研华自动化工业数字视讯监控系统简介与FAQs.doc

研华自动化工业数字视讯监控系统简介与FAQs典型的工业视频监控系统框图如下，本系统符合现有大陆国内众多项目之要求。系统描述：如上图所示，DVX-4300型IVS系统由研华一台IPC、PV 系列如PV-600E , PV-800E , PV-1000E, PV-2000E 以及PV-2100E型视频采集卡和PowerView IVS软件组成，进行捕捉视讯讯号，显示现场视频，并完成智慧视频侦测，例如可以完成虚拟栅栏（virtual fence）、不明出现目标侦测、丢失物件跟踪、滞留侦测、跌倒侦测, 人流车流计数侦测功能, 目前提供6个智能视频侦测功能, 但一台IPC仅支持其中的4个功能。DVX-4100型DVR是由IPC平台、PV 系列视频采集卡和PowerView6000软件组成，完成视频记录功能。DVX-4200型CMS由一台IPC安装PowerView CMS组成，完成中央管控功能。DVX-4400型VIS由一台IPC安装PowerView VIS软件组成，完成视频集成功能，充当视频Server，从现场的DVR获取实时视频画面并且向internet网络发布。一般功能之Q&A：DVX-4300型IVS系统部分1， 请问智能视频监控任务的完成，需要哪几部分的配合工作？答：IVS采集到视频画面，预先设置虚拟栅栏侦测功能，一旦有目标侵入该区域，IVS就会侦测到该入侵行为并且产生一个视频事件，IVS本身亦能针对事件做处置；当事件发生时，IVS可以反应动作如 DO输出、快照、声音播放及执行某一应用程序等四项。这些行为在无需与DVR联机的情况下即可完成, 或可将该视频事件描述通过Ethernet网络传送给DVR，DVR收到该视频事件后就会产生相应的预先设定的工作：例如启动录像或拍照，云台启动跟踪，发出报警等等。总结：智能视频监控任务的完成，可以IVS独立运作或将IVS和DVR两个系统的紧密配合完成或。2， 请问IVS和DVR的通信，除了上面提到的通过Ethernet网络，还有别的通信方式吗？答：目前只有通过Ethernet网络进行数据交换。3，IVS侦测到入侵行为并且产生一个视频事件后，能否自己发出DO动作来产生一个报警？答：需要另外增加一块DO板块或者ADAM模块才能完成DO输出，例如PV-2100E型视频采集卡本身没有DO输出功能。4， IVS的虚拟栅栏功能，在同一幅视频画面，可以设置多个区域吗？答：侦测区域和侦测出的物体是不一样的；侦测区域最大的上限是11个，但同时侦测物体可达32个。例如防物品丢失功能，最多也可以设置11个跟踪目标属于侦测之物体，故理论上可同时侦测32个。相同的,人流/车流计数侦测区域最多也可以设置11个；。5， IVS可以根据智慧视频分析的结果，进行PTZ控制吗？答：IVS不能完成PTZ控制。需要DVR的配合来完成该功能。6， IVS和DVR可以共享一个摄像头吗？答：IVS和DVR可以共享一个摄像头，即一个摄像头分出2条线路分别送给IVS和DVR。但是如果DVR要实现PTZ控制时，最好各自用一路摄像头，以免冲突。7，IVS侦测到入侵行为并且产生一个视频事件后，能否进行拍照？答：可以进行拍照，并且存储在本地硬盘。但是不能远程发布照片。8， 如果同时需要完成虚拟栅栏侦测和物品丢失侦测，是否可以共享一个摄像头？答：不能。需要2个摄像头完成对应功能。9，IVS侦测并且产生一个视频事件后，能否自己发出信息送给CMS？答：目前IVS不能与CMS直接联机，IVS需先行与DVR联机后，再由DVR与CMS连接。故事件的传送也是IVS-DVR-CMS。DVX-4100型DVR系统部分10, DVR具备那些IVS所没有的功能？答：视频录像和本地视频备份，云台控制（PTZ），报警，视频网络发布（充当Video Server），字符迭加(iOSD，文本信息显示于视频画面），ADAM 4000/6000集成 , POS , ATM 以及第3方设备集成等.11，DVR的视频画面可以通过3G手机或者PMD(手持终端设备)远程来访问吗？答：可以。但是DVR需要链入internet网络，充当视讯服务器，手机或者PMD(手持终端设备)通过Internet网络访问DVR的IP地址来获取视频画面。12,我们知道研华可以把IO信息通过iOSD的功能显示于频画面，那么当需要显示的IO数据变得很多，甚至是成百上千个IO数据需要显示，怎么办？答：此时我们可以借助于webaccess来实现。IO数据在webaccess上管理和显示，视频画面嵌入在webaccesss上。总结：当IO资料量很多，视频画面不多的情况下，显示模式采用将视频画面嵌入在webaccesss上的方式；反之，需要显示的IO数据量不多的情况下，采用将IO信息通过iOSD的功能显示于频画面上的模式。13，DVR上面运行的PowerView软件所显示的视频画面，可以迭加其它图片或者线条图框吗？答：不可以。目前DVR上面运行的PowerView软件所显示的视频画面，只支持文本标注（即iOSD：Information On Screen Display）。不能迭加其它图片或者线条图框。14，可以在一台IPC上面安装2块PV-2100E视频采集卡，同时运行PowerView6000和PowerView6000 IVS软件，用一台IPC实现完整的智能视频监控功能吗？答：不能。由于运算负荷的原因，出于可靠性考虑，目前需要两个工业计算机平台（IPC或者UNO）来分别运行PowerView6000和PowerView6000 IVS软件，从而实现完整的智能视频监控功能。DVX-4200型CMS系统部分15，图中视频监控中心的CMS系统，最多可以管理多少摄像头？DVX-4200最多支持几重画面显示？答：最多可以同时联机监看最多管理128个摄像头 , 但可管理DVR的数目不限。DVX-4200,最多支持最多可显示3个屏幕, 但需要2张显示卡才能达成3屏幕输出, 分别有64ch及时监看分割画面,16ch远程分割回放,E-MAP,事件过滤显示, 等几种显示方式可让使用者可选择。16，图中视频监控中心的CMS系统，所显示的视频画面，是由DVR主动发送而来，还是CMS系统主动从DVR获取数据？答：CMS主动从不同的DVR获取数据。CMS是客户端（Client），DVR是视讯服务器（Server）。17，CMS可以实现远程视频数据备份（Remote Backup）吗？答：CMS可以实现远程视频实时播放，历史画面回放，可予许使用者针对所选择的DVR摄影机以及选定的时间范围内做远程备份。18，VIS和CMS和区别是什么？答：VIS是视频集成系统，充当视讯服务器，它把各个DVR视频数据整合在一起，并且通过网络发布给各个客户端，例如PMD，与具有MS Mobile OS的3G手机支持与VIS的整合测试 , 可以远程通过IE来访问VIS来获取现场的视频画面。CMS是中央监控系统，完成中心视频管控功能，它是客户端，网络的其它客户端无法访问CMS主机里面数据。18，CMS可以通过访问VIS来访问现场DVR的视频资料吗？答：CMS不须通过访问VIS来访问现场DVR的视频数据，CMS可以直接访问现场的DVR来获取需要的视频画面。19，PowerView6000 ，PowerView6000 IVS，PowerView CMS，PowerView VIS软件，是否都必需和研华自动化的视频采集卡硬件配合才能运行？答：PowerView6000 和PowerView6000 IVS不能单独运行，必须和研华自动化的视频采集卡硬件配合才能运行，从而完成正常的功能。PowerView CMS，PowerView VIS软件直接运行于PC机上，不需要视频采集卡硬件的配合20，PowerView6000 ，PowerView6000 IVS，PowerView CMS，PowerView VIS软件，是否都必需和研华自动化的视频采集卡硬件配合才能运行？答：PowerView6000 和PowerView6000 IVS不能单独运行，必须和研华自动化的视频采集卡硬件配合才能运行，从而完成正常的功能。PowerView CMS，PowerView VIS软件直接运行于PC机上，不需要视频采集卡硬件的配合21，CMS，VIS，IVS，PTZ名词缩写，分别是什么意思？答：CMS: Central Monitoring System中央监控系统VIS：Video Integration System视频集成系统IVS：Intelligent Video System智能视频系统DVR: Digital Video Recorder数字视讯录像机PTZ: 英文译义是P-Pan(水平转动)+T-Tilt(垂直转动)+Z-Zoom(景深伸缩), PTZ摄像机是由一个可三维转动的机械云台和一个可伸缩的镜头等构成。PTZ控制就是指的通过软件实现对云台机械装置的控制。22，哪些软件收费？哪些软件免费？答：PowerView 6000：和DVR或者数据采集卡配套所用，免费提供 , 也提供CMSLite可免费使用, 但CMSLite只支持同时联机32支摄影机, 并只有双屏幕输出, 及第一个屏幕是实时远程监看或切换远程回放, 第二个屏幕是E-MapPowerView CMS：安装于独立的IPC，销售价格见价格表。CMSLite可免费使用PowerView IVS：和视频采集卡配套使用，销售价格见价格表。PowerView VIS：安装于独立的IPC，销售价格见价格表。23， 视讯卡对于硬件平台系统最低要求各是多少？客户选型遵循原则是什么？Video CardPV-600, PV-800 , PV-1000 Software CompressionPV-2000, PV-2100 Hardware CompressionCPUIntel P4 2.8 GHz or aboveIntel P4 2.8GHz or aboveMainboardIntel 845, 865 or 915 or above chipset Recommanded Mainboard : AIMB-764G2-00A1EAIMB-562AIMB-763Intel 845, 865 or 915 or above chipsetRecommanded Mainboard : AIMB-764G2-00A1EAIMB-562AIMB-763 VGA CardGeforce FX-5200 128MB or Radeon 9200 128MB or aboveATI 9200 128MB or equal (Support DirectX 9)(Support DirectX 9)RAM1024MB or above1024MB or aboveLAN Ethernet 10/100/1000 MHz DirectXDirectX 9（Provided in Powerview CD）HarddiskRecommanded Harddisk capacity : Base on 1.around 7KB per frame ,2. 4 cameras , record 4 frames per second3. 24 hours recording Total HD Capacity : 9.3GB per day。Recommanded min. 80GB harddisk for long time recording and motion detection recording 。OSWindows XP、Windows2000、Window XP Embedded, Windows 2003 serverPower SupplyRecommanded Power consuption :One Harddisk : 250W2-3 Harddisks :300W3-4 Harddisks :350W4-5 Harddisks :400W5-6Harddisks :460W24， 视频和研华数据采集哪些产品可以整合后一起传输？答：可以和ADAM系列模块和其它IO模块整合25， 研华视频支持哪些格式？答：视频输入支持模拟量NTSC/PAL制式，视频输出支持MPEG1/2/4和H.264压缩格式。26， 摄像头种类？答：摄像头种类为：BNC接头的NTSC/PAL复合视频输出，30/25 fps27， 视频是否支持IP摄像头？答：数据采集卡接入的信号均为BNC接头的NTSC/PAL复合视频输入，因此IP摄像头不能接入到DVR和IVS系统。须等到NVR产品约3Q 2009出来后, CMS或VIS才可与NVR整合。Advantech Automation Industrial Digital Video Surveillance System: Introduction & FAQsThe following is the layout of the typical industrial video surveillance system, which meets with demands on most projects in China. System Description: As shown above, DVX-4300 IVS system consists of an Advantech IPC platform, a PV series of video capture card, such as PV-600E, PV-800E, PV-1000E, PV-2000E and PV-2100E, as well as PowerView IVS software. It is used to capture video signals, display live video, and complete intelligent video surveillance, such as virtual fence detection, unknown objects detection, object loss detection, object persistence detection, object dropping detection and passenger/vehicle counting detection. Now six categories of intelligent video surveillance functions are provided, but one IPC can only support four of them. DVX-4100 DVR consists of IPC platform, PV series of video capture card and PowerView6000 software, supporting video record function. DVX-4200 CMS is served by an IPC installed with PowerView CMS software, supporting central control function. DVX-4400 VIS is served by an IPC installed with PowerView VIS software, supporting video capture function. Used as a video server, DVX-4400 VIS captures live video screen from the on-spot DVR and broadcast it to the internet. Q&A about General Functions:DVX-4300 IVS System3， Q: What cooperated work is needed to complete the intelligent video surveillance task?A: IVS captures the video screen and previously initiate the virtual fence detection function. Once an object invades, IVS will detect it and trigger a video event. IVS can also deal with this event by itself. When an event happens, IVS can react in the way of DO output, snapshot, audio broadcast and executing some application among others. These actions can be finished without DVR connection. IVS can also send the video event description to DVR through Ethernet, and when receiving it, DVR will execute the previous setup work accordingly, such as starting recording or photographing, pan starting and tracking, and alarming. Conclusion: To complete the intelligent video surveillance task, IVS can run independently, or cooperate closely with DVR system. 4， Q: Apart from Ethernet, is there any other communication way for IVS and DVR?A: At present the data transfer can only be conducted through Ethernet.3， Q: After detecting an invasion action and triggering a video event, can IVS send a DO action and alarm by itself? A: Another DO block or ADAM module is needed to complete DO output. For example, PV-2100E video capture card itself doesnt have DO output function. 7， Q: As to IVS virtual fence function, can more zones be set within one video screen? A: The detect zones are not the same as the detected object. The detect zones are limited within 11, but the detected objects can reach 32 at one time. For example, “For object loss precaution function, 11 tracking targets can also be set at the most”, theoretically 32 objects can be detected at the same time. Likewise, the passenger/vehicle counting detection zones can also be set to 11 at the most. 8， Q: Can IVS conduct PTZ control according to the intelligent video analysis result? A: IVS cant conduct PTZ control itself. The cooperation with DVR is demanded. 9， Q: Can IVS and DVR share one camera? A: IVS and DVR can share one camera, that is, one camera can split up 2 lines for IVS and DVR. However, if DVR has to realize the PTZ control function, it is better to use separate cameras to prevent conflict. 7，Q: After detecting an invasion action and triggering a video event, can IVS photograph? A: Yes, but the photos can only be saved at local disks, and are unable to be sent remotely. 9， Q: If it is need to complete the virtual fence detection and object loss detection at the same time, can one camera be shared? A: No, two cameras are needed to complete the relative functions. 9，Q: After detecting an invasion action and triggering a video event, can IVS send a message to CMS by itself? A: At present IVS cant directly connect with CMS, but use DVR as a mediator. So the event is transferred like this: IVS-DVR-CMS.DVX-4100 DVR System10, Q: What other functions does DVR have except those of IVS?A: Video record and local video backup, PTZ, alarming, video web broadcast (as Video Server), character addition (iOSD, text displays over video screen), ADAM 4000/6000 integration, POS, ATM, a third device integration11，Q: Can DVRs video screen be remotely visited through 3G cell phone or PMD (Hand-hold Terminal)?A: Yes. But DVR has to connect with internet as a video server, and cell phone or PMD (hand-hold device) visits DVRs IP address through internet and then captures the video screen. 12, Q: We know that Advantech is able to display IO information on video screen through iOSD function, but if more, even thousands of IO data are in queue, what should we do? A: We can resort to webaccess. IO data can be managed and display on webaccess and video screen is embedded on webaccesss too.Conclusion: When IO information is too much but video images are not, the video screen is embedded on webaccesss; otherwise, when the IO information is not too much, IO information displays on video screen through iOSD function. 13，Q: Can the video image displayed by PowerView software running by DVR overlap with other images, lines or frames?A: No. At present, the video image displayed by PowerView software running by DVR only supports text labeling (or iOSD: Information On Screen Display), but cant overlap with other images, lines or frames. 14，Q: Can we install 2 PV-2100E video capture cards on one IPC, running PowerView6000 and PowerView6000 IVS software meanwhile, and realize the complete intelligent video surveillance function by one IPC? A: No. Due to the computing load, in view of the reliability, now two industrial computing platforms (IPC or UNO) are needed to run PowerView6000 and PowerView6000 IVS software meanwhile, and realize the complete intelligent video surveillance function.DVX-4200 CMS System15，Q: How many cameras can the video surveillance centers CMS system manage at the most? How many tiles of screens can the DVX-4200 display? A: It can manage 128 cameras at the most, but the total number of DVR managed is not limited. DVX-4200 can support 3 screens at the most, which can be achieved through 2 video cards. Users can select 64ch timely monitoring split screen, 16ch remote split playback, E-MAP, event filtering display and other display modes. 16，Q: As to the video images displayed by the video surveillance centers CMS system, are they sent actively by DVR, or actively acquired from DVR by CMS system? A: CMS actively acquires data from different DVR. CMS is Client, while DVR is Video Server. 17，Q: Can CMS realize remote backup of video data? A: CMS can realize remote video live broadcast and screen history playback, and allow for remote backup for selected DVR cameras and schedules. 18，Q: Whats the difference between VIS and CMS?A: VIS (Video Integration System), used as video server, integrates the video data of all DVR and send them to all clients, such as PMD and 3G cell phone with MS Mobile OS through network. They support VIS integrated tests, and can remotely visit VIS through IE and capture the live video screen. CMS (Central Monitoring System) is a client and complete central video monitoring. Other clients of the network cant reach CMS internal data. 18，Q: Can CMS reach the live DVR video information through VIS? A: CMS doesnt need to visit the live DVR video data through VIS. It can directly visit the live DVR and capture the needed video screen. 19，Q: Do PowerView6000, PowerView6000 IVS, PowerView CMS and PowerView VIS software have to work with Advantech Automations video capture card? A: PowerView6000 and PowerView6000 IVS couldnt work separately, but have to cooperate with Advantech Automations video capture card to function normally. PowerView CMS and PowerView VIS software can work within PC directly, without the cooperation with the video capture card. 20，What do CMS,VIS, IVS, PTZ stand for and mean?A:CMS: Central Monitoring System VIS：Video Integration System IVS：Intelligent Video System DVR: Digital Video Recorder PTZ: P-Pan (Horizontal move) + T-Tilt (Vertical Move) + Z-Zoom (Zoom Tele/Wide). PTZ camera is composed of a tri-dimensionally movable mechanical pan and a zoom lens. PTZ Control refers to control on mechanical pan by software. 21，Q: Which software charge? Which are free? A: PowerView 6000: used with DVR or data acquisition card, free, optional free CMSLite, but CMSLite only supports 32 cameras in connection at one time, and only dual screen output. The first screen is for live remote monitoring or remote playback shifting, and the other is E-Map.PowerView CMS: installed on separate IPC (see price list for the sales price). CMSLite is free. PowerView IVS: used with video capture card (see price list for the sales price).PowerView VIS: installed on separate IPC (see price list for the sales price).22, Q: Whats video cards lowest standard for hardware platform system? What do users follow when selecting a product? Video CardPV-600, PV-800 , PV-1000 Software CompressionPV-2000, PV-2100 Hardware CompressionCPUIntel P4 2.8 GHz or aboveIntel P4