长江750摩托改装全过程（组图）.doc

装了台普通变速箱，顺便把图片传给大家。希望在某些时间对大家有所帮助。倒档变速箱有个别不同之处，来日有机会在上图给大家，网速问题单这些搞了3个多小时 还有个别图片喽拍，比如2轴的轴承安装，添加垫片等等我回找时间补拍。忘见谅首先先准备必要的配件。BigBull_DSC05282.JPG (101.7 KB)2008-10-23 18:59BigBull_DSC05283.JPG (105.03 KB)2008-10-23 18:59然后先安装机壳内部的爪的限动器BigBull_DSC05284.JPG (107.24 KB)2008-10-23 18:59BigBull_DSC05285.JPG (76.57 KB)2008-10-23 18:59下一步安装缓冲器组件，也就是变速箱放油口旁边挂刹车弹簧的那个东西，可不是单单起着挂刹车弹簧的作用哦BigBull_DSC05286.JPG (85.41 KB)2008-10-23 18:59BigBull_DSC05287.JPG (88.29 KB)2008-10-23 18:59BigBull_DSC05288.JPG (85.96 KB)2008-10-23 18:59下一步安装启动轴组件BigBull_DSC05290.JPG (82 KB)2008-10-23 18:59在启动轴上先安装制动弹簧和制动销子，装上启动千斤块在此我多说一下。一般遇到脚启动启动杆打滑大部分都是因为启动千斤块磨损而造成的，可以把启动千斤反过来装上就ok了看下图BigBull_DSC05292.JPG (99.27 KB)2008-10-23 18:59BigBull_DSC05294.JPG (80.68 KB)2008-10-23 18:59特意找了快磨损的启动千斤，看下图BigBull_DSC05298.JPG (94.3 KB)2008-10-23 18:59BigBull_DSC05299.JPG (115.71 KB)2008-10-23 18:59BigBull_DSC05295.JPG (92.67 KB)2008-10-23 18:59下面装上启动齿轮，及启动齿轮套穿入销钉。装入箱体BigBull_DSC05296.JPG (111.97 KB)2008-10-23 20:01BigBull_DSC05297.JPG (70.25 KB)2008-10-23 20:01接下来在机壳后部打上密封胶我的放时间长了，浓度高摸不开了 ，记得加上纸垫，装入启动轴后衬套BigBull_DSC05302.JPG (130.44 KB)2008-10-23 20:01BigBull_DSC05301.JPG (96.5 KB)2008-10-23 20:01BigBull_DSC05303.JPG (114.25 KB)2008-10-23 20:01下面装上小草帽油封。装山衬套压板上紧螺丝BigBull_DSC05304.JPG (111.59 KB)2008-10-23 20:01BigBull_DSC05305.JPG (112.64 KB)2008-10-23 20:01下一步装上主轴档油盘，滚珠轴承。主轴下入机壳BigBull_DSC05306.JPG (79.88 KB)2008-10-23 20:06BigBull_DSC05307.JPG (127.92 KB)2008-10-23 20:06BigBull_DSC05308.JPG (114.64 KB)2008-10-23 20:06接下来排列二轴档位齿轮。1首先放入档油盘垫片装然后放入一档齿轮。最大个那个。 。小齿朝上BigBull_DSC05313.JPG (99.38 KB)2008-10-23 19:56BigBull_DSC05314.JPG (118.2 KB)2008-10-23 19:562接下来装入一档与二档齿之间的二轴连接齿轮和结合套BigBull_DSC05323.JPG (129 KB)2008-10-23 20:06BigBull_DSC05325.JPG (89.06 KB)2008-10-23 20:06BigBull_DSC05324.JPG (135.23 KB)2008-10-23 20:063放入二档齿轮。注意小齿朝下BigBull_DSC05326.JPG (129.5 KB)2008-10-23 20:064放入、三档齿轮。相反小齿朝上BigBull_DSC05327.JPG (124.99 KB)2008-10-23 20:115放入三档和四档之间的链接齿轮和结合套BigBull_DSC05328.JPG (114.55 KB)2008-10-23 20:11BigBull_DSC05329.JPG (116.84 KB)2008-10-23 20:116放入四档齿轮。小齿朝下。穿入二轴BigBull_DSC05331.JPG (112.25 KB)2008-10-23 20:11BigBull_DSC05332.JPG (112.65 KB)2008-10-23 20:11BigBull_DSC05333.JPG (139.31 KB)2008-10-23 20:11装入主轴轴承BigBull_DSC05335.JPG (105.31 KB)2008-10-23 20:23上密封胶加垫子下入变速箱前盖BigBull_DSC05337.JPG (131.6 KB)2008-10-23 20:23别忘了二轴上面这个档油盘哦BigBull_DSC05338.JPG (92.88 KB)2008-10-23 20:23下入前盖。砸入前盖定位销，上紧螺丝BigBull_DSC05339.JPG (124.87 KB)2008-10-23 20:23BigBull_DSC05340.JPG (103.27 KB)2008-10-23 20:23BigBull_DSC05341.JPG (94.23 KB)2008-10-23 20:23接下来装入启动弹簧，必须要给启动弹簧上劲。大概一圈半吧。然后拧上螺丝BigBull_DSC05345.JPG (85.19 KB)2008-10-23 20:51BigBull_DSC05346.JPG (127.82 KB)2008-10-23 20:51BigBull_DSC05347.JPG (121.83 KB)2008-10-23 20:51安装拨叉及拨叉穿杆BigBull_DSC05342.JPG (115.14 KB)2008-10-23 20:51BigBull_DSC05344.JPG (99.75 KB)2008-10-23 20:51安装右盖。规板组件BigBull_DSC05350.JPG (112.42 KB)2008-10-23 20:51BigBull_DSC05352.JPG (112.15 KB)2008-10-23 20:51BigBull_DSC05353.JPG (109.57 KB)2008-10-23 20:51接下来安装脚档和左盖组合。首先把手档板到空档位置。然后旋转辣轮。把变速制动爪上牙对准辣轮上第二个齿。下牙自然对准辣轮下第一个牙进行安装。下2图我找旧的拍了详细图片BigBull_DSC05354.JPG (77.87 KB)2008-10-23 21:49BigBull_DSC05355.JPG (101.46 KB)2008-10-23 21:49BigBull_DSC05357.JPG (88.12 KB)2008-10-23 21:49一轴油封安装，先装入纸垫。然后装入一轴隔离衬套。然后装入油封BigBull_DSC05361.JPG (52.66 KB)2008-10-23 22:02BigBull_DSC05363.JPG (80.02 KB)2008-10-23 22:02BigBull_DSC05364.JPG (72.58 KB)2008-10-23 22:02安装变速器接触器。首先装入油封。装入接触器圆盘。记住上圆盘固定螺母时必须记住多打点胶进去，避免漏油。此处漏油就是长江的弊病BigBull_DSC05374.JPG (75.42 KB)2008-10-23 22:02BigBull_DSC05366.JPG (62.83 KB)2008-10-23 22:02BigBull_DSC05367.JPG (96.42 KB)2008-10-23 22:02装上附件。完工BigBull_DSC05370.JPG (66.49 KB)2008-10-23 22:02BigBull_DSC05371.JPG (71.95 KB)2008-10-23 22:02BigBull_DSC05372.JPG (77.19 KB)2008-10-23 22:02BigBull_DSC05373.JPG (61.88 KB)2008-10-23 22:02 本帖最后由 独自飘流 于 2008-10-23 22:09 编辑 附件BigBull_DSC05296.JPG (111.97 KB) 2008-10-23 19:29 BigBull_DSC05297.JPG (70.25 KB) 2008-10-23 19:29 BigBull_DSC05302.JPG (130.44 KB) 2008-10-23 19:29 BigBull_DSC05301.JPG (96.5 KB) 2008-10-23 19:29 BigBull_DSC05303.JPG (114.25 KB) 2008-10-23 19:29 BigBull_DSC05304.JPG (111.59 KB) 2008-10-23 19:29 BigBull_DSC05305.JPG (112.64 KB)