Shigley’s Mechanical Engineering Design, 9th Edition.doc

Shigleys Mechanical Engineering Design, 9th EditionFirst Printing CorrectionsThe authors apologize for any inconvenience caused by errors in the first printing of the ninth edition of Shigleys Mechanical Engineering Design. We had made every attempt to avoid these problems. However, with a text of over 1000 pages and a solutions manual of over 760 pages there were bound to be errors, typographical and otherwise. In this edition, there were over 600 new and revised problems. Many of the errors in Appendix B, Answers to Selected Problems, were due to improper rounding and thus are only off by a small percentage. However small these errors need to be corrected and reported.Richard G. BudynasJ. Keith NisbettShigleys Mechanical Engineering Design, 9th EditionErrata First Printing CorrectionsPage 19. Equation (1-5) should be changed ro read “”.Page 20. Figure 1-4. Change “lengths a, b, and c ” to “lengths b, c, and d ”.Page 27. Second line of Prob. 1-12. Change “16”to “32”.Page 47. Last line. Change “recrystallation” to “recrystallization”.Page 67. Prob. 2-3. First line. Change “strength-to-weight density” to “strength-to-density”.Page 116. Third line before Eq. (3-58). Change first comma to a period.Page 144. In Prob. 3-122 statement and figure. Change R to Ri (3 places total). In Prob. 3-124. Change R to Ri. In Prob. 3-125. Change R to Ri.Page 146. In Prob. 3-142. In third column, change “mm” to “in”.Page 173. In second integral of Eq. (6) change “dx ” to “dq ”.Page 202. In Prob. 4-71. Change “(4-15)” to “(4-18)”.Page 203. In Prob. 4-78. In figure, Section A-A. Change “1.375 in” to “0.375 in” (2 places).Page 241. In third line. Change “Eq. (5-34)” to “Eq. (5-33)”.Page 260. In Prob 5-57. Change “Design” to “Using F = 416 lbf, design”. In Prob. 5-59. Fifth line. Change “1.5 in” to “0.5 in”.Page 263. Prob. 5-87. First line. Change “5-44” to “5-86”. Prob. 5-88. Second line. Change (40,2)” to “(20,1)”.Page 333. In Table 6-11. Top heading. Remove the minus superscript just before the b.Page 355. Prob. 6-70. First line. Change “forces F are” to “force F is”. Second line. Change “reversed” to “reversed at 10.5 kip”. Last line. Change “Fa” to “F ” .Page 400. Prob. 7-2. Second line. Delete the word “metric”.Page 407. Prob. 7-32. First line. Change “The shaft” to “The steel shaft”.Page 446. Last line. Change “Eqs. (6-40), (6-41), and (6-42)” to “Eqs. (6-41), (6-42), and (6-43)”Page 460. Prob. 8-7. Replace the first three lines with “For the screw clamp shown, a force is applied at the end of the handle 3in from the screw centerline. The in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 UNC and is 8 in long, overall. The maximum possible length of screw in the clamping region is 6 in.”In the figure, delete the dimensions for A and B. Add the horizontal dimension of 3in from the left ball on the handle to the centerline of the screw.Page 512. Prob 9-42. Fourth line. Change “bending moment of 100 kip in in” to “10 kip bending load 10 in from”.Page 513. Prob. 9-48. Left figure. The upper arrow of the 5 in vertical dimension should intersect the top of the top plate.Page 564. Prob. 10-28. Third line. Change “music” to “oil tempered”.Page 566. Prob. 10-41(c). Change “Estimate” to “For part (b), estimate”.Page 610. Prob. 11-26. Fourth column. Change “109 rev” to “108 rev”.Page 670. Prob. 12-13. Last line. Change “hp” to “h0”. Prob. 12-15. First line. Change “bearing has” to “bearing with l / d = 1 has”. Fourth line. Change “70F” to “70F with a = 1”.Page 721. Prob. 13-14. Third line. Change “ft” to “f”.Page 761. Heading for Sec. 14-12. Change “CH” to “CH (ZW)”.Page 927. Prob. 17-13. Change “Use Eq. (17-8) to” to “Use Eq. (17-8) with negligible centrifugal force to”. Prob. 17-13. Last line. Change “F1a” to “(F1)a”.Page 929. Prob. 17-34. First line. Change “9000-lbf” to “7000-lbf”. Second line. Change “cage” to “cage which weighs 1000 lbf”. Change “Prob. 4-6” to “Prob. 4-7”.The remaining changes apply to Appendix B, Pages 1059 - 1064.Chapter 2Prob. 2-6. Change first line to read “(b) E = 30.5 Mpsi, Sy = 45.6 kpsi, Sut = 85.6 kpsi, area”.Prob. 2-15. Change “1.28” to “1.27”.Prob. 2-26. Change “aluminum” to “aluminum alloys”.Chapter 3Prob. 3-1. Change “66.6” to “66.7”.Prob. 3-14. Second line. Change “215” to “214”.Prob. 3-27. Change “5.9” to “5.86”.Prob 3-40. Change “(a)” to “Model c:”. Change “(b)” to “model d:”. Change “(c)” to “model e:”.Prob. 3-53(b). Change 0.00348 rad/mm” to “0.348 rad/m”.Prob. 3-69(b). Change “RO = 1794 N” to “RC = 1794 N”. Change “RC = 3036 N” to “RO = 3036 N”.Prob. 3-69(e). Change “s1 = 276 MPa” to “s1 = 275 MPa”.Prob. 3-72. Change “183” to “183.1”. Change “861” to “861.5”. Change “209” to “208.5”. Change “259” to “259.3”.Prob. 3-84. Second line. Change “s2 = - 6.72 kpsi” to “s2 = - 6.7 kpsi”.Prob. 3-104. Change “sl = - 18.6 psi” to “sl = - 254 psi”. Change “t1/3 = 2870 psi” to “t1/3 = 2980 psi”. Change “t1/2 = 2860 psi” to “t1/2 = 2870 psi”. Change “t2/3 = 2.6 psi” to “t2/3 = 115 psi”.Prob. 3-108. Change “tmax = 2.66 kpsi” to “tmax = 2.68 kpsi”.Prob. 3-116. Change “p = 11.5 kpsi” to “p = 8.33 kpsi”. Change “(st )i = - 11.5 kpsi” to “(st )i = - 8.33 kpsi”. Change “(st )o = 30.0 kpsi” to “(st )o = 21.7 kpsi”.Prob. 3-126(c). Change “ki = 1.255, ko “ to “Ki = 1.26, Ko “.Prob. 3-129. Change “si = 182 MPa, so = - 47.8 MPa” to “si = 64.6 MPa, so = - 21.7 MPa”.Prob. 3-133. Change “smax = 353 F1/3 MPa” to “smax = 352 F1/3 MPa”.Prob. 3-138. Change “F = 117 lbf” to “F = 95.3 lbf”.Chapter 4Prob. 4-7. Change entire line to read “d = 5.262 in, % elongation due to weight = 3.21%”.Prob. 4-24. Change “yA = 7.99 mm” to “yA = - 7.99 mm”.Prob. 4-27. The complete solution should read “yA = 0.0805 in, zA = - 0.1169 in, (qA)y = 0.001 15 rad, (qA)z = 8.06 (10-5) rad”.Prob. 4-30. Change “qOz“ to “(qO)z“.Change “qCz“ to “(qC)z“.Prob. 4-33. The complete solution should read “(qO)y = 0.0104 rad, (qO)z = 0.007 51 rad, (qC)y = - 0.0193 rad, (qC)z = - 0.0109 rad”.Prob. 4-39. Change “d = 2.88 in” to “d = 2.68 in”.Prob. 4-41. Change “y = - 0.1041 in” to “y = 0.1041 in”.Prob. 4-43. Second line should read “q = 0.0345 rad, 1.33 times greater, 0.847 in”.Prob. 4-46. Add the following “, ymax = - 0.0678 mm”.Prob. 4-73. Change “20.1% difference” to “1.20 times greater”.Prob. 4-78. Change “d = 0.009 in” to “d = 0.0226 in”.Prob. 4-85. Change “d = 0.618 mm” to “d = 6.067 mm”.Prob. 4-90. Second line. Change “50.6” to “50.7”. Change “- 12.1” to “- 12.0”.Prob. 4-92. Change “22.3 mm” to “0.0223 mm”.Prob. 4-97. Second line. Change “0.0062” to “ 0.006 22”. Change “14.7” to “-14.7”.Prob. 4-101. Third line. Change “- 0.0129” to “- 0.0131”.Chapter 5Prob. 5-12(d). Change “2.03” to “2.04”.Prob. 5-40. Change “1.28” to “1.29”. Change “1.31” to “1.32”.Prob. 5-48. Change “12.5” to “13.9”. Change “10.1” to “14.3”.Prob. 5-53. Change “2.25” to “1.30”. Change “4.55” to “1.40”.Prob. 5-58. Change “1.08 kpsi” to “934 psi”. Change “1.29” to “1.11”.Prob. 5-63. Change “1.12” to “0.892”.Prob. 5-74. Change “2.58” to “1.84”. Change “2.38” to “1.80”.Prob. 5-84(a). Change “1140” to “958”.Prob. 5-86. Change “N(- 31 000, 2899) psi” to “N(- 31.1, 2.899) kpsi”. Change “N(48 760, 3445) psi” to “N(48.76, 3.445) kpsi”.Chapter 6Prob. 6-1. Change “435” to “433”.Prob. 6-15. Change “1.42” to “0.73”.Prob. 6-20(c). Change “1.31” to “1.32”.Prob. 6-25. Change “3.3” to “3.32”.Prob. 6-33. Change “23.1” to “23.0”. Change “28.3” to “28.2”. Change “2.18” to “2.14”.Prob. 6-46. Change “5.45” to “6.06”.Prob. 6-57. Change “5.28” to “5.29”.Prob. 6-66. Change “0.994” to “0.995”.Prob. 6-68. Change “0.824” to “0.999 96”.Chapter 7Prob. 7-2. Second line. Change “0.063” to “0.0625”.Prob. 7-42(d). Change “0.3” to “0.8”. Change “1010” to “2700”.Chapter 8Prob. 8-4. Change “7.827” to “7.83”.Prob. 8-33. Change “1.30” to “1.29”. Change “11.77” to “11.1”. Change “11.58” to “11.8”.Prob. 8-37. Change “1.30” to “1.29”. Change “12.53” to “10.7”. Change “11.36” to “12.0”.Prob. 8-41. Third to fifth lines. Change “926” to “854”. Change “0.202” to “0.215”. Change “1.23” to “1.22”. Change “3.77” to “3.53”. Change “np = 2.86” to “n0 = 2.90”.Prob. 8-51. Change “8.04” to “7.55”. Change “12.1” to “11.4”. Change “10.4” to “9.73”.Prob. 8-55. Change “12.7” to “11.9”.Chapter 9Prob. 9-5. Change “51.0” to “51.2”.Prob. 9-45. Change “25.6” to “25.5”.Chapter 10Prob. 10-5. Change “69.6” to “67.2”. Change “1.78” to “2.04”.Prob. (10-17). Replace all with “Spring is not solid safe (ns 1.2), L0 = 68.2 mm”.Prob. 10-28(d). Change “8.46” to “8.69”.Prob. 10-42. Change “k = EI” to “(a) k = 12 EI”. Change “3.02” to “36.3”. Change “3.24” to “3.25”.Chapter 11Prob. 11-1. Change “24.2” to “2