华为配置命令.doc

交换机命令Quidwaydis cur ；显示当前配置Quidwaydisplay current-configuration ；显示当前配置Quidwaydisplay interfaces ；显示接口信息Quidwaydisplay vlan all ；显示路由信息Quidwaydisplay version ；显示版本信息Quidwaysuper password ；修改特权用户密码Quidwaysysname ；交换机命名Quidwayinterface ethernet 0/1 ；进入接口视图Quidwayinterface vlan x ；进入接口视图Quidway-Vlan-interfacexip address ；配置VLAN的IP地址Quidwayip route-static ；静态路由网关Quidwayrip ；三层交换支持Quidwaylocal-user ftpQuidwayuser-interface vty 0 4 ；进入虚拟终端S3026-ui-vty0-4authentication-mode password ；设置口令模式S3026-ui-vty0-4set authentication-mode password simple 222 ；设置口令S3026-ui-vty0-4user privilege level 3 ；用户级别Quidwayinterface ethernet 0/1 ；进入端口模式Quidwayint e0/1 ；进入端口模式Quidway-Ethernet0/1duplex half|full|auto ；配置端口工作状态Quidway-Ethernet0/1speed 10|100|auto ；配置端口工作速率Quidway-Ethernet0/1flow-control ；配置端口流控Quidway-Ethernet0/1mdi across|auto|normal ；配置端口平接扭接Quidway-Ethernet0/1port link-type trunk|access|hybrid ；设置端口工作模式Quidway-Ethernet0/1port access vlan 3 ；当前端口加入到VLANQuidway-Ethernet0/2port trunk permit vlan ID|All ；设trunk允许的VLANQuidway-Ethernet0/3port trunk pvid vlan 3 ；设置trunk端口的PVIDQuidway-Ethernet0/1undo shutdown ；激活端口Quidway-Ethernet0/1shutdown ；关闭端口Quidway-Ethernet0/1quit ；返回Quidwayvlan 3 ；创建VLANQuidway-vlan3port ethernet 0/1 ；在VLAN中增加端口Quidway-vlan3port e0/1 ；简写方式Quidway-vlan3port ethernet 0/1 to ethernet 0/4 ；在VLAN中增加端口Quidway-vlan3port e0/1 to e0/4 ；简写方式#interface Vlanif41 ip address 2 #interface Ethernet0/0/1 broadcast-suppression 10 port link-type access port default vlan 1755 loopback-detect enable loopback-detect action block ntdp enable ndp enableQuidwaymonitor-port ；指定镜像端口Quidwayport mirror ；指定被镜像端口Quidwayport mirror int_list observing-port int_type int_num ；指定镜像和被镜像Quidwaydescription string ；指定VLAN描述字符Quidwaydescription ；删除VLAN描述字符Quidwaydisplay vlan vlan_id ；查看VLAN设置Quidwaystp enable|disable ；设置生成树,默认关闭Quidwaystp priority 4096 ；设置交换机的优先级Quidwaystp root primary|secondary ；设置为根或根的备份Quidway-Ethernet0/1stp cost 200 ；设置交换机端口的花费Quidwaylink-aggregation e0/1 to e0/4 ingress|both ; 端口的聚合Quidwayundo link-aggregation e0/1|all ; 始端口为通道号SwitchA-vlanxisolate-user-vlan enable ；设置主vlanSwitchAisolate-user-vlan secondary ；设置主vlan包括的子vlanQuidway-Ethernet0/2port hybrid pvid vlan ；设置vlan的pvidQuidway-Ethernet0/2port hybrid pvid ；删除vlan的pvidQuidway-Ethernet0/2port hybrid vlan vlan_id_list untagged ；设置无标识的vlan如果包的vlan id与PVId一致，则去掉vlan信息. 默认PVID=1。所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged.路由器命令Quidwaydisplay version ；显示版本信息Quidwaydisplay current-configuration ；显示当前配置Quidwaydisplay interfaces ；显示接口信息Quidwaydisplay ip route ；显示路由信息Quidwaysysname aabbcc ；更改主机名Quidwaysuper passwrod 123456 ；设置口令Quidwayinterface serial0 ；进入接口Quidway-serial0ip address ；配置端口IP地址Quidway-serial0undo shutdown ；激活端口Quidwaylink-protocol hdlc ；绑定hdlc协议Quidwayuser-interface vty 0 4Quidway-ui-vty0-4authentication-mode passwordQuidway-ui-vty0-4set authentication-mode password simple 222Quidway-ui-vty0-4user privilege level 3Quidway-ui-vty0-4quitQuidwaydebugging hdlc all serial0 ；显示所有信息Quidwaydebugging hdlc event serial0 ；调试事件信息Quidwaydebugging hdlc packet serial0 ；显示包的信息静态路由：Quidwayip route-static interface number|nexthopvaluereject|blackhole例如：Quidwayip route-static 16 Quidwayip route-static Quidwayip route-static 16 Serial 2Quidwayip route-static 动态路由：Quidwayrip ；设置动态路由Quidwayrip work ；设置工作允许Quidwayrip input ；设置入口允许Quidwayrip output ；设置出口允许Quidway-ripnetwork ；设置交换路由网络Quidway-ripnetwork all ；设置与所有网络交换Quidway-rippeer ip-address ；Quidway-ripsummary ；路由聚合Quidwayrip version 1 ；设置工作在版本1Quidwayrip version 2 multicast