毛衫QA流程.doc

毛衫QA流程一. 打毛.1. 到打毛车间后,QA要检查打毛车间及打毛机是否整齐,清洁,每个毛筒有否标明缸号纸及不同缸之毛有否混错,打毛驳结是否有正确,同时注意深色,浅色之毛料不可以同是隔离机位打毛,并留意有无飞毛之现象.2. QA在检查打毛过程中,若发现毛料有乱毛,黏缸毛,花毛,粗幼毛,线仔毛或是毛料受潮,霉变,强度不足,拉力欠佳,毛料难打等问题的要立即通知停打停织此毛料,并应立即通知部门主管及公司负责人,同时带此毛料之样本及相关报告数据以便处理.3. 由于毛料条子有粗幼,QA应监督检查开机织大货时,要同时开数机试织其它缸号或颜色,以便能够及时知道重量,颜色上存在的问题,及早做好质量控制工作;若是几条毛混毛一齐织的,QA要检查是否混得均匀,确保混毛均匀才可开织大货.二 织机1. QA要了解清楚自已所要检查的该批货是否已经覆办OK如果没有覆办便开织大货的，要了解清楚原因，同时在查货报告中需注明此点及原因2. 了解该批货的各种生产配料如橡根，膊带等是否已经跟齐如有未齐之现象应立即通知生产部门3.QA要亲自到织机车间抽查织出的衫片,检查字码是否均匀,是否有走字码,字码起横及扯旗之现象并核对织法,开针,加针,排针,收针,转数,剩针等是否正确按照下数纸生产,检查是否有色差等毛料问题.4. 要留意脚高,袖咀高之下数及尺寸是否照足要求.5. 有花款的衫片,如 拨花,挑孔,搬揽,扭绳,间色等款式还要仔细检查有无错毛,挑错孔,搬错针,扭错绳及间错色的现象.6. QA要特别检查若有坑条或扭绳之边位的衫片,不得让工场擅自加减针或作任何更改,一定要照本公司的指示织法,同时留意若是12针驳毛结头要拉边位,不能织到衫片中间,夹边,花位及针数小都不能挂重蛇,以免松针及起蛇,凡是转款或转颜色要检查否清洁每台机台.7. QA要检查下槛的字码,针数,转数是否准确,领贴之开针是开斜角或是包针一定要按下数纸,若领贴是要分开两条织的,字码同转数一定要相同.如发现有错,要实时厂方改善.留意下栏之尺寸及阔度是否符合要求.8. 织机适用检货标准AQL10.0 三. 查补1. QA要到查补车间检查已查补好的衫片及察看补衣工人的技术是否熟练与正确,有否补衣欠佳之现象.检查数量看货量而定,一般按照颜色,缸号,码数等,每打衫(分前后幅及袖)抽查5至6幅即可,不必整打抽查.2. QA在检查衫片时,若发现有漏针,崩边,扯旗,花针,较剪,口单纱,污渍,绣迹及油针,爆孔,散口,收错花,机头不到边,飞毛等疵点问题的,要即刻通知厂方改善好.且每打衫疵点问题不能超过15%以上,否则QA将不会接受而要求重新返工.3. 在检查织片过程中,QA若发现有花毛,粗幼毛,死棉,线仔毛,缸差,易爆孔,断毛,衫片超重或偏轻等现象的,应立刻通知部门主管或公司负责人,同时亦要填写于质量检定报告表内并附上数据分析,说明其重要性.4. 查补好之衫片,要检查有否绑上本公司供给的条形码,有否按批号缸号颜色缸号码数工号件数作好分类.四. 缝盘1. QA到缝盘车间检查缝盘时,一定要对准本公司的缝挑规格表,检查缝法是否正确,尺寸是否准确,缝线松紧要适当,若太松会起耳仔,太紧则会没有弹力,会埋堆等.(如果做需要件染的衫,注意检查缝毛不能用错,还需留意布片,烟纸等要用不上色配料;如果是缝羊仔毛或兔毛的毛衫,还需要用纯羊毛做缝毛,而原身毛料不能作为缝毛,因为很易断.)2. 锁眼不能漏眼,刮边要直,不能有黐边之现象,上袖,埋夹要对花位,夹底不能疏孔.3. 缝元领一定要分清直位,中间及斜位,领形要圆及顺,后领斜位不能缝有直位,缝线不能起蛇,斜位要斜得均匀,不能埋缩在一位置斜.4. 缝杏领时,上领要度尺划位上缝盘,缝起领咀要尖直,两边分位要相称.5. 缝开胸V领衫时要检查两边分位是否相同,缝胸贴要直及尽位,埋夹,上袖不能拉手落盘.以免导致飞机袖及衫身起蛇等.6. 缝间色衫要每一格度一个位.缝线要比一般缝凈色衫拉紧些,以免将不同颜色的缝线露面.7. 如下槛是元筒包缝的,子口不可包得太多,领内杂线要一定清凈.8. 缝打花珠地之毛衫,要检查左右幅是否相称,不能缝正花位及大珠,以防起孔等.9. 如发现有跳,线缸差,漏眼,手势不平均,单纱,断毛,夹底有孔,大细膊,高低,爆缝线,爆夹等情形的,QA要马上通知厂方改善.10. 缝盘适用标准为AQL6.5.五. 裁钑1. QA要检查裁后尺码是否与尺码表相称,注意领形,夹位,袖位及膊位是否完美.2. 钑骨时是否跟裁口,直位要直,弯位要圆滑,否则影响缝盘.3. 检查钑骨时有否把衫片用力拉着钑骨而导致骨口长度加长,缝合后钑骨子口起蛇之现象.4. 检查钑骨缝线松紧度要适中且钑骨线要配色.注意线步不能太疏,否则裁口会散开,但亦不能太密否则会出现蛇形现象.5. 如果某些款式无需再经缝盘,QA须检查在上袖后要在线尾倒钑少许,防止埋夹时把线尾钑断而做成很容易在夹底位置烂开.6. 如果发现有用错钑骨线,钑骨缝线松,断钑骨线,钑骨线露面,钑骨起蛇,钑骨散口,钑骨起狗牙等现象的,QA一定要通知厂方改善好.六 拆纱,挑撞1. QA要严格检查车间挑撞是否用正确之缝毛,是否按照下数或复办指示去做.2. QA要注意检查拆纱时不可把毛尾拉至抽筋,拆纱后必须要拉(猛)眼,线头要收好,所有杂纱一定要执清.3. 挑撞V领咀要拉正中,且要尖直,两边要对称,挑撞线不可过松或过紧.4. 叉位,袋贴顶两边.卷边领后领两边骨卷边位置都须要加针.5. QA要检查若是拨花及挂毛之打结,不能太多毛一齐打,且打结头要实.6. QA要留意检查领口,领咀,袋贴口及胸贴等是否挑撞妥当,注意袖咀,脚底,袋口,夹底及膊位等处线头有没收妥好.七 前整收发1. QA要到收发部检查外机是否按照本公司的生产单,毛料单及发织单内之比例进行生产,不得随意增多或减少其中任何一个色码(否则就会导致后整工场的大量改码而影响到烫衣及装箱的麻烦等问题),一定要外机按照比例均色均码生产.2. QA同时亦要认真核实每打衫之重量,检查工场是否在每打衫上都写有各个色码之正确重量,若发现重量相差太远,有超重或过轻等情况或需要补毛时,就立即通知本公司负责人,以便能够及时改进.八. 前整外发包装1. 每打衫中的色码数一定要相同,不能混错有其它的色码,例如:一打白色M码衫或衫片中,就不能混落有S码或L码之衫或衫片.2. 同时注意不能有落错烟纸之现象,比如:一打S码衫中不能落有M码或L码的烟纸.若发现有此类问题,QA将会不接受而要求厂方返工.3. 检查外机是否在每打衫上都绑有本厂所印发的牌仔或条形码,并且要在牌仔或条形码上数据清楚.4. 检查外机是否把每件衫都整齐折好,并视乎粗幼针,每六件或是十二件一扎,用白色绳仔或白色尼龙绳(近十字结)捆好,装入本公司供给的保洁胶袋.一切正确以后才可交货.成品(后整)质量控制及查货标准一. 此标准作为本厂QC查货标准,适用于后整及所有工序.严重的质量问题称”大鸡”或”不接受”;不明显或是较轻微的疵点称”细鸡”或”小疵点.同一种轻微疵点数超过四个将被视为一个严重疵点,即四件小鸡相等到于一件大鸡.二. 若一件衫中存在有两个或以上严重疵点问题的,则可作为一次严重次品计算;但无论轻微或严重疵点,若在查货中连续不断地出现或疵点问题超过数量之15%(百件计)以上的,QC 将不会接受此批货.1. 用毛:凡不按照吓数或指示用毛条数织衫或缝盘的,都不接受.2. 毛质:花毛,变色属大鸡;粗鴢毛,死棉(毛粒),褪色,受潮,线仔毛,杂质,飞毛等较为严重属大鸡,不接受,.轻微则为细鸡.3. 毛头:在衫面,较明显且超过1/2寸或以上的属大鸡,不明显或在1/2寸以下的则为细鸡.4. 断毛:断毛超过1/2寸或以上的为大鸡.5. 松紧珠:一般情况下属细鸡,严重者为大鸡.6. 走字码:走字码明显不接受,属大鸡.7. 扯旗:衫片左右两边相差超过1/2寸以上属大鸡,不接受.8. 绣花:绣错毛,用错绣花毛不接受,断绣花线或绣花纸托,绣花线头未清好的,严重为大鸡,轻微属细鸡.9. 单纱,漏针,珠路不均,纱口脱散:严重属大鸡.10.针路: 不接受,属大鸡.11. 单毛: 单毛不超过1/2以上的属大鸡,1/2以下的属细鸡.12. 松针:严重则不接受,一般情况属细鸡.13. 烂边,含边,爆孔,跳花,打花不起花,不起珠:不接受,属大鸡.14. 扭绳爆绳,扭绳漏针:属大鸡.15. 字码疏(结):1分或以上属大鸡,一分以下属细鸡(但要从经验对其款式而判断是否接受.16. 开错针,排错针,错扭绳,错转数,错间色,收错花,错领位:属大鸡,不接受.17. 爆孔,漏扭绳,挑错孔,搬错针,机头不到边,油针等属大鸡,不接受.18.抽筋:超过一寸以上属大鸡,一寸以下属细鸡.19.字码不均匀,字码起横:严重属大鸡,不明显属细鸡.20.错花款:不接受,大鸡.21. 橡根,膊带不配色:不接受.22.袖与衫身,领同衫身,前后幅(前后袖不同缸):不接受,属大鸡.23. 打钮不平均,爆钮门:属大鸡,不接受.24. 稀密路:不接受,属大鸡.25. 清洁:锈迹,油渍,枪渍,果渍,泥渍等在清洁上有困难,需要用助刘清理,不能洗脱的则为大鸡,泥尘,脚印等在洗水后可自行脱去的为细鸡.26.跳线,散口,断缝线,断锁眼,甩锁眼线:属大鸡.27.起蛇,起耳仔:轻微属细鸡,严重属大鸡.28. 领形:领形不正或不圆顺,打风属大鸡.29. 领阔:一定要能过头,且尺寸偏差超过1/2均为不接受.30. 元同包领内子口大(细),有杂纱:属大鸡,.31. 夹底疏孔,夹底缝线松:严重属大鸡,轻微属细鸡.32. 缝骨线露面,缝骨起狗牙,缝骨起蛇,缝骨散口:不接受.33. 膊大(细):单膊度超过1/2以上属大鸡.34. 膊带不留子口:属大鸡.35. 黏边:除夹下地方黏半支属细鸡外,其余地方明显全属大鸡.36. 高低夹,高低脚,高低袋:若缝相差2分内细鸡,超过2分全属大鸡.37.不对坑,不对间,不对花位:超过1分不接受,1分以下属细鸡.38. 吊筒,长短贴:2分内属细鸡,超过2分以上则不接受.39.漏眼:如漏眼全属大鸡,漏半支眼毛少属细鸡,毛多属大鸡.40.用错缝毛,笠错横行,领贴笠高低行,缝线不规则,对位,对花不合:属大鸡,不接受.41. 缝线太松(太紧),缝骨太粗(太鴢),刮边不清,缝位太早(太迟):严重为则大鸡,不接受.42. 缝线不配色,缝骨线不配色:不接受.43.拆线:纱线拉至抽筋属大鸡.拆纱不清,线头不收好属细鸡.44. 收口欠佳,补衣欠佳,漏加针,加针错位属大鸡.45. 挑贴,挑领有高低,不对支或不对间,影响观感属大鸡.46. 挑撞散口,挑撞欠佳,夹底有疏孔,骨位或夹位爆缝线:属大鸡.47.染色不均匀,染污,印错色,阴阳色,色纱,不必要的水痕:属大鸡.48. 谷拉链,错拉链色,拉链尺寸不对码,拉链贴挑撞反缝不合要求:属大鸡.49. 袋高低超过1/4”,歪斜,大小偏差超1/4”,袋缝欠牢固:全属大鸡.50. 烂钮门,钮疵烂钮,用错钮,漏钉钮,钉钮不合要求,钮门不对位或间距不合要求超1/8”:全属大鸡.51. 发霉,有异味,衫未干透,过水不清,搭色掉色:全属大鸡.52. 收腰高低,扭骨,缝骨烫开(疵牙):属大鸡.53. 唛头(吊牌)位置错误,错漏唛头(吊牌),钉唛(吊牌)不合要求:属大鸡.54. 绣花钉珠线太松,太紧,欠弹力,收口欠牢或未打死结,横连珠未分段收口,收口线太长超1.5cm以上:属大鸡.55. 绣花车花图案位置不合要求,高低左右偏差超1/2”以上,歪斜超1/4”,属大鸡.56. 园领套头衫必须查领拉,成人领拉最少12”.六岁以下儿童衫领拉9-1/2”.专业的毛衫英语用词结头Knots粗纱Rough yarn针洞Needle hole色差Color shade色纱Color yarn单毛Single yarn 毛头Yarn end线头Thread end线仔毛Yarn thinness粗细毛Uneven yarn杂毛Mixed yarn花毛Shade yarn织机knitting 错花Wrong pattern花针Tuck stitch走字码Uneven tension起横Uneven course字码不均Uneven knitting tension混毛不均Uneven twist yarn混毛不均,起横纹Uneven yarn and show horizontal stripe缝盘linking挑撞Hand stching 错缝线Wrong linking thread夹缝线起蛇Puckering at armhole seam胸贴不平均Placket not balance笠错横行Incorrect course粘边Selvage not straight缝骨不对齐Seam not match脚边起豆角Hem wringing缝线太紧Linking tension too tight缝线太松Linking tension too loose侧骨手挑太紧,欠水平Hand stitch too tight at side seam not level锁眼起蛇Interline zig-zaging断锁眼线Broken interline铡骨起蛇Over locking line zig-zaging缝法埋堆Linking peaking缝线松紧Uneven linking tension挑撞欠佳Poor hand stitching领子口不均匀Uneven seam of collar落坑Run off锄歪眼Wrong position of needle and point领内子囗不均匀Uneven seam allowance inside neck珠路不均Uneven stitch density铡骨散囗Over- locking seam open起耳仔Pull loop领起耳仔Loose loop at neck拆纱不清Unclear finishing yarn断毛Broken yarn袖囗脚收囗欠佳Poor stitching on cuff or bottom食针Overlapped stitch甩间纱Loose finishing yarn铡骨线露面Wrong tension of over- locking领口不能过头Narrow neck opening单缝线Mis-linking yarn夹花不对称Unmatch armhole fashion mark挑贴跳线Stitching placket skipped stitch膊骨止口太厚Too much seam allowance in shoulderV 领嘴挑线太松Hand stitching tension too loose inside V neck point 侧骨图案不匹配Pattern not match at side seam膊骨和侧骨止口太厚Shoulder seam and side seam too bulky膊带不留子囗No shoulder tape allowance不对坑 (支)Unmatched rib挑贴Stitching placket 挑脚线不牢Insecure blind stitches挑脚线漏挑Blind stitches not securely caught inside断缝线Linking yarn breakage驳线欠佳Poor overlapping stitches坼纱后没拉眼Loops on collar stitch out of trimmingV 领不对支Rib collar of V point not match领内包止口厚Thick seam inside on neck领谷起Bulky at neck哈须 flat lock夹缝线色不对衫身色Armhole linking thread color off body color缝毛与衫身色不对Used wrong sewing color空边.边缘缺棉Empty hem棉絮不均Padded cotton is uneven夹位露缝线Linking seam at armhole is too much visible缝线松紧不均匀Uneven yarn tension 锄高Stitch on the higher position 崩边Broken selvedge 边不直Selvage not straight 对位不符Poor matching on cuff or bottom 锄歪眼Wrong position of needle and point 上领扭纹Twist collar 缝线起蛇Puckering at seam 漏鈒骨线Missing over-locking 爆口Open seam 针数不对Stitch not as specified 线色不配身色Mismatch of thread领边缝线松紧不均匀Uneven linking at neckline 挑错针数Incorrect hand stitch count v领尖不对支Rib collar of v-point not match 拆纱不良导至抽筋Poor trimming 拆纱线没拉眼Loose on collar stitch out of trimming 收漏线头Absence trimming 粉笔痕Chalk mark洗水效果不均匀Uneven washing effect色差/缸差Different lots of shade洗水痕Water streak / Streak mark颜色斑点Color stain油污Oil stain污渍Dirty mark枪水印Cleaning mark霉味Mildew有气味Odor smell灰尘Dusty手感太硬Handfeel too harsh太软Too soft洗水过度Excessive wash洗水不够软Handfeel not soft enough手感太软Handfeel too soft手感比批办稍软Handfeel slightly softer than approved sample染色横痕Uneven dying stripe染色不均 / 有染色印Uneven dye color marks 臭味Bad smell阴阳色Shaded parts去污痕Stain removing mark起毛不够Poor hairy effect霉点Mildew stops手感不够软The handfeel not too soft手感比较鞋Handfeel is slightly harsh手惑太削Thinness handfeel起毛粒Pilling起毡Felting手感不够滑Handfeel not smoothly 什么色手感太鞋Handfeel not too harsh of .color前后幅不同缸Shade lot at front panel and back panel前幅阴阳色Found shade with in front panel袖与衫身不同缸Color shading between body and sleeve洗水后脱色Staining after washing同一件衫内有色差Color shading within one garment配件与衫身之间有色差Color shading between trims and body颜色与批核办不同Shade differs from approved standard纸朴颜色不配合,引起色差Shading caused by poor color interlining matching锈渍Rust mark甩色color fading 颜色太哑/闪color too dull/bright 渗色Bleeding 错缸wrong dye-lot 件染Piece dye 吊染Dip dye 脱色Poor color fastness外观 appearance 领尖高低 Asymmetric collar point领面松 Wrinkles at top collar领面紧 Top collar appears tight领面起泡 Crumples at top collar领外口松 Collar edge appears loose领外口紧 Collar edge appears tight底领伸出 Collar band is longer than collar底领缩进 Collar band is shorter than collar底领里起皱 Wrinkles at collar band facing底领外露 Collar band lean out of collar倘领偏斜 Collar deviates from front center line领窝不平 Creases below neckline后领窝起涌 Bunches below back neckline领卡脖 Tight neckline领离脖 Collar stand away from neck歪领 uneven collar 领不平衡 Unbalance collar领位不对称 Asymmetric collar左右领活不一致 Uneven collar width领尖不对称 Uneven collar point左右前领嘴形状不一样 Uneven lapel shapes前领囗溶位太多 Too much easing at C.F. neckline后颔中太紧 Collar too tight at CB领座扭曲不平顺 Collar band is twisting 领及前领咀不平顺 Fullness at front collar and lapel领圈不元顺 Neckline is not smooth领子装得不平顺 Neck setting not smooth后领圈有高低 High /low back neck领尖长短不一 Uneven length of collar point领尖太钝 / 不平滑 Collar point too blunt / not smooth领尖距太活 / 太窄 Collar spread too wide / narrow高低领尖 Hi-low collar point领歪/领扭曲 Crooked / twisted collar领面布浮 Fullness of top collar领内藏杂物 Some residues inside collar领甩毛 The wool of neck fall down樽领领贻扭曲 Turtle neck collar twisted错领尺寸 Collar size incorrect反领不对称 Collar points not uniform反领谷起 Collar fullness or puckering高低领 High/low collar ends领尖高低 collar points high/low 领形差 Poor neck shape领形差 Poor collarV领边左右不对称 Uneven V-neck sides领卷边大细不均 Uneven rolled edge of neck hole领形不平服 Neck shape not smoothV领底挑囗欠佳 Poor hand stitching at V point of neck 领口起波浪 Neck hole linking is wavy领形欠元顺 Neck hole opening are slant领边内卷 Edge of neck is rolled inV 领不够V V neck point is not Venough领底分针不均 Uneven linking at bottom of neck左右领边有大细 Neck R/L is not same length领垃力太紧 Neck stretch is too narrow后领缝起皱 Puckering at back neck seam领下有疏吼 Loose knitting under neck领卷边缝止口太厚 Neck seam knots is too big领两边起角 The neck opening sides is stick out领拉必须超30cm Neck hole stretch M/B over 30cmV 领咀不够尖 Maze nice sharp finishing of V neck shape卷边不好 poor bowing 领贴过松 collar too loose 领贴过紧 collar too tight 领顶过紧(无弹性) Collar edge is not too inelastic 膊位扭骨 Twist shoulder seam膊位太平.膊斜不够 Shoulder seam too flat膊带太紧- Shoulder tapes are too tight导致膊位起啄 pulls upward and create a point angle膊骨缝线太松 Shoulder seam linking thread is too loose后膊缝线起蛇 Back part linking is wavy膊骨走前 Shoulder seam forward膊骨大细 Shoulder head magnitude大细膊 Uneven shoulder width膊位起啄 Puckering at shoulder point高低膊 Misaligned shoulder高低肩位High/low yoke 膊骨太平Too flat at shoulder seam膊骨太斜Too slant of shoulder seam膊线弯曲不直Shoulder seam not smooth膊头拱起shoulder head not smooth 膊骨起蛇Shoulder seam wavy膊两边不对称Shoulder yoke not balance 膊头缝线不平直Shoulder seam should be straight 膊骨左右不对称Unbalanced R/L shoulders飞机袖Sleeve raise up袖骨走前Underarm seam shown at front袖走后Sleeve running to back袖走前Sleeve running to front前袖骨拉松Too loose at front sleeve seam后袖骨过紧Too tight at back sleeve seam卡夫装得不好Poor cuff setting袖叉装得不好Sleeve placket is not set well袖底缝被拉松Underarm seam was stretched袖缝骨扭Twisted sleeve seam袖扭纹Ribs of sleeve is twist长短袖Uneven sleeve length袖子偏前Sleeve leans to front袖子偏后Sleeve leans to back前袖缝外翻Inseam leans to front袖口起皱Wrinkles at sleeve opening袖里拧 Diagonal wrinkles at sleeve lining扭袖底骨Twisted underarm seam袖肚太大Enlarge sleeve袖咀卷边不均Uneven rolled edge at sleeve袖顶起啄Top sleeve cap pulled inward袖位起镜Pressing mark on sleeve高低袖咀Misaligned at sleeve bottom袖骨哨牙Open seam at sleeve seam袖咀囗挑线太松Loose stitching at sleeve cuff袖咀囗挑线太紧Tight stitching at sleeve cuff袖咀扭曲Knit sleeve cuff twist 袖起波浪The sleeve shape is wavy袖尾凹入Sleeve tail concave into袖尾起啄Puckering at sleeve end袖褶距离不平均Uneven distance of sleeve pleat袖囗没埋口Cuff assembles to sleeve not closed袖摺Pleated seam on sleeve袖错位Sleeve misplaced扭袖Twisted sleeve 袖摺Pleated at sleeve joining袖山起皱Diagonal wrinkles at sleeve cap袖口边不平齐Cuff edge not level 袖底骨扭骨Twisted underarm 袖(膊头位)啄起Sharp point in sleeve head 袖扭骨Twisting sleeve 夹边过紧Tighten armhole tension 高低夹Unmatched armhole seam夹位有疏吼Hole at armhole夹底有疏吼Hole at underarm夹位爆缝Open seam at armhole夹位不直Armhole not straight夹位要顺直Pls keep straight on armhole夹缝不可拉开烫Avoid pressing out of armhole seam夹形两边要对称Keep symmetrical straight on both side of armhole夹顶起啄Pulling cut stitch on top armhole夹位两边不对称Both side of armhole asymmetrical夹圈太紧Tight armhole夹骨起蛇Zigzag seaming at armhole夹骨弯曲起蛇Wavy armhole seam左右夹圈不对称Uneven left / right armhole左右夹圈有溶位不平服Puckering at left / right armhole袖孔不圆顺Armhole setting not smooth夹圈起皱Puckering at armhole 夹缝线哨牙Armhole seam is stretched out by ironing夹顶起啄Top of armhole seam creates a point angle夹圈底的布太多.不平均Uneven fullness at armhole夹圈起皱armhole pucker 夹底缝线松Loose linking threads at under armhole夹位起蛇Puckering at armhole 夹圈散口Armhole fraying 夹底松Loose stitch at underarm袖夹太拱Armhole seam runs arched 夹骨起皱 缩埋Puckering at armhole linking骨位没有完全熨开Seam not fully pressed open缝骨起皱Puckered seam前幅横骨不对称Front horizontal seam not leveled底骨露面Under seam visible骨位起波浪Wavy on seams扭骨Twisted seams侧骨扭Twisting at side seam骨位结尾不平均Seam closures uneven骨位太谷,不平服Fullness on seams骨位末完全拔开间纱线Seam not fully opened before stitching公主骨拉松起泡Too loose at princess seam后公主骨起皱Puckering at back princess seam侧骨车线太紧或太松Too tight or too loose at side seam前中/后中骨太松Too loose at CF/CB seam侧骨起蛇Side seam is wavy侧骨缝线太松Side seam threads is too loose侧骨烫得太开,请补烫Side seam is stretched out by ironing and stick out please re-ironing侧骨扭骨Side seam twist侧骨不顺Uneven side seam 侧骨位要顺直Straight at side seam哨牙Bare linking yarn不对骨位Seam parts at seam not match骨位谷起Seam pucker骨位不对称Mismatched seam骨位外露Raw edge shows处骨走位Out seam run off stitch嵌骨Cover-locking 嵌骨不均匀Uneven cover-locking 嵌骨线太松loose stitch tension 嵌骨线不配色Cover-locking thread not match 嵌骨线不直Cover-locking not straight 缝骨露线Seam grin下裆十字骨错位Unmatched crotch cross 骨位打摺Pleated seam水平缝骨(左右)不对称Horizontal seam not leveled脚弯位不圆顺The bottom curve is not smooth左右开又长短不一Vent length uneven长短脚Uneven leg length衫脚不平均,不对称Uneven hem line脚边不平.起皱Puckering at hem linking衫脚拉得太紧Bottom hem stretch a bit tight衫脚起波浪Bottom hem is wavy衫脚卷边欠平均Uneven rolled edge of bottom hem脚叉不平齐Slit are extremely gaping脚边啄出Hem edge stick out脚纹不顺Wavy hem rib前后脚叉长短Front /back slits is not same length衫脚套针线太紧The hem stretch have a bit tight衫脚套针线起耳仔The hem edge show the yarn loops is linking衫脚罗纹边线太松The hem edge knitting tension is too loose脚罗纹太紧.没有弹性Hem ribs tension is too tight and not elastic enough衫脚不直Bottom not straight脚边不齐Uneven bottom hem衫脚戚起Bottom stretch up下摆丝带太紧,Seam binding stitch tension is too tight使下摆不平顺Causing bottom not smooth折车1/2脚围活窄Uneven folded width at bottom sweep 1/2 hemming衫脚扭Twisted bottom高低脚Uneven edge on cuff or bottom挑脚线露面Bhnd stitching visible严重长短脚Misaligned conspicuous 下脚不够直Bottom hem is not straight下脚扭纹起豆角Twisting hem puckering at hem高低脚Uneven hem横条起波浪Wavy stripes不对格/不对条Mismatched stripe check间条/格仔未对好Pattern matching is not well条纹必须保持同一宽度Little ring stripe must always be of same breadth前幅间色不对称R/L stripe is unmatched at front part间色不平均Uneven stripe侧骨间色不对称Stripe not match at side seam间色两边不对称Unbalance stripe直条不对齐Mismatched plaids 横间不对齐Mismatched stripe 前后幅间色不对齐Front body stripe not match back body stripe对格不良checks not match 间色/格子不对称Stripes / flailS misaligned 颜色组合错误Wrong combo烫衣pressing 烫工差Poor pressing湿气Wet衣服烫过头以致起光痕GMT press too hard cause shiny mark摺痕印Crease mark烧焦印Burn mark水斑点Water spot烫痕Over pressing mark烫衣欠佳,引致有拉链痕,钮痕Zip/button mark made by improper pressing烫朴/压朴效果不佳Poor pressing /fusing of interlining烫斗印Iron mark衫身起镜Mirror effect on body起镜Glaze mark起镜Pressing mark后幅起镜Pressing mark on back part尺寸偏差太大Measurement out of tolerance前中吊起Hiking up at central front后中吊起The back part is pulls upward at center衫身坑条不够直Ribs of body is not straight enough衫纹不直Run of meshes is uneven前幅吊起Hiking at front 前中太短CF facing too short后幅吊起Hiking at back 前幅左石不对称Uneven R/L side of front part前中戚起Front is pulls upwards at front center左右前长不一致Front length uneven罗纹要有弹性Ribs must stay stretch大Larger小Small长Long短ShortDeviation 偏差.误差前中拉链弯曲Curve at CF zip前中拉链溶位太多Too much fullness at CF zipper拉链插位方向错误Wrong way insertion of zipper拉链顶高低Unmatched zipper top露拉链Zipper show out露拉链牙Zipper teeth appeared胸贴露拉链Visible zipper at placker车拉链跳线Skipped stitches at zipper of placket拉链谷起Wavy at zipper拉链不顺Zipper not smooth错拉链Wrongly used zipper拉链贴摺Pleated seam on zipper facing拉链错码Wrong size zipper拉链车不到顶Zipper cannot reach at top拉链车线不直Zipper stitching thread not straight拉链顶/尾有洞Hole at zip top/end拉链装得扭曲Zipper setting is twisting拉链拉不动Zipper not movable 拉链尾处吊起End of zipper is pulls upward 拉链尾处扯开End of zipper is stick out面布车得太贴近拉链fabric to