ST-16020-6--产品规格书--PT--中性 2(1) 2.doc

产品规格书 产 品 名非晶硅太阳能电池品牌名称制 造 商产 地产品规格160*20*1.1 mm产品型号16020-6产 品 规 格 书-参 数 表Specification -Paranmeter Specification1、 Name &Model 名称、型号11：Name名称SOLAR CELLS12：Model型号 16020-62、 性能参数项 目参 数2.1尺寸160*20*1.1 mm 公差：0.2mm2.2开路电压最小值2.5V典型值3.0V2.3短路电流最小值55uA典型值60uA 2.4负载特性最小值2.0V典型值2.2V2.5工作温度-5452.6保存温度、温度-2060 湿度75%2.7使用照度范围0100000Lux2.8测试条件FL 200Lux、25注：1、 产品出厂时以：“工作电压为检测标准”3、工作电压（Vop）和工作电流（Iop）测试原理图：4、 产品图附 加 说 明- Additional instructions5、Outgoing inspection (成品检验)51Inspection method (检验规定)Outgoing inspections shall be based on random sampling, Normal inspxtion by single sampling based on MIL-STD-105D shall be applied.(成品检验采取随机抽样方案，抽样方安按MIL-STD-105D执行)52Outgoing inspection results shall be usually tested by the inspection result table. (成品检验结果将以测试报告表/合格证形式提供)6、Regulation for product solder: （成品可焊性检验规则）61 Purpose（目的）Let the product including the condition for lead-free soldering be standard and ensure the sodering quality of product in the factory (out of the factory)。（规范公司产品可焊性试验作业，确保入库（出厂）产品可焊性质量，包括满足无铅焊锡焊接条件。）62Range (范围)It is adequste for all the soldering product of the ccompany. (适用于本公司所有产品的可焊接性试验作业。)63Stadard of the employment (引用标准)Q/SMC-001-2000, Standard for the corporation producing Solar Cell of dm light and amophous silicon。(Q/SMC-001-2000, 弱光性非晶硅太阳能电池产品企业标准。)64Definition (定义)SolderingThe ability and intensity of the soldering between the lead-free tin and the products copper under the rating condition. (可焊性产品电极材料（铜浆）的焊接强度、能力)65Condition of soldering ecperiment (可焊接性试验条件)651Soder: It is fit for the lead-free tin and other rosin tin. (焊接材料：无铅焊锡或含松香的其它焊锡丝)652Soldering temperture: 260330. (焊接温度：260330.)653Soldering length should be less than 3 secinds. (焊接时间：3秒钟。)654Condition of Iron: The same temperatiure and pow should be less than 30W. (烙铁要求：恒温、功率30W。)655Soldering time: Repeat that not more than twice. (焊接次数：重复不得超过2次)66Standard for regular soldering ecperiment for one piece of the product. (可焊性试验合格片标准)661Soldering dot must be or of und and it must cover more than 2/3 of each copper. （焊点光滑圆润，焊点面积占铜浆2/3以上为合格片。）662Tensile test: Pulling must be more than 0.5 Kg (拉力测试：拉力0.5Kg)67Standard for regular soldering ecperiment for each group of the product. (可焊性试验产品合格批标准。)671Operative frequency: Batch. (实施频度：每批。)672Probaive method: Sample and visualzation. (检验方法：抽样、目测。)673Sample number: 10pcs. (抽样样本数：10pcs.)674Do the soldering and pulling experiment to 6.5.1 and 6.5.2。（按6.5.1和6.5.2步骤进行焊接和拉力试验。675T