain the heat distribution. Although the temperature at the position of the runner gate is higher (in case the hot runner is used), the mold wall temperature is conventionally considered to be constant while calcu- lating the processed of heat transfer and cooling time. However, in order to attain a more exact cooling time and unique cooling zones, the difference in temperature distri- bution must be taken into account. The location that has the higher temperature should have the ability to dissipate =0.031395 dC - -Re0.8 Re=u dC - - tCa,b,dC()= TMTE()cpmim+m s 2 - -a TWTwater - - 1 2ST - -ln 2 asinh 2b /a() dC - - + 1 0.031395Re0.8 - - min dC()dCmax dC () min a( )amax a( ) min b( )bmax b( ) 6mmdC12mm 2dCa5dC dCb5dC 90H. S. PARK and N. H. PHAM more heat, which means it must have a different cooling configuration. Accordingly, the plastic product is split into smaller parts based on the temperatures ranging from the smallest to the largest values obtained from the previous step. The more finely the temperature ranges are divided, the more uniform the cooling zones are divided as well. For each divided temperature range, the average temperature is used as the mold wall temperature TW. This mold wall temperature is one of the main parameters used to calculate the cooling configuration in Equation (8). Next, the objec- tive function for minimum cooling time is solved with the constraints. For each mold material, there will be a sug- gestion for the lower and upper boundaries in the form of equation (10). This optimization problem can be solved by any engineering optimization tool. The process ends with parameters a, b, dC for each of the divided cooling zones and is then repeated for each of the divided parts. 4. SHAPES OF THE CONFORMAL COOLING CHANNELS Rapid cooling improves process economics, whereas uni- form cooling contributes to product quality by preventing differential shrinkage, internal stresses, and mold release problems. Both rapid and uniform cooling is achieved by a sufficient number of properly located cooling channels. Fluid passages for effective mold and part cooling should be carefully placed to cover most of the molding surface. The shape of the cooling channels is also one of the most significant factors in deciding the effectiveness of the systems. In conventional molding techniques, in the case in which the plastic part is large or there are several cores to be cooled simultaneously, the two most commonly used cooling systems are cooling in series and parallel cooling. Athough a part may have a circular form, cooling channels in series have been used in practice. The basic form, i.e., parallel and series, of a traditional cooling system can be applied to a conformal cooling channel after being appro- priately modified. In this paper, we present three types of conformal cool- ing systems based on the conventional types with modifi- cations to retain the conformal properties; these include the conformal zigzag type, conformal parallel type and con- formal spiral type, as shown in Figure 5. With conformal zigzag types, the individual parts of the product are sup- plied with coolant one after the other. Since the temperature differences between the molding and the coolant decrease with the increasing flow length of the coolant, uniform cooling of the cores is not provided. Consequently, this type should only be used if the plastic part is not too large. In order to avoid this situation, parallel cooling is em- ployed. With parallel cooling, the individual cores are sup- plied with coolant from a main channel and another collecting channel removes the coolant. Thus, each core is fed with coolant of the same temperature. This provides for a uniform cooling, but a large volume of coolant will be used. Furthermore, the spiral cooling pattern that can be used to cool circular parts can also be modified for use in a conformal cooling system. The coolant flows from edge to the center in the spiral pattern. The temperature of the coolant increases as it flows through the spiral, while the melt has already cooled down some degree because of the length of its flow. With the SFF technique, these conformal cooling systems give better cooling results when compared to the original ones because the distance between the cooling channels and the mold surfaces are always kept constant, which results in more uniform cooling. Each

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论