CP6 IO中英文对照表.xls

CP6 I O 內容介紹 INPUT 1 MX100INPUT 2 MX100 LED NO 原文中文注解LED NO 原文 A00X000 EMERGENCY SW緊急開關A00X020MACHINE READY A01X001 START SW啟動開關A01X021AIR OK A02X002 RESET SW恢复狀態A02X022THERMAL OK A03X003 CYCLE STOP SW暫停開關A03X023SERVO READY A08X008 INCHING RIGHT右移A04X024TABLE READY A09X009 INCHING LEFT左移A08X028FRONT DOOR OK A0AX00A INCHING DOWN下移A09X029READY DOOR OK A0BX00B INCHING UP上移A0AX02ALOADER PLC OK A0CX00C INCHING CW順轉A0BX02BVACUUM OK A0DX00D INCHING CCW逆轉A0CX02CCAM HANDLE CHK A0FX00F SHIFT KEY加速A0DX02DFEEDER CHK B00X010 F1功能鍵F1A0EX02EFENCE1 CHECK B01X011 F2功能鍵F2A0FX02FFENCE2 CHK B02X012 F3功能鍵F3B00X030TABLE UPCHK1 B03X013 F4功能鍵F4B01X031TABLE DNCHK1 B04X014 F5功能鍵F5B02X032TABLE DNCHK2 B05X015 F6功能鍵F6B03X033PCB SET OK B06X016B04X034TAPE CUTTER UP B07X017 B05X035TAPE CUTTER DN B08X018 E1功能選擇鍵1B06X036HARD READY B09X019 E2功能選擇鍵2B07X037LARGE PCB B0AX01A E3功能選擇鍵3B08X038CONV PLUS OT B0BX01B E4功能選擇鍵4B09X039CONV MINUS OT B0CX01C TENKEY 1數字組合B0AX03ACONV PCB CHK B0DX01D TENKEY 2數字組合B0BX03BREAR OPERATION B0EX01E TENKEY 4數字組合B0CX03CFEEDING FW POS B0FX01F TENKEY 8數字組合B0DX03DFEEDING BW POS B0EX03ECAM ZERO POS B0FX03FR FENCE MODE INPUT3 MX100INPUT3 MX100 LED NO 原文中文注解LED NO 原文 A00X040 SERVO BOX1第一伺服箱功能正常B00X050 PRQ ROT 270DEG A01X041 SERVO BOX2第二伺服箱功能正常B01X051 PRQ ROT 90DEG A02X042 TAPE END CHK料結束檢查B02X052 NOZ ORG POS ST12 A03X043 L PICKUP CHK第二站偵測B03X053 NOZ CLUT ST12 A04X044 PQ ROT 270DEG預轉270度偵測B04X054 DUMP PARTS A05X045 PQ ROT 90DEG預轉90度偵測B05X055 OIL ALARM A06X046 SET CANCCEL 1右邊驅動桌面設定取消B06X056 NOZ ORG POS ST15 A07X047 SET CANCCEL 2左邊驅動桌面設定取消B07X057CYCLE MODE V3 15 A08X048 MIDDLE DEVICEB08X058 SET COMPLETE1 A09X049 HEAD A CHK A 頭偵測B09X059 SET COMPLETE2 A0AX04A NOZ CHK ST17 117站1號偵測B0AX05A SHUTTER1 UPCHK A0BX04B NOZ CHK ST17 217站2號偵測B0BX05B SHUTTER1 DNCHK A0CX04C NOZ CHK ST17 317站3號偵測B0CX05C SHUTTER2 UPCHK A0DX04D NOZ CHK ST19 119站1號偵測B0DX05D SHUTTER2 DNCHK A0EX04E NOZ CHK ST19 219站2號偵測B0EX05E TRANSFER IN A0FX04F NOZ CHK ST19 319站3號偵測B0FX05F TRANSFER OUT 核准 制表 郭井泉 CP6 I O 內容介紹 OUTPUT 1 MX100OUTPUT 2 MX100 LED NO 原文中文注解LED NO 原文 A00Y000 SATRT LAMP ON開始鍵燈亮A00Y020 PICKUP SOL ON A01Y001 RESET LAMP ON恢复鍵燈亮A01Y021 PICKUP SOL OFF A02Y002 BUZZER ON喇叭響A02Y022 PQ ROT SOL ON A03Y003 TM CNTR ONA03Y023 PQ ROT SOL OFF A04Y004 SERVO HOLDA04Y024 PQ ROT 90DEG A05Y005 TIME COUNT ON時間計數開A05Y025 PQ ROT 270DEG A06Y006 AUTO OPERATION自動操作模式A06Y026TAPE FEED SOL ON A08Y008 TABLE UP桌面上驅動A07Y027TAPE FEED SOL OFF A09Y009 TABLE DOWN桌面下驅動A08Y028 PLACE SOL ON A0AY00A CONV WIDE ON軌道寬開A09Y029 PLACE SOL OFF A0BY00B CONV NARROW軌道窄開A0AY02A NOZ SOL ON A0CY00C D1 SERVO OND1軸伺服准備正常A0BY02B NOZ SOL OFF A0DY00D D2 SERVO OND2軸伺服准備正常A0CY02C PRQ ROT SOL ON A0EY00E SERVO ON伺服正常A0DY02D PRQ ROT SOL OFF B04Y014 SHUTTER1 UP D軸門上下驅動 A0EY02E PRQ ROT 90DEG B05Y015 SHUTTER1 DOWNA0FY02F PRQ ROT 270DEG B06Y016 SHUTTER2 UPB00Y030 FQ SOL ON B07Y017 SHUTTER2 DOWNB01Y031 FQ SOL OFF B0DY01D FOLLOW PERMITB02Y032 F LIGHT OPEN B0EY01E BC LAMP1 ONB03Y033 F LIGHT SHUT B0FY01F BC LAMP2 ONB04Y034 FEED ON B05Y035 S LIGHT OPEN B06Y036 TAPE CUTTER X軸 置件平台 左右驅動軸C軸 凸輪驅動軸NC軸 吸頭切換驅動軸 Y軸 置件平台 前后驅動軸FQ軸 最終置件角度驅動軸D軸 供料平台驅動軸 Z軸 置件平台 升降驅動軸FRQ軸 最終置件角度還原驅動軸PQ 預轉 PRQ 預轉還原 OUTPUT 3 MX100OUTPUT 3 MX100 LED NO 原文中文注解LED NO 原文 A01Y041OTVL CUT ON极限控制檢查B01Y051 A02Y042FIDU LAMP ONMARK 燈亮B02Y052 A03Y043RINGBLOW ONB03Y053 A04Y044D1 SET LIGHTD1軸信號燈亮B04Y054 A05Y045D1 SET FLASHD1軸信號燈閃B05Y055 A06Y046D2 SET LIGHTD2軸信號燈亮B06Y056 A07Y047D2 SET FLASHD2軸信號燈閃B07Y057 A08Y048RED LIGHT紅燈B08Y058 A09Y049YELLOW LIGHT黃燈B09Y059 A0AY04ABLUE LIGHT綠燈B0AY05A A0BY04BRED FIGHT紅燈閃B0BY05B A0CY04CTELLOW FLASH黃燈閃B0CY05C A0DY04DBLUE FLASH綠燈閃B0DY50D A0FY04FKEEP POWER ON電源保護開B0EY05E CP6 I O 內容介紹 BOARD LOADER PLC INPUT 1BOARD LOADER PLC INPUT 2 LED NO 原文中文注解LED NO 原文 A00LX000 LOAER STOP板運輸緊急停止A00LX020 ID DECEL PNT1 A01LX001 PCB AVAIL INA01LX021 ID ARRV CHK1 A02LX002 PCB REQ IN進板信號A02LX022 ID DECEL PNT2 A03LX003 IN REDUCE POS前進板減速A03LX023 ID ARRV CHK2 A04LX004 IN PCB CONF前進板到位确認A04LX024 ID W CONV OT A05LX005 IN STOPPER ON進板檔板開偵測A05LX025 ID W CONV OT A06LX006 IN STOPPER OFF進板檔板關偵測A06LX026 ID INCHING A08LX008 MAIN REDU POS中間進板減速A07LX027 ID INCHING A09LX009 MAIN PCB CONF中間進板到位确認A08LX028 ID FOLLOW CHK A0A LX00A MAIN STOP ON中間檔板開偵測A09LX029 ID FOLLOW CHK A0B LX00B MAIN STOP OFF中間檔板關偵測A0A LX02A ID STRR1 ON A0C LX00C PCB OUT CHECK出板檢查A0B LX02B ID STRR1 OFF A0D LX00D OUT PCB CONF出板确認A0C LX02C ID STRR2 ON B00LX010 WAIT INPUT等待輸入A0D LX02D ID STRR2 OFF B01LX011 MCI D ONA0ELX02E ID PCB TRAN A0FLX02F FOLLOW PERMIT B00LX030 FOLLOW CHK OP LINK INPUT 1BOARD LOADER PLC OUTPUT 1 LED ON 原文中文注解LED ON 原文 A00LX200 LOADER PLC OK 不 譯 A00LY000 PCB REQ OUT A01LX201 LOADER ALARM1A01LY001 PCB AVAIL OUT A02LX202 LOADER ALARM2A02LY002 IN CONVEYOR A03LX203 LOADER CMPLTA03LY003 IN REDUCE A04LX204 CLEAROFF CMPLTA04LY004 IN STOPPER A05LX205 PCB WAITA05LY005 MAIN CONVEYOR A06LX206 NEXT WAITA06LY006 MAIN REDUCE A07LX207 LOADER WORKA07LY007 MAIN STOPPER A08LX208 MAIN PCB CHKA08LY008 OUT CONVEYOR SERVO INPUT 1SERVO INPUT 2 LED NO 原文中文注解LED NO 原文 SX000 NO1EMERGENCY緊急開關SX010 NO2EMERGENCY SX006 C AXIS ZEROCAM軸零點SX014 X AXIS OT SX00AFRQ AXIS ZEROFRQ 軸零點SX015 X AXIS OT SX00CZ AXIS OTZ軸正极限SX016 X AXIS ZERO SX00DZ AXIS OTZ軸負极限SX017X AXIS READY SX00EZ AXIS ZEROZ軸零點SX018Y AXIS OT SX019Y AXIS OT SERVO INPUT 3SX10AY AXIS ZERO LED NO 原文中文注解SX01BY AXIS READY SX010NO3EMERGENCY緊急開關SX01EFQ AXIS ZERO SX024D1 AXIS OTD1軸正极限 SX025D1 AXIS OTD1軸負极限SERVO INPUT 3 SX026D1AXIS ZEROD1軸零點LED NO 原文 SX028D2 AXIS OTD2軸正极限SX02AD2AXIS ZERO SX029D2 AXIS OTD2軸負极限SX02ENC AXIS ZERO 中文注解 机器准備正常 气壓正常 溫度正常 伺服准備正常 桌面准備正常 前門正常 后門正常 運輸控制板正常 真空正常 手搖把柄檢查 料槍水平感應器 D TABLE的門安全 檢查 桌面上偵測 桌面下偵測 loaging position 板定位檢查 5000机型才有 5000机型才有 5000机型才有 調板寬度正极限 調板寬度負极限 桌面板檢查 前后轉換開關 推料槍前的位置 推料槍后的位置 CAM軸零點位置 后柵欄循環停止模式 中文注解