PKS配置冗余服务器.doc

Note1:In this version, if you want to use the NIC on main board and a single identical NIC, please use the manual.Note2:Everyone must be obey the rules of anti viruses and manages our files and programs.PKS Installation1. Install the Win2k server: a.Please check your computer name (XXA,XXB).b.Be sure Video display:1024x768 pixels.c.Be sure your redundant server administrator password is identical.d.Install Win2K sp4 Patche. Installing the PCIC driversPrerequisites Experion PKS R201 Applications Software CD.To install the PCIC drivers:Step Action1 Insert the Experion PKS R201 Applications Software CD into the CD-ROMdrive.2 In the Computer Management dialog box, right-click in the pane displaying thedevices, and then click Scan for Hardware Changes.3 Click Other Device and then click Reinstall Driver.4 Click Next to start installing the driver.5 Click Display a list of the known drivers for this device so that I canchoose a specific driver and then click Next.6 Click Other Device.7 Click Have Disk to display the Install from Disk dialog box.8 Click Browse and then browse to the following folder on the CD:RSLinxRSLinxpnp_DriversWin2k1784-PCIC(S)9 Click OK.10 Click A-B 1784-PCIC(S).11 Click Next.12 Click Yes in the update driver warning message dialog box.13 Click Next.14 If a confirm file replace message dialog box is displayed, click Yes to continuethe installation.15 Click Finish to complete the installation.f.Verifying the PCIC driverTo verify if the PCIC driver is installed:Step Action1 On the Windows Desktop, right-click on the My Computer icon and chooseManage.2 Click the Device Manager item.3 If the A-B Virtual Backplane item does not exist, Install the PCIC drivers onpage 430.4 In the Computer Management dialog box, expand the A-B Virtual Backplaneitem.5 Double-click the A-B 1784-PCIC(S) item to display the Properties dialog box.6 Click the Driver tab and then click Driver Details.7 Click the ABPCICSW.sys file in the Driver files list.8 Review the file version displayed below the Driver files list.9 The file version must be 3.6.18 WDM. If it is not, you need to update the PCICdriver: continue to 431.10 Click the VirtualBackplane.sys file in the Driver files list.11 Review the file version displayed below the Driver files list.12 The file version must be 1.9. If it is not, you need to update the PCIC driver:continue to 431.13 If both of driver files are the correct versions, click OK to close the Driver FileDetails dialog box, the click OK to close the Properties dialog box, and thenclose the Computer Management dialog box.2. IP settings (refer to the network design)3. Installation of PKS:with administrator logon, first insert the Base CD, then begin.! Be careful of remembering that our User name: mngr; password :mngr12! Remember to restart the computer after complete PKS installation!4. Patch installation:4.1. Install Experion PKS patch 7.4.2. Install System Management and FTE components.4.3. Installing Experion PKS Patch 84.4. Installing Experion PKS Patch 94.5. Installing Fault Tolerance Ethernet (FTE) Patch R201.1.1.24.6. Installing the System Management Patch R20111.1.14.7. NO4.8. Installing Experion PKS Patch 124.9. Installing Experion PKS Patch 134.10. Installing Experion PKS Patch 144.11. Installing Experion PKS Patch 154.12. Installing Experion PKS Patch 164.13. Installing Experion PKS Patch 174.14. Installing Experion PKS Patch 184.15. Configure Server Redundancy & Synchronize 4.1 Steps to install patch7 in redundant servers:StepActionRepeat the following steps on both server A and server B:At ServerB only:1.Run the DB Admin application at Start Programs Experion PKSEngineer Tools2.In the right pane, click Disable Replication icon and then click Yes when prompted Are you sure you want to disable database replication? Repeat the following steps on both server A and server B:3.Stop the server and unload the database 4.In the patch installation, click the setup.exe.5.You can verify that the patch was installed by opening the following file: C:Program FilesHoneywellExperion PKSEngineering Tools ProductVersion.txtIf the line R201.0 Patch 07 installed (R201.0.08.7) is present, patch 07 was successfully installed.Start the PKS server to “System Running” status At ServerB only6.Run the DB Admin, in the right pane, click Enable Replication icon and then click Yes when prompted Are you sure you want to Enable database replication?At both ServerA and ServerB7 Start the server into running.4.2 To complete the mandatory preparation at ServerA & ServerBTo remove Honeywell_HCI_Runtime and Honeywell Packaged Redistributable Files if exist.StepAction1.Stop the server and unload the database:Mode 2.Insert the Experion PKS R201 Support Software CD into the CD-ROM. In Windows Explorer, browse to the Utilities folder on the CD and then double-click the hprf.reg file. 3.Choose Start Settings Control Panel and double-click the Add/Remove Programs icon. Click Honeywell_HCI_Runtime or HCI_Runtime and then click Remove. Click Yes to confirm removal Click Honeywell Packaged Redistributable Files and then click Remove. Click Yes to confirm removal.4.Shutdown and restart the computer. Installing Honeywell System Management DisplayInsert the Experion PKS Common Components CD into the CD-ROM drive. It will auto run.Install the Honeywell Packaged Redistributable Files from the Platform menu from the Common Components screen. Then rebootInsert the Experion PKS Common Components CD into the CD-ROM drive. It will auto run and select Licensed Package Installer from the Common Components CD.Review the information about installing software, license agreements, and third-party compatibility on the next several screens. Click Next to continue.Enter license and authorization number as shown in the below of EPKS Server License Certificate. Click Next to continue.Select Honeywell System Management Display and click Install Package button.After a successful installation, click Exit and OK to end the Installation process.Manually reboot your computer.Install and Configure of FTE Node Components:(i) Configure the connection speed for NIC card (FTE node ports)1.Right-click My Network Places and select Properties.2.The status should now be as shown Network and Connections dialog Right-click the local area connection and rename it to “FTEA” Right-click the local area connection #2 Network and rename it to “FTEB”3.Right-click the FTEA and select Properties4.From the Properties page, select Configure and click the Advanced tab.5.In the Property list, select the Link Speed & Duplex and set to 100Mbps/ Full Duplex.6.Click OK to apply the changes.7.Select Internet Protocol (TCP/IP) from the FTEA Properties page and click Properties.8.From the Internet Protocol (TCP/IP) Properties page, enter your IP address (eg.10.38.1.31) and Subnet mask (eg.255.255.255.0) and click Advanced the button. 9From the Advanced TCP/IP Settings page, IP Setting tab, enter 1 for Interface metric. 10.Click the DNS tab, select Register this connections addresses in DNS a shown below. 11.Click the WINS tab, select Enable NetBIOS over TCP/IP and then click OK. 12.Click OK to close the Internet Protocol (TCP/IP) Properties page.13.Click OK to close FTEA Properties page.14.Right-click the FTEB and select Properties15.From the Properties page, select Configure and click the Advanced tab.16.In the Property list, select the Link Speed & Duplex and set to 100Mbps/ Full Duplex.17.Click OK to apply the changes.18.Select Internet Protocol (TCP/IP) from the FTEB Properties page and click Properties.19.From the Internet Protocol (TCP/IP) Properties page, enter your IP address (eg.10.38.1.32) and Subnet mask (eg.255.255.255.0) and click Advanced the button. 20.From the Advanced TCP/IP Settings page, IP Setting Tab, enter 5 for Interface metric. 21.Click the DNS tab, de-select Register this connections addresses in DNS a shown below. 22.Click the WINS tab, select Disable NetBIOS over TCP/IP and then click OK. 23.Click OK to close the Internet Protocol (TCP/IP) Properties page.24.Click OK to close FTEB Properties page.25.Close the Network and Dial-up Connections windows. Reboot the computer.(ii) Arrange Adapters Binding order1.Right-click My Network Places and select Properties.2.At the Network and Dial-up connections, click at Advanced pull-down menu and select Advanced Setting.3.At the Adapters and Bindings Tab, make sure that FTEA appears first in binding order (upper row) than FTEB.Example: Note:If the network adapter port you connected to Switch A is NOT listed first, reorder the connections using the arrows.4.Click Ok to save if changes are made else click Cancel close the windows.5.Open the Command Prompt by StartRun and type cmd and click OK6.At the command Prompt, type:ipconfig/all If you use two single NIC, you should choose small physical address as FTEA.Example:Ethernet adapter FTEA: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel Pro/100S Dual Port Server Adapter Physical Address. . . . . . . . . : 44-45-53-54-42-00 DHCP Enabled. . . . . . . . . . : No IP Address. . . . . . . . . . . . .: 10.38.1.31 Subnet Mask . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . : DNS Servers . . . . . . . . . . . :Ethernet adapter FTEB: Media State . . . . . . . . . . . : Cable Disconnected Description . . . . . . . . . . . : Int Intel Pro/100S Dual Port Server Adapter #2 Physical Address. . . . . . . . : 44-E5-53-54-42-00 DHCP Enabled. . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.38.1.32 Subnet Mask . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . : DNS Servers . . . . . . . . . . :Note: FTEA should display first then follows by FTEB Adapter.7.Reboot the computer.(v) Install FTE S/W:Stop services and processes( the following1-4 can be ignored if it is your first time to install FTE.1.Click Start, point to Settings, and then click Control Panel.2.Double-click Administrative Tools, and then double-click Component Services.3.In the console Tree, select Services and click the Name column to sort the services and locate Windows Management Instrumentation Service4.Right-click and select Stop. Together, itll also stop few of system Management (sm xxxx) services.Stop the remaining of System Management Services (sm-xxxx).Open the Windows Task Manager (right-click at Task Bar) and select the Process tab.If theses Processes exist, stop it:cas.exe hsopcserv.exe hscsysmg.exe5Stop Experion PKS Server by click StartPrograms Experion PKS Server and then Start-Stop Experion PKS Server.6Insert the Common Components CD into the CD-ROM drive, it will auto launch or double-clicking Install from the Package folder. 7Select the appropriate package from the Install screen and click Next.8Review the Honeywell Software Installation Welcome screen and click Next. 9.Review the Honeywell Software Installation End User License Agreement screen and click Next. 10Review the Honeywell Software Installation Third Party Software Compatibility Policy screen and click Next.11Complete the Honeywell Software Installation User Information screen and click Next.12.Select Fault Tolerant Ethernet Driver (FTE) and click Install Package.13.From the Honeywell Software Installation Installable Packages screen and accept the selected defaults. Click OK.14.When prompted “Do you want to run the FTE Driver Install Script (ftecfg) now?” click NO.After successfully completed installation, if prompted to reboot, click No.15.Click Exit from the Installation window and do a manual reboot.4.34.4 Installing Experion PKS Patch 8、9Can refer to the Install patch7 in redundant servers in 5.1 step.4.5 Installing Fault Tolerance Ethernet (FTE) Patch FTE_201.1.2Installing the FTE Patch FTE_201.1.2StepAction1.Create a temporary folder c:Program FilesHoneywellFTE_DriverSaved2.i)Move the old fteimdrv.sys file located in c:Program FilesHoneywellFTE_Driver to c:Program FilesHoneywellFTE_DriverSavedii)Copy the fteimdrv.sys file from FTE_201.1.2 patch to c:Program FilesHoneywellFTE_Driver3.Verify the new fteimdrv.sys file which have been updated.Right-click fteimdrv.sys, and select the “Properties”. Click the “Version” tab of the Properties dialog, which should indicate a file version of 201.1.7.400. 4.Install the FTE Service. i) From the Network Connections dialog, right-click either one of FTE Network Connections being used for FTE, and then click Properties.ii) Click Install from the Local Area Connection Properties page and select Service, and then click Add.iii) Click Have Disk to access the FTE intermediate driver files that loaded on the hard drive earlierNote: FTE was previously installed, it will appear in the Network Service list. DO NOT pick it from the list.iv) Browse to the location of the FTE intermediate driver files and click Open.Default is C:Program FilesHoneywellFTE_Driverv) Click OK and select Honeywell Fault Tolerant Ethernet Service then click OK.vi) If your digital signature protection level is set to Warn, the Digital Signature Not Found message will appear. Click Yes for each message box that appears to continue the installation. vii) The Honeywell Fault Tolerant Ethernet Service should now appear in the Local Area Connection Properties dialog.viii) Click Close to return to Network Connections.10.Reboot the computer11.From the Network Connections dialog, right-click either one of FTE Network Connections being used for FTE, and then click Properties.12.Select Honeywell Fault Tolerant Ethernet Service then click Properties. This opens the Honeywell Fault Tolerant Ethernet Service Properties dialog.13.From the FTE Configuration tab, select both of the adapters that are being used for FTE. 10114.Enter a Device Index value that is greater than 0 and equal to or less than the Max FTE Nodes settingExample: Note:Device Index Must Be Unique throughout the whole FTE network. For the other Client machines, use the FTE status display to check for free Device Index.15.Click OK to save the setting and close the Network Adapter connection Properties.16.Reboot the computer.4.6 Installing the System Management Patch R2011.1.1StepAction1.Pls refer to the file “system_mgmt_2011.1.1.patch.pdf”4.7NO 4.84.14 Installing Experion PKS Patch 1218Can refer to the Install patch7 in redundant servers in 4.1 step.4.15 Configure Server Redundancy & Synchronizea.Modify the host fileremember to update the PKS host file in such content, you only need to fill in the smaller IP in odd. eg,127.0.0.1localhost200.0.0.1serveraservera0200.0.0.3serverbserverb0b.Confiure Server redundant On the serveraFirstly, click Start - Programs - Honeywell Experion PKS Server - Start-Stop Experion PKS Server. Left click icon in top left of title bar and select Advanced - Full Mode. Select Database Only and Yes. i)Open the Command Prompt by StartRun and type cmd and click OK.ii) At the command Prompt, type:cd program fileshoneywellexperion pksserveruser c:program fileshoneywellexperion pksserveruserhdwbld redun.hdwrestart the PKS server.On the serverbFirstly, click Start - Programs - Honeywell Experion PKS Server - Start-Stop Experion PKS Server. Left click icon in top left of title bar and select Advanced - Full Mode. Select Database Only and Yes. i)Open the Command Prompt by StartRun and type cmd and click OK.ii) At the command Prompt, type:cd program fileshoneywellexperion pksserveruser c:program fileshoneywellexper