丙烯酸聚氨酯与环氧树脂涂料对比说明.doc

涂料说明丙烯酸聚氨酯涂料是一种性能优越的涂料，其特点是除了耐水、耐海水、耐沸水、耐一般酸、碱化学品外，还具有突出的耐石油性，漆膜硬韧，耐磨性特强，不像环氧树脂面漆在大气中易产生粉化、褪色等现象。涂料名称性能对比环氧树脂涂料丙烯酸聚氨酯涂料外用耐久性中优耐盐雾性良优耐溶剂性良优耐化学品性良良柔韧性中优耐冲击性中优附着力优优施工性良优光泽度半光高光 江苏力丰特种涂料有限公司 2009.06.15Coating DescriptionAcrylic polyurethane coating is a superior performance of the coating. Its characteristics are water-resistant, seawater-resistant, boiling water-resistant, the general acid-resistant and alkali-resistant chemicals, and its oil-resistant is very salient. The film are hard and wear-resistant, it does not like the epoxy resin top coatings film which will be pulverization and faded in the air.Coating namePerformance comparisonEpoxy resin coatingAcrylic polyurethane coatingExternal durabilityMediumExcellentSalt spray resistanceGoodExcellentSolvent resistanceGoodExcellentChemical resistanceGoodGoodFlexibilityMediumExcellentImpact resistanceMediumExcellentAdhesionExcellentExcellentConstructionGoodExcellentGlossinessHalf lightHigh light Jiangsu Lifeng special coatings Co., Ltd. 2009.06.15BS52-12丙烯酸聚氨酯面漆（双组份）产品组成 由含羟基高性能树脂为基料，加入耐候性颜料、助剂等组成甲组份，以HDI-缩二脲为乙组份组成的双组份涂料。 设计用途 用于船舶、桥梁、海上设施、化工和石化厂等钢结构作防腐面漆。 主要特性 良好的物理机械性能，附着力强，硬度高，漆膜防腐性能优异，耐湿热，耐酸碱，耐盐雾、保光、保色性及耐候性突出，长期重涂性极佳。 物理参数 颜色：各色 密度：1.261.37kg/L 理论用量：0.120.15kg/ 漆膜厚度：湿膜厚度7595m，干膜厚度4050m 闪点：约27 干燥时间：（25），表干0.5h，实干24h，完全固化7d 贮存时间：甲组份一年，乙组份半年 施工参数 配比：甲组份：乙组份=10：1 熟化时间：（232）20min 适用期：（232）8h(超过8h后严禁加入稀料后使用) 涂装方法：高压无气喷涂、手工刷涂、滚涂 稀释剂及稀释比： 105聚氨酯涂料稀释剂，5% 涂装间隔： 0：最短3小时，25：最短2小时，35：最短1小时，最长无限制 表面处理：如前道漆面已经污染，应用适当的方法除去油脂、灰尘；也可用本漆稀释剂擦洗 施工条件：环境温度为0-40，空气相对湿度应80%，工件表面湿度高于露点温度3以上 前道配套涂料：H06环氧富锌底漆、H53-6环氧云铁防锈漆，S53-85聚氨酯云铁中间漆 声 明 本说明书有关数据是根据试验和使用经验积累的，可作为施工指南，本产品只适用于专业用途，指定以外的用途和我们不了解情况下的施工，我们只保证涂料本身的质量。BS52-12 Acrylic Polyurethane Topcoat (2K)Component Component A: hydroxyl acrylic resin as binder, pigment, additive, etc. Component B: HDI allophanamide.Properties Good physical and mechanical property, adhesion, hardness, excellent anticorrosion, gloss retention and color retention, resistant to humidity, heat, acid, alkali, salt fog and weather.Application Anticorrosive topcoat of marine, bridge and steel structures.Physical ParameterColor: All colorsSpecific Gravity: Approx, 1.26-1.37 kg/LTheoretic Dosage: 0.12-0.15 /Flash Point: 27CDrying Time: 25C, Dust-Free: 0.5 h, Hard Drying: 24 h, Fully Curing: 7 d Storage: Component A: 1 year, Component B: 6 monthsFilm Thickness: WFT: 75-95m DFT: 40-50mApplication Parameter:Formula Ratio: Component A: Component B=10: 1Curing Time: 25C, 20 minPot Life: 2,5C, 8 hCoating Method: High-pressure airless spray, hand brushing, roll coating. Diluent/Dilution Ratio: 105 acrylic polyurethane coatings diluent, 5%Coating Interval: 0C, Min. 3 h, Max. 48 h; 2,5C, Min. 2 h, Max. 24 h; 35C, Min. 1 h, Max. 24 h.Surface Treatment: If the pre-paint is stained, the grease and dust should be removed, which could also be scrubbed away by diluent of this paint.Pre-Coat Accessory Coatings: H-06 epoxy zinc rich primer, H53-6 epoxy MIO anticorrosion paint, S53-85 polyurethane MIO inter-paint.Claim: The data in this Specification is derived from experiments and practical applications, and can be regarded as a guide for application. The title product is only for specialty application. Otherwise we only guarantee the quality of the said coatings itself if it is used in other sectors undescribed herein or fresh sectors.H52-68 各色环氧防腐面漆产品组成 由环氧树脂，加入各种防腐蚀颜料、混合溶剂、触变剂与固化剂组成。 设计用途 适用于化工设备及钢构件、设备等作防腐面漆。 主要特性 具有优异的化学稳定性，耐热、耐油及耐各种介质腐蚀性能。 物理参数 颜色：各色 密度：1.30kg/L 理论用量：0.16kg/ 漆膜厚度：湿膜厚度125m，干膜厚度75m 闪点：约22 干燥时间：（23），表干4h，实干48h，完全固化7d 贮存时间：一年 施工参数 配比：甲组份：乙组份=10：1（重量比） 熟化时间：（23）30min 适用期：（23）8h，低于5时不宜施工 涂装方法：高压无气喷涂、手工刷涂、滚涂 稀释剂及稀释比：102环氧树脂涂料稀释剂，5% 涂装间隔： 0：最短3小时，25：最短2小时，35：最短1小时，最长无限制 表面处理：前道漆的涂装间隔时间已经超过最长涂装间隔，应将前道漆打磨至表面有粗糙度。 前道配套涂料：环氧类防锈漆 声 明 本说明书有关数据是根据试验和使用经验积累的，可作为施工指南，本产品只适用于专业用途，指定以外的用途和我们不了解情况下的施工，我们只保证涂料本身的质量。H52-68 Epoxy Anticorrosive Topcoat of All ColorsComponent Epoxy resin, anticorrosive pigment, mixed solvents, thixotropic agent, curing agent, etc.Properties Excellent chemical stability and resistance to heat, oil and corrosion resistance for various mediumApplication Anticorrosive topcoat for steel structures or equipment.Physical ParameterColor: All colorsDensity: Approx. 1.30 kg/LFilm Thickness: WFT: 125m DFT: 75m Theoretic Dosage: 0.16 kg/Flash Point: 22CDrying Time: 23 C, Dust-Free: 4 h, Hard Drying: 48 h, Fully Curing: 7 d Storage: 1 yearApplication Parameter:Formula Ratio: Component A: Component B=10: 1 (weight ratio)Curing Time: 23C, 30 minPot Life: 23 C, 8 h, not applicable below5CCoating Method: High-pressure airless spray, hand brushing, roll coatingDiluent/Dilution Ratio: 102 epoxy resin coatings diluent, 5%Surface Treatment: The coating interval of pre-paint has exceeded the max coating interval, so the pre-paint should be polished to be crude.Recommended Layers: 1-2 layers (high-pressure airless spray), 120-150m DFT.Pre-Coat Accessory Coatings: Epoxy anticorrosion paint.Coating Interval: 23 C : Min. 24 h, Max. 3 dClaim: The data in this Specification is derived from experiments and practical applications, and can be regarded as a guide for application. The title product is only for specialty application. Otherwise we only guarantee the quality of the said coatings itself if it is used in other sectors undescribed herein or fresh sectors.Jiangsu Lifeng special coatings Co., Ltd. quality guaranteeCoating inspection reports NO.:0906-036Coating model and nameH52-68 Epoxy RAL6018 top coatingProduct LotA:20090615B:20090616Amount5000 (kg)Test StandardQ/320412LFT006-2008 A:B=10:1Test itemsStandardSpecificationsTest resultsFilm colour and appearance (visual)VisualFilm are smoothRAL6018 film are smoothViscosity (s)GB/T172380qualificationFineness (m)GB/T675360qualificationDry timeDust-free (h)GB/T17284qualificationHard dry (h)GB/T172848qualificationAdhesion (level)GB/T17202qualificationFlexibility (mm)GB/T17311qualificationImpact strength (cm)GB/T173250qualificationGloss (%)/Hiding power (g/)/Conclusion:qualificationTest Review Audit Test date 06.2009 Test units sealJiangsu Lifeng special coatings Co., Ltd. quality guaranteeCoating inspe