已阅读5页,还剩5页未读, 继续免费阅读
粉末注射成型的流程模拟充模过程中主要参数的区别.pdf.pdf 免费下载
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
Process simulation of powder injection moulding: identification of significant parameters during mould filling phase S. V. Atre*1, S.-J. Park2, R. Zauner3and Randall M. German2 Simulating and optimising the powder injection process are complex problems since a number of linked material, geometry and process variables have to be considered. In addition, it is very difficult to identify critical parameters for designing binder systems, feedstocks, parts, moulds and processing conditions owing to the fact that multiple objective functions have to be considered. Towards the goal of identifying the level of significance of various material, process and geometry parameters during powder injection moulding, a systematic procedure for sensitivity analysis has been successfully developed for the mould filling phase of the PIM process. In this sensitivity analysis, all input parameters were defined for the mould filling simulation and all output parameters for optimum design of part, mould and processing conditions and dimensionless sensitivity values for all input and output parameters were calculated, which allow parameters with different units to be compared quantitatively. The sensitivity analysis procedure developed will be an invaluable tool for both the design engineer in the PIM industry who has to determine the critical input parameters for given design targets, as well as for the production engineer who has to optimise and monitor the production stage. Keywords: Powder injection moulding, Computer simulation, Mould filling, Sensitivity analysis List of symbols and abbreviations Bamplitude coefficient in feedstock viscosity model BPbinder properties Bbamplitudecoefficientinbinderviscosity model cpspecific heat capacity of feedstock cp,bspecific heat capacity of binder Ccoefficient for transient region in feedstock viscosity model fcclamping force FPfeedstock properties GCgeometric component GDgate diameter kthermal conductivity of feedstock kbthermal conductivity of binder mpower law exponent in slip layer model npower law exponent in feedstock viscosity model piinjection pressure PCprocessing conditions PTpart thickness RDrunner diameter SDsprue diameter SOswitch over point tccooling time tffilling time tppacking time Ttemperature TbArrhenius type coefficient in feedstock visc- osity model Tb,bArrhenius type coefficient in binder viscosity model Teeject temperature of feedstock Tgglass transition temperature of feedstock Tiinjection temperature Twmould wall temperature aamplitude coefficient in slip layer model bArrhenius type coefficient in slip layer model : cshear rate : cmaxmaximum shear rate at mould wall dslip layer thickness gfeedstock viscosity gbbinder viscosity g0zero shear rate viscosity in feedstock viscos- ity model mMFAaverage of melt front area mMFVaverage of melt front velocity 1Oregon Nanoscience and Microtechnologies Institute, Oregon State University Corvallis, OR 97331, USA 2Center for Advanced Vehicular Systems, Mississippi State University, PO Box 5405, Mississippi State, MS 39762, USA 3Materials Research,ARCSeibersdorfresearchGmbH,A2444 Seibersdorf, Austria *Corresponding author, email 76 ?2007 Institute of Materials, Minerals and Mining Published by Maney on behalf of the Institute Received 17 February 2006; accepted 26 July 2006 DOI 10.1179/174329007X185607Powder Metallurgy2007VOL50NO1 rdensity of feedstock rbdensity of binder sMFAstandard deviation of melt front area sMFVstandard deviation of melt front velocity tmaxmaximum shear stress at mould wall twshear stress at mould wall tyyield stress in feedstock viscosity model DMFTmelt front temperature difference Introduction In recent times, powder injection moulding (PIM) has been increasingly recognised as a viable and established technology for the net shape production of small, intricate,precisionmetalandceramiccomponents. Powder injection moulding is used in an increasing range of different fi elds, including automotive, medical andtelecommunicationsindustries.1Owingtothe complexity of the PIM process, it has long been considered more as an art than a science, but nowadays a number of feedstock and equipment suppliers serve as a support network for potential users and help them get started. Expensive and time consuming trial and error methods continue to be widely used to resolve design problems associated with raw material, product, tool and process issues during manufacturing with PIM. A causal relationship between input and output para- meters is often not straightforward. In the past, designed experiments have been carried out to fi nd empirical relationships for the infl uence of feedstock properties, processing conditions and mould properties on the mould fi lling behaviour, defect formation and dimen- sional variability of injection moulded components.29 The recent availability of computer aided engineering (CAE) design tools for PIM has shown some promise for aiding the engineer to resolve the interrelated problems involving material process geometry at an early stage in the design cycle. A signifi cant problem with using CAE design tools is the need for reliable material property data for running the simulations. The important properties relate to rheological,10thermal11and equation of state para- meters12associated with the feedstock and the binder. Although well established methods do exist for measur- ing the relevant material properties, they are often expensive. The material properties typically depend on changes in temperature and pressure.13Frequently, even if experimental measurements are made, the data is available for only part of the temperature pressure domain of interest. Further, variations in feedstock formulations and homogeneity can result in changes in material properties.14,15Therefore, adjustments have to be made to the material property estimates in order to improvetheaccuracyofthedesignpredictions. Numerous semiempirical scaling rules are available to estimate material properties to account for changes in composition,temperatureandpressurevariables.16 There can however be considerable scatter in the material property values estimated in this manner from different scaling rules. However, little information is available on the sensitivity of various predictions of CAE design tools to variations in the material property values. A large number of material parameters are embedded into the predictive equations used in the simulation procedures in a typical CAE design tool. An importantquestionthenarisespertainingtohow variations in material property estimates infl uence the errorsarisinginpredictionsofvarioussimulated parameters. During the design of a component, adjustments can be made to the dimensions of the component in order to improve the functional and aesthetic attributes of the part. Additionally, changes can be made to the location and dimensions of the melt delivery system to improve the manufacturability of the component. These issues also raise questions as to how small changes in product andtooldimensions infl uenceprocessvariations. Finally, several process settings can be changed and controlled by the operator on the injection moulding machine during the production stage. It is important to understandhowaCAEdesigntoolcapturesthe infl uence of such process variations in its predictions. The present study addresses the above crucial ques- tions by analysing the mould fi lling stage of the PIM process for the fi rst order sensitivity of selected material, geometry and process variables to several process related output variables of a CAE design tool, PIMSolver (Cetatech, Inc.). The results provide important insights intotherequiredaccuracyindeterminingvarious material properties. Further, quantitative relationships on the dependence of many PIM process variables on changes in component and tool geometry as well as some typical injection moulding machine settings are presented. The important consequences of these fi ndings on the PIM industry are further discussed. Simulation of PIM process The commercially available software PIMSolver was used to carry out the simulations in the present study. PIMSolver utilises the hybrid method of fi nite element method (FEM) and fi nite difference method (FDM) for calculating the fl ow and temperature fi elds in defi ned geometries and has been specifi cally developed and experimentally validated for PIM simulation applica- tions.17Conventional plastic injection moulding and PIM involve materials with signifi cantly different feed- stock properties. Feedstocks for PIM often exhibit strongly temperature dependent viscosities, which can be a few orders of magnitude higher at the injection temperature than those of corresponding unfi lled poly- mers. Moreover, the thermal conductivity of feedstock is usually far higher than that of polymers, which leads to differences in temperature profi les, cooling times and heat management. These differences have to be con- sidered when simulating the PIM process.18The soft- ware is capable of simulating in two and half-dimension (2. 5D) and models the fl ow in the third dimension as fully developed. For the geometries chosen in the present study, this limitation has no signifi cant infl uence on the results as the cavities modelled do not have any step wise increase or decrease in thickness in the third dimension. Simulation procedure In the present study, two different component geome- tries were selected and simulated: a tensile bar (Fig. 1a) and a plate (Fig. 1b). For future validation experiments, moulds with exactly the same cavity and delivery geometries will be used. The mesh for each geometry was generated using the meshing tool of PIMSolver; meshindependenceofthesimulationresultswas Atre et al.Process simulation of powder injection moulding Powder Metallurgy2007VOL50NO177 checked before the sensitivity study. The simulations in the present study only focused on the mould fi lling stage of the PIM process. The packing and cooling stages of the PIM process have been analysed and will be reported separately. A baseline process with typical values for material and process parameters was defi ned based on experience. The input parameters for this baseline process have been divided into four subgroups: (i)process parameters (ii)component geometry parameters (iii)feedstock material properties (iv)binder material properties. The output parameters evaluated in the study were classifi ed into: (i)pressure related parameters (ii)temperature related parameters (iii)flow related parameters. The goal of this sensitivity analysis is to identify the input parameters that have the greatest infl uence on the output parameters. Input parameters Process parameters The input process parameters considered in the present study are listed in Table 4. These parameters are based on experience for a typical injection moulding process. It is noted that switch over point (SO) is set as a percentage of cavity volume fi lled and mould wall temperature can be obtained from mould cooling phase simulation. Component geometry parameters A detailed description of the dimensional attributes of the components used in the present study is shown in Fig. 1.Thevaluesoftheparametersselectedfor sensitivity analysis are presented in Table 2. It is noted that the cross-sectional shape of the gate in the tensile bar is a half circle, that there is no runner in the plate and that the sprues are tapered in both parts. Feedstock material properties The feedstock material properties were experimentally determined for 316L stainless steel with a powder loading of 53 vol.-% and are summarised in Table 3. The dependence of feedstock viscosity g, on shear rate c and temperature were modelled with the modifi ed cross- model, that accounts for the yield stress tyof the feedstock, using the following equations g g0 1zC g0:c1n z ty : c (1) where g0is the zero shear rate viscosity, n is a power law exponent and C is a coeffi cient describing the transition region from Newtonian behaviour to non-Newtonian behaviour. g0B exp Tb T ? (2) B is the amplitude coeffi cient and Tbis an Arrhenius type coeffi cient. Binder material properties The relevant material properties of the binder used in the present study are summarised in Table 4. The binder material properties were used in the simulations only in a bar; b plate 1Description of tensile components used for analysis Table 1Input data: process parameters Filling timetf1.0 s Switch over pointSO98% Injection temperatureTi130uC Mould wall temperatureTw35uC Table 2Input data: component geometry parameters PartTensile barPlate Part thickness, mmPT3.173.41 Gate diameter, mmGD 4 (half circle) 3.35 Runner diameter, mmRD 5 Sprue diameter (tapered), mm SD78.27 Table 3Input data of feedstock material properties Density r, kg m233975 Specific heat capacity cp, J kg21K685 Thermal conductivity k, W m21K1.84 Transition temperature Tg, uC52.4 Eject temperature Te, uC50 Viscosity n0.18 B, Pa s5.1961023 C, Pa(n21)1.1561024 Tb, K5370 ty, Pa100 Atre et al.Process simulation of powder injection moulding 78Powder Metallurgy2007VOL50NO1 a very restricted computational domain (typically, 1 10 mm) near the mould wall where powder binder separation leads to a high binder content. The remaining computational domain was simulated using feedstock material properties. The dependence of the binder viscosity gb, on temperature T, is described by gbBbexp Tb,b T ? (3) where Bb is the amplitude coeffi cient and Tb,bis an Arrhenius type coeffi cient, analogous to equation (2). The effect of non-zero wall velocity, which is called slip phenomena, was accounted for in a slip layer of thickness d, which depends on the wall shear rate twand temperature, as shown da exp bTtm w (4) where a is the amplitude coeffi cient, b is an Arrhenius type coeffi cient and m is the power law exponent. Output parameters As described earlier, the output process parameters were classifi ed into three categories and are listed in Tables 5 7. Their values are calculated based on the above input parameters, which are used for initial or reference values for sensitivity analysis. The meaning of each output parameter will be discussed in section on Results and discussion. Sensitivity analysis For the sensitivity analysis, the input parameters were varied over a fi xed range (5%) and the response of the output parameters was monitored. The sensitivity was calculated as the gradient or slope of the dimensionless dependent variable with respect to the dimension- less independent variable according to the following equation Sensitivity: percentage change in output percentage change in input : increment in output=initial value of output increment in input=initial value of input (5) This defi nition of sensitivity was used to compare input and output parameters having different dimensions. For example, a sensitivity value of 21.5 means that the percentage decrement of output is 1.5% if the percentage increment of input is 1.0% and is independent of the units of the input and output parameters. Results and discussion Simulations were performed varying the input para- meters described in the previous section. The simulation results are presented below for the individual output parameters, starting with the pressure related para- meters, then temperature related and fi nally fl ow related parameters. The signifi cance was termed strong at levels 1. 0 according to the defi nition above, medium in the range between 0.5 and 1.0 and weak at level ,0.5. Each set of output parameters is discussed in this section. Pressure related output parameters Injection pressure Flow of feedstock in a mould is pressure driven. The pressure at the injection nozzle rises as the mould cavity begins to fi ll and continues to do so until the switch over to packing pressure occurs. The maximum pressure at the nozzle when switch over occurs is called injection pressure, which is an important specifi cation of an injection moulding machine. Therefore, the size of an injection moulding machine can be selected based on the predictedinjection pressure. Improper specifi cation of the injection pressure can result in several types of defects in the moulded component. A mould cavity can be over packed, creating a fl ash or it can also be under packed, creating a short shot. Other mould fi lling problems includejettingandformationofweldlines.Consequently, minimum injection pressure, which is thedriving force for moulding, is best for a good part without a defect. Figure 2a and b summarises the sensitivity of the injection pressure towards the input parameters for the tensile bar and plate respectively. For the tensile bar the largest infl uence arises from variation in feedstock properties, specifi cally the feedstock viscosity para- meters n and Tbwith strong level and C with medium level (Fig. 2a). A high viscosity material in return will need a higher injection pressure to fi ll the part. These results emphasise the importance of a homogeneous feedstock for consistent moulding results. Variations in theprocessparametersSOwithstrongleveland injection temperature Ti, with medium level also cause signifi cant changes in the injection pressure. A delay in Table 4Input data of binder material properties Density rb, kg m23739 Specific heat capacity cp,b, J kg21K2286 Thermal conductivity kb, W m21K0.178 Viscosity Bb, Pa s5.7261023 Tb,b, K3652 Slip layer a, m2.3761029 b, K214.23261023 m0.5126 Table 5Output data: pressure related parameters PartTensile barPlate Injection pressure pi, MPa20.8435.66 Clamping force fc, ton0.3352.549 Maximum shear stress tmax, MPa0.2600.290 Table 6Output data: temperature related parameters PartTensile barPlate Melt front temperature difference DMFT, uC 5.1808.640 Packing time tp, s0.8780.618 Cooling time tc, s3.0733.559 Table 7 Output data: fl ow related parameters PartTensile bar P
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 初中生物九年级专题十四教学设计:植物体内物质与能量变化复习策略
- 高三物理电场性质教学设计
- 初中物理九年级《简单机械》中考复习教学设计
- 高三英语译林版必修三词汇短语与词形变换复习教学设计
- 小学三年级心理健康教案:认识独特的自己
- 小学六年级心理健康教学设计:正确表达情绪的智慧之旅
- 沪科版高中信息技术必修《信息技术基础》教学设计:第4章第2节计算机文件管理方案
- 2026事业单位工勤技能-新疆-新疆收银员五级(初级工)历年参考题库含答案详解
- 2026事业单位工勤技能-新疆-新疆动物检疫员四级(中级工)历年参考题库含答案详解
- 2026事业单位工勤技能-广西-广西造林管护工四级(中级工)历年参考题库含答案详解
- 肿瘤患者免疫治疗相关心肌炎诊疗
- 2025成都农业科技职业学院教师招聘考试题目及答案
- 2025年棉花加工辅助工三级安全教育(班组级)考核试卷及答案
- 精神科药物依从性管理
- 中小学以体育强化为核心落实“健康第一”教育理念实施方案
- 间羟胺药物课件
- 整县屋顶分布式光伏项目绿色施工方案
- GB/T 4337-2025金属材料疲劳试验旋转弯曲方法
- 输变电工程工程量清单计价规范宣贯材料
- 手术室精益管理汇报
- (重点)水利安全员B证近年考试真题题库-含答案
评论
0/150
提交评论