国际电工委员会IEC标准.doc

国际电工委员会IEC标准IEC 60331-11：着火条件下电缆的测试电路完整性第11部分：着火条件下电缆的测试电路完整性第11部分：仪器火焰温度至少750条件下的单独燃烧IEC 60331-11：Tests for electric cables under fire conditions Circuit integrity Part 11: Apparatus Fire alone at a flame temperature of at least 750 DegreesAbstract摘要This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire alone where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of at least 750 C.It also provides in annex A the method of verification of the burner and control system used for the test.IEC 60331-21：着火条件下电缆的测试 电路完整性 第21部分:程序和要求 额定电压0.6/1.0kV及以下的电缆IEC 60331-21：Tests for Electric Cables under Fire Conditions - Circuit Integrity - Part 21: Procedures and Requirements - Cables of Rated Voltage up to and Including 0.6/1.0 kVAbstract摘要This part of IEC 60331 specifies the test procedure and gives the performance requirement, including a recommended flame application time, for cables of rated voltage up to and including 0,6/1,0 kV required to maintain circuit integrity when subjected to fire under specified conditions.It describes the means of sample preparation, continuity checking arrangements, electrical testing procedure, method of burning the cables and gives requirements for evaluating test results.It is intended to cover low voltage power cables, and control cables with a rated voltage.IEC 60331-23：着火条件下电缆的测试 电路完整性 第23部分:程序和要求 电数据电缆IEC 60331-23：Tests for Electric Cables under Fire Conditions - Circuit Integrity - Part 23: Procedures and Requirements - Electric Data CablesAbstract摘要This part of IEC 60331 specifies the test procedure and gives the performance requirement, including a recommended flame application time, for electric data cables required to maintain circuit integrity when subjected to fire under specified conditions.It describes the means of sample preparation, continuity checking arrangements, electrical testing procedure, method of burning the cables and gives requirements for evaluating test results.It covers electric data cables which have no rated voltage and are used for extra low voltage circuits.IEC 60331-25：着火条件下电缆的测试 电路完整性 第25部分:程序和要求 光缆IEC 60331-25：Tests for Electric Cables under Fire Conditions - Circuit Integrity - Part 25: Procedures and Requirements - Optical Fibre CablesAbstract摘要This part of IEC 60331 specifies the test procedure, and gives the performance requirement, including a recommended flame application time, for optical fibre cables required to maintain circuit integrity when subjected to fire under specified conditions. It describes the means of sample preparation, continuity checking arrangements, optical testing procedures, the method of burning the cables and gives requirements for evaluating test results.IEC 60332-1：着火条件下电缆和光缆的测试.第1部分:单根绝缘电线或电缆垂直火焰蔓延的测试IEC 60332-1：Tests on Electric Cables Under Fire Conditions Part 1: Test on a Single Vertical Insulated Wire or CableIEC 60332-2：着火条件下电缆的测试 第2部分:单根小垂直绝缘铜电线或电缆的测试IEC 60332-2：Tests on Electric Cables Under Fire Conditions Part 2: Test on a Single Small Vertical Insulated Copper Wire or CableAbstract摘要Specifies the procedure for testing the resistance to vertical flame propagation for a single small vertical electrical insulated conductor or cable, or optical cable, under fire conditions. The apparatus is given in IEC 60332-2-1. This standard gives the procedure for testing small optical fibre cables or a small insulated conductor or cable when the method specified in IEC 60332-1-2 is not suitable because some small optical fibre cables may break or small conductors may melt during the application of the flame. The recommended range of application is for the testing of small single insulated conductors or cables of less than 0,5 mmY cross-section. NOTE Since the use of insulated conductor or cable which retards flame propagation and complies with the recommended requirements of this standard is not sufficient by itself to prevent propagation of fire under all conditions of installation, it is recommended that wherever the risk of propagation is high, for example, in long vertical runs of bunches of cables, special installation precautions should also be taken. It cannot be assumed that because the sample of cable complies with the performance requirements recommended in this standard, that a bunch of cables will behave in a similar manner. 以上资料由防火资源网（）防火测试中心整理或发布，需了解更多请登录官网，谢谢。IEC 60332-3：着火条件下电缆的测试 第3部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试IEC 60332-3：Tests on Electric Cables under Fire Conditions Part 3: Tests on Bunched Wires or CablesIEC 60332-3-21：着火条件下电缆的测试 第3-21部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试 种类A F/RIEC 60332-3-21：Tests on Electric Cables Under Fire Conditions - Part 3-21: Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Category A F/RIEC 60332-3-22：着火条件下电缆的测试 第3-22部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试 种类AIEC 60332-3-22：Tests on electric and optical fibre cables under fire conditions Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables Category AAbstract摘要The series of International Standards covered by Parts 3-10, 3-21, 3-22, 3-23, 3-24 and 3-25 of IEC 60332 specifies methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables, electrical or optical, under defined conditions.NOTE For the purpose of this standard the term electric wire or cable covers all insulated metallic conductor cables used for the conveyance of energy or signals.The test is intended for type approval testing. The requirements for the selection of cables for testing are given in annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure may be used to demonstrate the cables ability to limit flame spread.This part of IEC 60332 covers category A and relates to cables installed on the test ladder to achieve a nominal total volume of non-metallic material of 7 l/m of test sample. The flame application time is 40 min. The method of mounting uses the front of the ladder, a standard or wide ladder being used for cables having a conductor cross-section greater than 35 mm according to the number of test pieces required, and a standard ladder for conductor cross-sections 35 mm and smaller. The category is intended for general use where high volumes of non-metallic material are required to be evaluated.以上资料由防火资源网（）防火测试中心整理或发布，需了解更多请登录官网，谢谢。IEC 60332-3-23：着火条件下电缆的测试 第3-23部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试 种类BIEC 60332-3-23：Tests on electric and optical fibre cables under fire conditions Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables Category BIEC 60332-3-24：着火条件下电缆的测试 第3-24部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试 种类CIEC 60332-3-24：Tests on electric and optical fibre cables under fire conditions Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables Category CAbstract摘要The series of International Standards covered by Parts 3-10, 3-21, 3-22, 3-23, 3-24 and 3-25 of IEC 60332 specifies methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables, electrical or optical, under defined conditions.NOTE For the purpose of this standard, the term electric wire or cable covers all insulated metallic conductor cables used for the conveyance of energy or signals.The test is intended for type approval testing. The requirements for the selection of cables for testing are given in annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure may be used to demonstrate the cables ability to limit flame spread.This part of IEC 60332 covers category C and relates to cables installed on the test ladder to achieve a nominal total volume of non-metallic material of 1,5 l per metre of test sample. The flame application time is 20 min. The method of mounting uses the front of the standard ladder. The category is intended for general use where low volumes of non-metallic material are required to be evaluated.IEC 60332-3-25：着火条件下电缆的测试 第3-25部分:垂直安装的成束电线或电缆的垂直火焰蔓延的测试 种类DIEC 60332-3-25：Tests on electric and optical fibre cables under fire conditions Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables Category DAbstract摘要The series of International standards covered by Parts 3-10, 3-21, 3-22, 3-23, 3-24 and 3-25 of IEC 60332 specifies methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables, electrical or optical, under defined conditions. NOTE For the purpose of this standard, the term electric wire or cable covers all insulated metallic conductor cables used for the conveyance of energy or signals. The test is intended for type approval testing. The requirements for the selection of cables for testing are given in annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure may be used to demonstrate the cables ability to limit flame spread. This part of IEC 60332 covers category D and relates only to small cables of overall diameter 12 mm or smaller installed on the test ladder to achieve a nominal total volume of non-metallic material of 0,5 l/m of test sample. The flame application time is 20 min. The method of mounting uses the front of the standard ladder in touching formation only. The category is intended for use with small cables where very low volumes of non-metallic material are required to be evaluated. IEC 60695-1-1：火灾危险测试 第1-1部分:电工产品火灾危险评定指南 通用指南IEC 60695-1-1：Fire Hazard Testing - Part 1-1: Guidance for Assessing the Fire Hazard of Electrotechnical Products - General GuidelinesAbstract摘要This part of IEC 60695 provides guidance for assessing the fire hazard of electrotechnical products (see clause 4) and for the resulting development of fire hazard testing (see clause 5) as related directly to harm to people, animals or property. Products, as defined in this standard, relate to materials, components or complete end-use products. This standard is intended as guidance to IEC committees, and should be used with respect to their individual applications. Attention is drawn to the principles in IEC Guide 104, and to the role of committees with safety pilot functions and safety group functions. IEC 60695-2-2：火灾危险测试 第2部分:测试方法 第2节:针焰测试IEC 60695-2-2：Fire Hazard Testing Part 2: Test Methods Section 2 - Needle-Flame TestAbstract摘要Specifies a needle-flame test to stimulate the effect of small flames which may result from fault conditions within the equipment, in order to assess by a simulation technique the fire hazard.以上资料由防火资源网（）防火测试中心整理或发布，需了解更多请登录官网，谢谢。IEC 60695-2-3：火灾危险测试 第2部分:测试方法 第3节:用发热器的不良连接测试IEC 60695-2-3：Fire Hazard Testing Part 2: Test Methods Bad-Connection Test with HeatersAbstract摘要Simulates the thermal stresses which may be produced by fault conditions in screw connections having a rated current not exceeding 63 A, and which are made during installation, servicing or maintenance. Applicable to equipment, sub-assemblies and components.IEC 60695-2-4：火灾危险测试 第2-4部分:测试方法-:扩散型和预混合型火焰测试方法IEC 60695-2-4：Fire hazard testing - Part 2: Test methods - Section 4: Diffusion type and premixed type flame test methodsIEC 60695-2-11：火灾危险测试 第2-11部分:基于灼热/发热丝的测试方法 最终产物的灼热丝易燃性测试IEC 60695-2-11：Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire flammability test method for end-productsAbstract摘要This part of IEC 60695 specifies the details of the glow-wire test to be applied to end-products for fire hazard testing. For the purpose of this standard, end-product means electro technical equipment, its subassemblies, and components.IEC 60695-2-12：火灾危险测试 第2-12部分:基于灼热/发热丝的测试方法 材料的灼热丝易燃性测试IEC 60695-2-12：Fire Hazard Testing - Part 2-12: Glowing/Hot-Wire Based Test Methods - Glow-Wire Flammability Test Method for MaterialsAbstract摘要Specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI).The test results make it possible to provide a relative comparison of various materials according to their ability to extinguish flames on removal of the electrically heated glow-wire and their ability not to produce flaming or glowing particles capable of spreading fire to a specified layer of wrapping tissue placed below.The test method is not valid for determining the flammability of complete items of equipment, since the dimensions of the insulating systems or combustible parts, the design and heat transfer to adjacent metallic or non-metallic parts, etc., greatly influence the flammability of the materials used therein. In addition to this, it is not valid for determining fire behaviour and fire hazard of equipment.IEC 60695-2-13：火灾危险测试 第2-13部分:基于灼热/发热丝的测试方法 材料的灼热丝起燃性测试IEC 60695-2-13：Fire Hazard Testing - Part 2-13: Glowing/Hot-Wire Based Test Methods - Glow-WIre Ignitability Test Method for MaterialsAbstract摘要This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT).The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested materiala) does not ignite, orb) if sustained and continuous flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed.This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 to judge the ability of materials to meet the requirements of IEC 60695-2-11.NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests may allow a reduction of end product testing.以上资料由防火资源网（）防火测试中心整理或发布，需了解更多请登录官网，谢谢。IEC 60695-2-20：火灾危险测试 第2部分:基于灼热/发热丝的测试方法 第20节:材料的热丝圈可点火性测试IEC 60695-2-20：Fire hazard testing - Part 2: Glowing/Hot wire based test methods - Section 20: Hot-wire coil ignitability test on materialsAbstract摘要It is applicable to solid electrical insulating materials. It is intended to provide a relative comparison of the behaviour of various materials according to the time taken to ignite thespecimen during application of heat from an electrically heated coil as an ignition source.IEC 60695-5-2：火灾危险测试-第5-2部分：燃烧后的腐蚀物-测试方法的摘要及有关问题IEC 60695-5-2：Fire hazard testing - Part 5-2: Corrosion damage effects of fire effluent - Summary and relevance of test methodsAbstract摘要Gives a summary of the test methods that are used in the assessment of the corrosivity of fire effluent. It presents a brief summary of test methods in common use, either as international standards or national or industry standards. It includes special observations on their relevance, for electrotechnical products and their materials, to real fire scenarios and gives recommendations on their use.IEC 60695-6-31：火灾危险测试-第6-31部分：烟密度-小规模测试-材料IEC 60695-6-31：Fire Hazard Testing - Part 6-31: Smoke Obscuration - Small-Scale Static Test MaterialsAbstract摘要Applicable to flat, solid non-metallic specimens of materials used in electro technical products. This method is not applicable to the testing of non-flat products such as insulated wires and cables, as it is not possible to obtain a satisfactory distribution of heat flux with such products. May not be applicable for materials which melt and flow away from the direct impingement of heat flux and do not give a smoke emission, which is representative of current knowledge from real fire situations. The purpose of this method is to determine, under specific experimental conditions, the optical density of smoke produced by materials exposed vertically to a radiant heat source with or without the application of a pilot flame in a closed chamber (i.e. without air-change). Has the status of a basic safety publication in accordance with IEC Guide 104.IEC 60695-7-3：火灾危险测试-第7-3部分：燃烧后的毒性.测试结果的使用和说明IEC 60695-7-3：Fire hazard testing Part 7-3: Toxicity of fire effluent Use and interpretation of test resultsAbstract摘要Concerns laboratory tests used to measure the toxic components of the fire effluent from either electro technical products or materials used in electro technical products. It provides guidance on the use and interpretation of results from such tests. It discusses currently available approaches to toxic hazard assessment consistent with the approach of ISO TC 92 SC 3, as set out in ISO/TR 9122-1 to 9122-6, ISO 13344 and ISO/TS 13571. It also provides guidance on the use of toxic potency data in hazard assessment and on principles which underlie the use of combustibility and toxicological information in hazard assessment.The methods described are applicable to data concerning both the incapacitating effects and the lethal effects of fire effluents.The structure of this technical specification remains essentially the same as the first edition but has been usefully expanded in all areas to further clarify