IEC EN60065 测试表格.doc

2编号: NMC-415Rev: A/1Laboratory Measurements NS Technology Co., Ltd.Project EngineerClient Lab EngineerApplianceRequested DateModel No.Re-testStandardIEC 60065:2001/EN 60065:2002/UL/C 60065:2003 GB8898Full-test (LVD)Report No.NSS-ModificationConstruction checkAdd Test after reviewLab Measurements return to Engineer directly (If no tick, put into default tray)Lab Use OnlyLab Start Date / /2008Lab Finish Date/ /2008Remarks:This lab measurement report is for general office equipment. Unless otherwise specified, all values mentioned in this lab report are in r.m.s. value.Summary of Testing:*Clause(s)Test(s)ResultRemark5Durability of Marking TestP / F5.1Input Current TestP / F6.1Ionizing radiationSub-contracted6.2Laser radiationSub-contracted7 Heating under Normal OperationsP / F7.2Softening Test for insulation materialSub-contractedIf current 0,2A8.3Humidity Test for hygroscopic MaterialsP / F8.1320N test for windows, lenses, etc.P / F8.1450N test for coversP / FTouch current and PE currentP / F9.1.6Discharge Test of Mains PlugP / F9.1.7Resistance to external Forces (50N or 250N)P / F10.1Surge TestP / F10.2Humidity TestP / F10.3Insulation Resistance and electric StrengthP / F11.1Touch current under Fault ConditionsP / F11.2Heating under Fault ConditionsP / F12.1.1Bump TestP / F12.1.2Vibration TestSub-contracted12.1.3Impact TestP / F12.1.4Drop TestP / F12.1.5Stress Relief TestP / F12.2Fixing of actuating ElementsP / F12.3Remote control devicesP / F12.4DrawersP / F12.5Antenna coaxial SocketsP / F12.6.1Physical Securement of AntennaP / F13.2Working VoltagesP / F15.2Ground Continuity TestP / F15.4Devices forming a part of the Mains Plug Torque TestP / F15.4.3Mains Plug Drop and Pin TestP / F16.5Non-detachable Flexible CordsP / F17.1Screw TerminalsP / F17.7 Cover fixing DevicesP / F18Mechanical Strength of Picture TubesSub-contracted19.1Tilting Test (10)P / F19.2/19.3Cart StabilityP / F19.5.1Fragmentation testSub-contracted19.6Wall or ceiling mounting meansP / F Additional test for non-approved components according to 8.18, 13.6, 13.7 or 14P / F Select the test(s) to be done.Remark: Please submit the test plan together with the tables for clause 7, 7.2, 11 andAttachments:Ambient Temperature, oC25Relative Humidity, %50Barometric Pressure, mBar1013Date Signature Test EngineerDate Signature Checked byDate Signature Approved by3编号: NMC-415Rev: A/1Test equipment list as attached. (pls. tick used equipment for testing)TEST SAMPLE IDENTIFICATION:The table below is provided to provide correlation of sample numbers to specific product related information. Refer to this table when a test identifies a test sample by Sample No. only.Sample Card No.(S（year）（MONTH）-（Sample No.）)Date Received (dd/mm/yy)Manufacturer, Product Identification and RatingsS601001-17编号: NMC-415Rev: A/15Durability of MARKINGCurling? Yes / NoLegibility? Yes / NoP / FSample # :5.1/7.1TABLE: temperature rise measurementsP / FPower consumption in the OFF/Stand-byPosition of the functional switch (W):Operating conditionsUn (V)In (A)Pn (W)Pout (W)Loudspeaker impedance ():Several loudspeaker systemsMarking of loudspeaker terminalsMonitored point:Test voltageTest voltageLimit dT (K)dT (K)dT (K)Winding temperature rise measurementsAmbient temperature t1 (oC):Ambient temperature t2 (oC):Temperature rise dT of winding:R1 ()R2 ()dT (K)Limit dT (K)Insulation classNote: Input current test shall be done at Rated Voltage/RangeHeating test shall be done at +-10%. The resistance method is optional.Sample # :8.3Insulation of hazardous live parts not provided by hygroscopic material 40C, 90-95% R.H. for 96h 40C, 90-95% R.H. for 168h (tropical)Pass electrical Strength?Yes / NoP / FSample # :8.13Adequate fastening of windows, lenses, lamp covers etc. (pull test 20N for 10s)Location:P / F8.14Adequate fastening of covers (pull test 50N for 10s)Location:P / FSample # :Touch current measured from terminal devices using the network in annexD:U1:(peak for a.c.)U2: (peak for a.c.)Location:Earth leakage current:P / FDischarge not exceeding 45CP / FEnergy of discharge not exceeding 350mJP / FSample # :9.1.6No shock hazard due to stored charge on withdrawal of the mains plug; voltage (V) after 2s:P / FIf C is not greater than 0,1F no test neededP / F9.1.7Enclosure sufficiently resistant to external forceP / FTest probe11 of IEC 61032 for 10s (50N)Location:P / FTest hook of fig.4 for 10s (20N)Location:P / F30mm diameter test tool for 5s (100 or 250N):Location:P / FSample # :10.1Surge test10kV, 50 times, 12/minPass insulation resistance?Yes / NoP / FSample # :10.2Humidity conditioning 30C, 91-95% R.H. for 48h 40C at 93% R.H. for 120h (tropical)Pass electrical Strength?Yes / NoP / FSample # :10.3TABLE: insulation resistance measurementsP / FInsulation resistance R between:R (M)Required R (M)Between mains poles (primary fuse disconnected)2Between parts separated by basic or supplementary insulation2Between parts separated by double or reinforced insulation4Sample # :10.3TABLE: electric strength measurementsP / FTest voltage applied between:Test voltage (V rms)BreakdownMains poles (primary fuse disconnected)1500Between parts separated by basic or supplementary insulation1500Between parts separated by double or reinforced insulation3000Sample # :11.1No shock hazard under fault conditionU1: (peak for a.c.)U2: (peak for a.c.)Location:P / FSample # :11.2TABLE: summary of fault condition testsP / FVoltage (V) 0,9 or 1,1times rated voltage:Ambient temperature (oC):Monitored point:Under fault conditions specified:dT (K)Limit dT (K)Winding temperature rise measurementsAmbient temperature t1 (oC):Ambient temperature t2 (oC):Note: Tested under the worst condition of the heating test results in table 7.Sample # :12