Windows Perl Module installation.doc

Windows Active Perl 模块安装说明一、 软件需求远程服务器启动SNMP服务，假设IP地址10.8.8.125，通信串为“public”Perl程序：ActivePerl-5.10.1.1006-MSWin32-x86-291086.msiGcc程序：devcpp-4.9.9.2_setup.rardmake程序：dmake-4.12-20090907-SHAY.zipPerl模块源码程序：Net-SNMP-v6.0.1.tar.gz二、 安装步骤1. 安装devcpp程序一路默认安装，安装目录c:devcpp设置系统环境变量，在 path变量添加“c:devcppbin”打开命令行，输入 “gcc -v”，如果输出正常表示环境变量设置正确。2. 安装dmake程序解压dmake 放到C:目录下设置系统path环境变量路径，添加路径c:dmake，确保dmake程序在此目录下。命令行运行 “dmake v” ，测试环境变量设置是否正确。3. 安装Perl模块解压Net-SNMP-v6.0.1.tar.gz源码压缩包，得到目录Net-SNMP-v6.0.1，目录更名为Net-SNMP并复制到C:根目录命令行进入C:Net-SNMP目录，输入以下命令：C:Net-SNMPperl Makefile.PLSet up gcc environment - 3.4.2 (mingw-special)Checking if your kit is complete.Looks goodWarning: prerequisite Crypt:DES 2.03 not found.Writing Makefile for Net:SNMPC:Net-SNMPdmakedmake: Warning: - Target blibdirs was made but the time stamp has not been updated.cp lib/Net/SNMP/Security/USM.pm bliblibNetSNMPSecurityUSM.pmcp lib/Net/SNMP/Dispatcher.pm bliblibNetSNMPDispatcher.pmcp lib/Net/SNMP/Transport/IPv6.pm bliblibNetSNMPTransportIPv6.pmcp lib/Net/SNMP/Transport/IPv4/UDP.pm bliblibNetSNMPTransportIPv4UDP.pmcp lib/Net/SNMP.pm bliblibNetSNMP.pmcp lib/Net/SNMP/MessageProcessing.pm bliblibNetSNMPMessageProcessing.pmcp lib/Net/SNMP/Security/Community.pm bliblibNetSNMPSecurityCommunity.pmcp lib/Net/SNMP/Message.pm bliblibNetSNMPMessage.pmcp lib/Net/SNMP/Transport.pm bliblibNetSNMPTransport.pmcp lib/Net/SNMP/PDU.pm bliblibNetSNMPPDU.pmcp lib/Net/SNMP/Security.pm bliblibNetSNMPSecurity.pmcp lib/Net/SNMP/Transport/IPv6/UDP.pm bliblibNetSNMPTransportIPv6UDP.pmcp lib/Net/SNMP/Transport/IPv4.pm bliblibNetSNMPTransportIPv4.pmcp lib/Net/SNMP/Transport/IPv6/TCP.pm bliblibNetSNMPTransportIPv6TCP.pmcp lib/Net/SNMP/Transport/IPv4/TCP.pm bliblibNetSNMPTransportIPv4TCP.pmC:Perlbinperl.exe -Iblibarch -Ibliblib snmpkey.PL snmpkeyC:Perlbinperl.exe -MExtUtils:Command -e cp - snmpkey blibscriptsnmpkeypl2bat.bat blibscriptsnmpkeydmake: Warning: - Target pure_all was made but the time stamp has not been updated.C:Net-SNMPdmake testC:Perlbinperl.exe -MExtUtils:Command:MM -e test_harness(0, bliblib, blibarch) t/*.tt/ber.t . okt/dsp.t . okt/mp.t . okt/usm.t . okAll tests successful.Files=4, Tests=43, 7 wallclock secs ( 0.03 usr + 0.16 sys = 0.19 CPU)Result: PASSC:Net-SNMPdmake installInstalling C:PerlhtmlsitelibNetSNMP.htmlInstalling C:Perlhtmlbinsnmpkey.htmlInstalling C:PerlsitelibNetSNMP.pmInstalling C:PerlsitelibNetSNMPDispatcher.pmInstalling C:PerlsitelibNetSNMPMessageProcessing.pmInstalling C:PerlsitelibNetSNMPMessage.pmInstalling C:PerlsitelibNetSNMPTransport.pmInstalling C:PerlsitelibNetSNMPPDU.pmInstalling C:PerlsitelibNetSNMPSecurity.pmInstalling C:PerlsitelibNetSNMPSecurityUSM.pmInstalling C:PerlsitelibNetSNMPSecurityCommunity.pmInstalling C:PerlsitelibNetSNMPTransportIPv6.pmInstalling C:PerlsitelibNetSNMPTransportIPv4.pmInstalling C:PerlsitelibNetSNMPTransportIPv4UDP.pmInstalling C:PerlsitelibNetSNMPTransportIPv4TCP.pmInstalling C:PerlsitelibNetSNMPTransportIPv6UDP.pmInstalling C:PerlsitelibNetSNMPTransportIPv6TCP.pmInstalling C:PerlsitebinsnmpkeyInstalling C:Perlsitebinsnmpkey.batAppending installation info to C:Perllib/perllocal.podC:Net-SNMPcd .4. 测试模块是否安装成功1) 登陆Perl Packet Manag