STCubeMX翻译.docx

ADC Configuration ADC配置Parameter Settings 参数设置NVIC Settings 中断优先级设置DMA Settings DMA模式设置GPIO Settings GPIO设置Configure the below parameters： 配置以下参数ADC Settings ADC设置Clock Prescaler 时钟分频 Asynchronous clock mode 不同步时钟模式 Synchronous clock mode divided by 2 同步时钟模式除以2Synchronous clock mode divided by 4 同步时钟模式除以4Resolution ADC采样分辨率 ADC 12-bit resolution ADC 12位采样分辨率ADC 10-bit resolution ADC 10位采样分辨率ADC 8-bit resolution ADC 8位采样分辨率ADC 6-bit resolution ADC 6位采样分辨率Data Alignment 数据对齐Right alignment 数据右对齐模式Left alignment 数据左对齐模式Scan Conversion Mode扫描转换模式 Forward 扫描通道从第一个通道到最后一个通道Backward 扫描通道从最后一个通道到第一个通道Continuous Conversion Mode连续转换模式Disabled 关闭Enabled 打开Discontinuous Conversion Mode间断转换模式Disabled 关闭Enabled 打开DMA Continuous RequestsDMA连续请求Disabled 关闭Enabled 打开End of Conversion Selection转换结束选择End of single conversion 单通道转换结束End of sequence of conversion 序列转换结束End of single or sequence of conversion单通道或序列结束Overrun behaviourOverrun data preservedOverrun data overwrittenLow Power Auto Wait低电压自动等待Disabled 关闭Enabled 打开Low Power Auto Power Off低电压ADC自动关闭Disabled 关闭Enabled 打开ADC_Regular_ConversionMode ADC规则通道转换模式Number Of Conversion 转换的通道个数External Trigger Conversion Edge外部触发转换边沿None 没有外部触发Trigger detection on the rising edge 上升沿触发检测Trigger detection on the rising edge 下降沿触发检测Trigger detection on the rising or fallings 上升沿和下降沿触发External Trigger Conversion Source 外部触发转换源Timer1 Trigger Out event 定时器1触发Timer1 Capture Compare4 event 定时器1输出比较4事件Timer3 Trigger Out event 定时器3触发输出事件Timer15 Trigger Out event 定时器15触发输出事件Software Trigger 软件触发转换Rank 转换序列号Watchdog 看门狗Enable Analog WatchDog Mode 打开模拟看门狗Watchdog Mode Single regular channel 单一规则通道上打开看门狗All regular channel 所有规则通道上打开看门狗None 关闭看门狗High Threshold 看门狗高临界值Low Threshold 看门狗低临界值Interrupt Mode 中断模式Disabled 关闭Enabled 打开ADC global interrupt ADC 全局中断TIM1 Configuration TIM1 配置Prescaler 时钟分频数Counter Mode计数模式 UP 向上计数Down 向下计数Center Aligned mode1 中间对齐模式1Center Aligned mode2 中间对齐模式2Center Aligned mode3 中间对齐模式3Counter Period 计数周期Internal Clock Division (CKD) 内部时钟分割No Division 内部时钟不分频Division by 2 时钟除以2Division by 4 时钟除以4Repetition Counter 重复计数Slave Mode Controller 从模式控制器 Slave mode disable 关闭从模式Trigger Output(TRGO) Parameters 触发输出参数设置Master/Slave Mode 主从模式Disable(no sync between this TIM(Master)and its slaves)Enable(sync between this TIM(Master)and its slaves)Trigger Event Selection 触发事件选择Reset(UG bit from TIMx_EGR)复位Enable(CNT_EN) 使能从定时器Update Event 更新事件Compare Pulse(OC1) 比较脉冲Output Compare(OC1REF) 输出比较1Output Compare (OC2REF) 输出比较2Output Compare (OC3REF) 输出比较3Output Compare (OC4REF) 输出比较4Break and dead time management 刹车死区时间管理BRK State 刹车状态Disable 关闭Enable 打开BRK Polarity 刹车极性High 高电平Low 低电平Automatic Output State 自动输出状态Disabled 关闭Enabled 打开Off State Selection for Run Mode (OSSR) Disabled 关闭Enabled 打开Off State Selection for Idle Mode (OSSI) Disabled 关闭Enabled 打开Lock Configuration 定时器锁定配置Off 关闭Lock Level 1 锁定1Lock Level 2 锁定2Lock Level 3 锁定3Output compare no output channel 2 输出比较输出通道2NMode 模式Frozen(used for Timing base) 冻结Active Level on match 匹配输出高电平Inactive Level on match 匹配输出低电平Toggle Level on match 匹配翻转电平Forced Active 强制输出高电平Forced Inactive 强制输出低电平Pulse (16 bits value) 脉冲宽度（16位）CH Polarity 输出通道极性High 高Low 低CH Idle State 输出通道闲置状态Set 置高Reset 复位低Output compare channel 3 输出比较通道3Mode 模式Frozen(used for Timing base) 冻结Active Level on match 匹配输出高电平 Inactive Level on match 匹配输出低电平Toggle on match 匹配翻转电平Forced Active 强制输出高电平Forced Inactive 强制输出低电平Pulse (16 bits value) 脉冲宽度（16位）CH Polarity输出通道极性High 高Low 低CH Idle State输出通道闲置状态Set 置高Reset 复位低USART1 Configuration 串口1 配置Baud Rate 波特率Word Length 数据长度8bits（including parity） 8位（包含校验位）9bits（including parity）9位（包含校验位）Parity 检验位None 没有校验Even 偶校验Odd 奇校验Stop Bits 停止位1 1个停止位2 2个停止位Advanced Parameters 高级参数设置Data Direction 数据传输方向Receive and Transmit 接收和发送Receive Only 仅接收Transmit Only 仅发送Over Sampling 过采样16 Samples 采样16次8 Samples 采样8次Single Sample Disable 关闭Enable 打开Advanced Features 高级特性Auto Baudrate 自动波特率Disabled 关闭Enabled 打开TX Pin Active Level Is Inverted Disabled 关闭Enabled 打开RX Pin Active Level Is Inverted Disabled 关闭Enabled 打开Data Are Inverted Disabled 关闭Enabled 打开TX and RX Pins Are Swapped 发送和接收引脚交换Disabled 关闭Enabled 打开Overrun Disable 关闭数据覆盖Disabled 关闭Enabled 打开DMA Disable on RX Error RX脚错误关闭DMADisabled 关闭Enabled 打开MSB Is Sent First 最高位先发送Disabled 关闭Enabled 打开SPI1 Configuration SPI1 配置Frame Format 帧格式 MotorolaData Size 传输数据大小4 Bits 4位5 Bits 5位6 Bits 6位7 Bits 7位8 Bits 8位9 Bits 9位10 Bits 10位11 Bits 11位Clock Parameters（时钟参数 ）Prescaler (for Baud Rate) 分频（针对波特率）2 2分频4 4分频8 8分频16 16分频Baud Rate 波特率Clock Polarity (CPOL) 数据采样时时钟极性Low 低High 高Clock Phase (CPHA)数据采样时时钟相位1 Edge 第一个边沿2 Edge 第二个边沿Advanced Parameters 高级参数设置CRC Calculation CRC 计算Disabled 关闭Enabled 打开I2C1 Configuration I2C1 配置I2C Speed Mode Standard Mode 标准模式Fast Mode 快速模式Fast Mode Plus 快速模式+I2C Speed Frequency (KHz) I2C速度Rise Time (ns) 上升时间 Fall Time (ns) 下降时间Coefficient of Digital Filter Analog Filter 模拟滤波器Disabled 关闭Enabled 打开Slave features 从模式特性Clock No Stretch Mode时钟没有扩展模式 Clock Stretch Disabled 关闭时钟扩展Clock Stretch Enabled 打开时钟扩展General Call Address Detection通用呼叫检测Disabled 关闭Enabled 打开Primary Address Length selection原始地址长度检测7-bit 7位10-bit 10位Primary slave address 原始从地址Dual Address Acknowledged双地址确认Disabled 关闭Enabled 打开IWDG Configuration 独立看门狗设置IWDG counter clock prescaler独立看门狗计数时钟分频器 48163264128256I