耐高温铝粉漆(300℃).doc

耐高温铝粉漆（300）Intended Uses用途铝粉漆，用于温度高达300的钢铁设备表面涂装Aluminum paint. Suited for the equipments with the temperature up to300ProductDescription产品简介作一般用途的油脂性铝粉漆Oil aluminum paint for common use.ProductInformation产品数据Volume Solids 固体份37%Dry Film Thickness干膜厚度25um microns equivalent to 68 microns of wet film25微米,相当于68微米的湿膜厚。Theoretical Coverage 理论涂布率14.5m2 /Kg based on the stipulated volume solids and the dry film thick 25 microns.14.5平方米/公斤,以规定体积的固体份和25微米干膜厚计Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Application Details施工详述Mix Radio 混合比One package 单罐装Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Suitable 适用 Conventional Spray 传统喷涂 Recommended 推荐采用Thinner 稀释剂 Unnecessary, in normal, If need, Use C002 一般不需要，如果需要用C002Cleaner 油漆设备清洗剂 C002Pot Life 使用期 Not limit 不限制Storage 贮存期 One year 一年Drying time 干燥时间SubstrateTemperature底材温度,Touch Dry表干（min）Hard Dry硬干（H）Over coating Interval覆涂间隔Mix最短Max最长2233542172242416hours小时10hours 小时6hours 小时Not limit 不限Storage andHandling贮存与管理Storage 贮存 Store in cool and dry conditions 贮存于阴凉干燥处 Pack size 包装规格 20Kg in 20 liter container 20公斤装于20公升容器中Flash Point 闪点 33 高于33Specific Gravity 比重 1.00Kg/L 1.00公斤/公升 Specification and Surface preparation技术要求及表面处理Applied to properly primed surface commonly, the primed surface must be clean, dry and none of dirt, remove dirt. With hard bristle brush, then wash out any soluble salt deposits with fresh water通常用于已涂底漆的表面上，此底漆的表面必须干燥清洁、并无污物，用硬刷或水去除表面污垢，然后用清水洗去可溶盐份。Limitations限制Typical thickness, must be no more than 25mocrons each coat. If applied to substrate for high temperature. One coat (15 microns) shall be coated only, otherwise it may bring about bubble, should be maintained at room temperature when over-coating.每道不得超过25微米厚，如用于高温底材时，则只允许一道（15微米厚），否则易产生起泡，而覆涂时其底材需保持室温。 Safety Precautions 安全措施The product must be used in painting area by professionals. When painting, please be sure to refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying the product.The product is a kind of solvent-based paint. In order to avoid the accident or dangerous occurrence, minimal safety precaution, as follow, should be down.The paint contains volatile solvent and it is flammable, So must keep away from sparks and open flames. No smoking at workplace, Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid product sparks. Enough ventilation is necessary at application sites. In order to remove any danger of explosion, must keep the ratio of gas / air is less than 10 %, Usually 200 m3of ventilation quantity per 1 Kg solvent (according to the solvent) is necessary, it canMaintain the minimum explosive limit. Take effective precautions to prevent skin and eye contact with the coating (such as the use of overalls, gloves, goggles, face shields and protective oil coating and so on). If paint gets in touch with skin,If accidental skin contact with the product, please use fresh water and soap or an appropriate industrial cleaning agents thoroughly cleansed. In case of eyes being contaminated, rinse with fresh water for 10 min at least and give medical treatment immediately.During painting, it is recommended to wear face shields to prevent inhalation of paint mist and harmful gases.Especially in poorly ventilated environment, it is more necessary.Finally, be handled with care so as not to waste paint barrels of pollution of the environment.NOTICE: If consumers have not taken effective safety precautions (Refer to the specification), our company will NOT be responsible for any accident. 本产品必须由专业人员在工业场所使用。使用时请务必参照本说明书以及相关健康安全手册。若客户在使用本产品前,未能详细了解本产品的相关健康安全知识,请与本公司人员联系。该涂料为溶剂型涂料，为避免事故或危险发生，应采取最低限度的安全措施如下：此涂料为易燃物,并含有挥发性易燃溶剂，故必须远离火星和明火。严禁在作业场所吸烟，并应该采取有效措施，防止火星产生(如采用防爆电器设备，杜绝静电积累,避免金属撞击等)。 施工场所应尽量保持良好通风。为消除使用过程中的爆炸隐患,应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10 %,通常每千克溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10 %的工作环境。 采取有效措施，防止皮肤和眼睛与涂料直接接触(