SS-67A快速固化的高强度粘接剂硅胶.doc

SS-67A快速固化的高强度粘接剂(如果对本硅胶感兴趣，请与本文分享者联系)High Strength Fast Cure Adhesive Sealant产品描述Product DescriptionSS-67A是一种单组分、高强度、快速室温硫化的脱乙酸机理硅橡胶。它适用于快速实现粘接并达到物理性能指标的要求。固化后的弹性体可抵御气候、臭氧、潮湿、紫外线及高温。SS-67A适用于手工操作及自动设备。SS-67A is a fast curing, high strength, 1-part acetoxy silicone RTV adhesive rubber product engineered for applications requiring fast development of physical properties and excellent adhesion. When cured, the elastomer resists weathering, ozone, moisture, UV and high temperatures. SS-67A works well in manual and automatic dispensing equipment. 产品特点Product Features快速室温硫化 Fast R.T. cure触变型膏剂Thixotropic paste 对塑料、金属和玻璃无需打底层就有极好的结合力Excellent unprimed adhesion to plastic, metal and glass 使用方便，加热可迅速固化Convenient, heat accelerated instant cure capability典型应用Typical Applications流水线粘接 Assembly line adhesive 点胶工艺Form in place gaskets 粘接封闭剂 Adhesive Sealant关于固化Heat Accelerated Curing 通常在开放空间中施用后露置于环境湿度下固化即可形成高强度的橡胶。然而。热风可以大幅提高固化速度并立即实现粘接效果。一分钟热风吹送后再经一分钟湿度条件下冷却，即可固化并形成优异的粘接性能。Typical utilization involves dispensing in open air and ambient humidity to result in a high strength adhesive rubber. However, cure speed can be accelerated with hot air to nearly instant cures exhibiting very fast adhesion. A one minute hot air stream exposure, followed by a one minute cool down in a humid environment, results in cured elastomer exhibiting outstanding adhesion.性能参数Typical Properties固化前：颜色： 半透明黏度（厘泊）： 500,000比重： 1.12粘稠性： 触变型膏剂生效时间（分，室温）： 4表干时间（分，室温）： 12挤出速率（0.62MPa下，克/分）： 250（挤出孔径3mm）UNCURED Color TranslucentViscosity, cps 500,000Specific Gravity 1.12Consistency: thixotropic pasteWorking time, mins 4Tack Free Time, mins. 12Application Rate,90 PSI, g/min. 3mm orifice 0.6 MPa 250固化后（室温）：最高操作温度： 250拉伸强度： 1000PSI/6.89MPa拉伸量： 850%硬度（邵氏A）： 38剥离强度： 50PPI/8.8KN/M剪切强度： 100PPI/17.6 KN/M层面强度： 300PSI/2.27MPa绝缘强度： 19.7KV/mm（500V/mil）介电常数： 2.8耗散因数： 0.001体积电阻率： 2.0 X 1014导热系数： 0.0005热膨胀系数： 20 x 10-5CURED - R.T. Max. Operating Temp. 250 CTensile Strength, PSI 1000 Elongation, % 850 Durometer, Shore A 38 Peel Strength, PPI 50 Tear Strength, PPI 100 Lap Shear Strength, PSI 330 Dielectric Strength, V/mil 500 Dielectric Constant 2.8 Dissipation Factor 0.001Volume Resistivity 2.0 X 1014 Thermal conductivity 0.0005Coefficient of Thermal Expansion 20x10-5使用方法Method of Application 涂覆于工件或装配件的表面，注意不要将所有膏剂都挤出接触面。待充分固化后使用。Dispense sealant onto part and mate parts. Do not squeeze all of the product out of flange assembly. Allow to cure.固体成分Solids98%，不含溶剂成分 98% solids, contains no solvents附着力Adhesion对大多数塑料、金属和常见基底不需要打底层就有很好的结合力Primerless adhesion to most plastics, metals and typical substrates.固化原理Chemical cure system脱乙酸固化Acetoxy cure system使用限制 Limitations不可使用于汽缸盖垫片、燃油或溶剂浸泡的条件下。待完全固化后再使用工件。确保施用空间内有足够剂量以达到效果。Do not use product on head gaskets, fuel or solvent immersion applications. Allow sealant to fully cure before putting assembly into service. Ensure enough product remains between flanges to be effective in an assembly.包装规格Packaging SS-67A可采用292克（10.3盎司）筒装或18.14千克（40磅）桶装或181.4千克（400磅）大桶装。此产品也可根据客户需求，采用其他包装规格。SS-67A is available in 10.3 oz. cartridges, 40 lb. pails and 400 lb. drums. This product is also available in customer defined packaging sizes, upon request.操作及安全Handling and safety 暂不使用时将容器密封以延长保存期。避免孩童接触。未固化的封闭剂对眼睛和皮肤有刺激作用。参考安全技术说明书（MSDS）。For maximum shelf life, keep containers sealed when not in use. Keep out of the reach of children. Uncured sealant irritates eyes and skin. Refer to MSDS.保质期Shelf-life自发货日起，厂家承诺密封条件下1年的保质期。 请在低于22（70F）且干燥环境下贮存。Sealed containers are guaranteed for 1 year from the ship date when stored in a cool dry area below 70 F. 有限承诺Limited warranty 此处提供的表述、技术数据及推荐意见信息是根据我们的测定如实提供的，并相信是准确且可靠的。但由于使用本公司产品的条件和方法非我们所能控制，因此本信息不能取代客户进行的操作，以承诺产品是安全、有效、并完全满足于特定的最终用途。用户应根据自身情况及试验来判断产品是否达到使用效果，并自行承担产品的使用责任及风险。我们所提供的使用建议，不得被视为侵犯任何专利的误导。我们的唯一保证，是产品在发货时满足的销售规格及剂量。如果该保证不能兑现，您所能获得的补偿仅限于退还被保证产品的购货价款或重新更换。特别声明，对于其它特别用途或商品的任何明示或暗示的适用性不作任何保证。我们对买家或第三方的任何事故或由此引起的损失不负任何责任。我们对在本文中未作出陈述的其他书面说法也不作承诺保障。All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as warranty, either expressed or applied. User shall rely on his own information and tests to determine suitability of the product for the intended use, and the user assumes all risk and liability resulting from the use of this product. Manufacturers sole responsibility shall be to replace that portion of product of the manufacturer proves to be defective. Manufacturer shall not be liable to the buyer or any third party for injury, loss or damage directly or indirectly resulting from the use of, or inability to use, the product. Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding by the manufacturer.该产品并未经过黏膜组织、破损皮肤、血液、或植入人体内等领域的测试，也不推荐使用于以上领域。This product has not been tested for,