发动机词汇.doc_第1页
发动机词汇.doc_第2页
发动机词汇.doc_第3页
发动机词汇.doc_第4页
发动机词汇.doc_第5页
已阅读5页,还剩6页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

气缸体总成 cylinder block assembly 齿轮室部件 timing gear chamber subassembly 气缸盖及气缸盖罩 cylinder head & its cowl hood 活塞及连杆 piston & connecting rod 曲轴减振器总成 crankshaft damper assembly 凸轮轴总成 camshaft assembly 配气机构 valve train 进气管部件 air intake manifold subassembly 排气管组件 exhaust manifold subassembly 油底壳总成 oil sump assembly 机油集滤器 oil strainer 机油泵 oil pump 机油滤清器 oil filter 机油冷却器总成 oil cooler assembly 曲轴箱通风装置 crankcase ventilator 供油系管路总成 fuel supply system pipeline assembly 燃油滤清器总成 fuel filter assembly 喷油泵总成 fuel injection pump assembly 喷油器部件 fuel injector assembly 燃油喷射泵附件总成 fuel injection pump fittings assembly 断油机构总成 fuel cut-off mechanism 增压器总成 turbocharger assembly 放水开关 water drain cock 节温器总成 thermostat assembly 水泵总成 water pump assembly 动力输出总成 power take-off mechanism assembly 转向泵总成 steering pump assembly 气制动空气压缩机 air compressor for pneumatic braking 发电机总成 alternator assembly 起动机 starter 仪表、感应器总成 meters & sensors assembly 定位套 locating collar 气缸体 cylinder block 气缸套 cylinder liner 螺塞 plug screw 碗形塞片 bowl-shaped tabular plug 主油道螺塞 plug screw for main oil gallery 凸轮轴衬套 camshaft bushing I 凸轮轴端盖 camshaft end cover 曲轴后油封 crankshaft rear oil seal 定位销 locating pin 垫圈 washer 螺栓 bolt 曲轴后油封座 crankshaft rear oil seal seat 后油封座垫片 rear oil seal seat gasket 主轴承盖(后) main bearing cap (rear) 主轴承盖螺栓 main bearing cap bolt 螺塞 plug screw 止推主轴承盖 thrust main bearing cap 油标尺座孔堵塞 dipstick seat hole stop 碗形塞片 bowl-shaped tabular plug 喷嘴组件 injector component 主轴承盖 main bearing cap 定位销 locating pin 惰齿轮衬套 idler gear bush 惰轮轴螺栓 idler gear bolt 惰齿轮轴 idler gear shaft 惰齿轮 idler gear 惰齿轮防磨板 idler gear wear plate 碗形塞片 bowl-shaped tabular plug 凸轮轴衬套 camshaft bushing 发动机分类 往复式内燃机 reciprocating internal combustion engine 化油器式发动机 carburetor engine 转子发动机 rotary engine 旋轮线转子发动机 rotary trochoidal engine 二冲程发动机 two-stroke engine 四冲程发动机 four-stroke engine 增压式发动机 supercharged engine 风冷式发动机 air-cooled engine 油冷式发动机 oil-cooled engine 水冷式发动机 water-cooled engine 自然进气式发动机 naturally aspirated engine 煤气机 gas engine 液化石油气发动机 liquified petroleum gas engine 柴油煤气机 diesel gas engine 多种燃料发动机 multi-fuel engine 碳氢化合物发动机 hydrocarbon engine 双燃料发动机 duel fuel engine 热球式发动机 hot bulb engine 多气缸发动机 multiple cylinder engine 对置活塞发动机 opposed piston engine 对置气缸式发动机 opposed-cylinder engine 十字头型发动机 cross head engine 直列式发动机 in-line engine 星型发动机 radial engine 筒状活塞发动机 trunk-piston engine 斯特林发动机 stirling engine 套阀式发动机 knight engine 气孔扫气式发动机 port-scavenged engine 倾斜式发动机 slant engine 前置式发动机 front-engine 后置式发动机 rear-engine 中置式发动机 central engine 左侧发动机 left-hand engine 右侧发动机 right-hand engine 短冲程发动机 oversquare engine 长冲程发动机 undersquare engine 等径程发动机 square engine 顶置凸轮轴发动机 overhead camshaft engine 双顶置凸轮轴发动机 dual overhead camshaft engine V形发动机 V-engine 顶置气门发动机 valve in-head engine 侧置气门发动机 side valve engine 无气门发动机 valveless engine 多气门发动机 multi-valve engine 卧式发动机 horizontal engine 斜置式发动机 inclined engine 立式发动机 vertical engine W形发动机 w-engine I形发动机 I-engine L形发动机 L-engine F形发动机 F-engine 原机 Engine prototype 发动机性能 二冲程循环 two-stroke cycle 四冲程循环 four-stroke cycle 狄塞尔循环 diesel cycle 奥托循环 otto cycle 混合循环 mixed cycle 定容循环 constant volume cycle 工作循环 working cycle 等压循环 constant pressure cycle 理想循环 ideal cycle 热力循环 thermodynamic cycle 冲程 stroke 活塞行程 piston stroke 长行程 long stroke 上行程 up stroke 下行程 down stroke 进气行程 intake stroke 充气行程 charging stroke 压缩行程 compression stroke 爆炸行程 explosion stroke 膨胀行程 expansion stroke 动力行程 power stroke 排气行程 exhaust stroke 膨胀换气行程 expansion-exchange stroke 换气压缩行程 exchange-compression stroke 上止点 top dead center(upper dead center) 下止点 lower dead center(bottom dead center) 上止点前 budc(before upper dead center) 上止点后 atdc(after top dead center) 下止点前 bbdc(before bottom dead center) 下止点后 abdc(after bottom dead center) 排气量 displacement 发动机排量 engine displacement 活塞排量 piston swept volume 气缸容量 cylinder capacity 单室容量 single-chamber capacity 容积法 volumetry 压缩比 compression ratio 临界压缩比 critical compression ratio 膨胀比 expansion ratio 面容比 surface to volume ratio 行程缸径比 stroke-bore ratio 混合比 mixture ratio 压缩压力 compression pressure 制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio 燃空比 fuel air ratio 燃料当量比 fuel equivalence ratio 扭矩 torque 单缸功 power per cylinder 升功率 power per liter 升扭矩 torque per liter 升质量 mass per liter 减额功率 derating power 输出马力 shaft horsepower 马力小时,马力时 horsepower-hour 总马力 gross horse power 总功率 gross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consumption 空气消耗率 air consumption 机油消耗量 oil consumption 有效马力 net horse power 额定马力 rated horse power 马力重量系数 horsepower-weight factor 制动功率 brake horse power 制动热效率 brake thermal efficiency 总效率 overall efficiency 排烟极限功率 smoke limiting horsepower 功率曲线 power curve 机械损失 mechanical loss 机械效率 mechanical efficiency 有效热效率 effective thermal efficiency 充气系数 volumetric efficiency 过量空气系数 coefficient of excess air 适应性系数 adaptive coefficient 扭矩适应性系数 coefficient of torque adaptability 转速适应性系数 speed adaptive coefficient 强化系数 coefficient of intensification 校正系数 correction factor 换算系数 conversion factor 活塞平均速度 mean piston speed 发动机转速 engine speed (rotational frequency) 充量(进气) charge 旋转方向 direction of rotation 顺时针 clockwise 逆时针 counter-clockwise 左转 left-hand rotation 右转 right-hand rotation 发动机性能 engine performance 加载性能 loading performance 起动性能 starting performance 加速性能 acceleration performance 动力性能 power performance 排放性能 emission performance 燃油经济性 Fuel economy 排放 Exhaust emissions 大的燃烧噪声 Large combustion noise 预混合燃烧 Premixed combustion 扩散燃烧 Diffusion combustion 大的EGR率 Heavy EGR 推迟喷油时间 Retarding the injection timing 推迟喷油时间 Delaying the fuel injection timing 燃烧激振力 Combustion excitation forces (CPL) CO2排放 Carbon dioxide (CO2) emissions 温室气体 Greenhouse gas 热效率 Thermal efficiency 辅助涡流室 Auxiliary swirl chamber 黑烟 Black smoke Nox氮氧化物 Nitrogen oxides PM颗粒物 Particulate matter EGR废气再循环 Exhaust gas recirculation 燃油供给系统 The fuel injection system 在低负荷区 In the low load region 气缸压力 The cylinder pressure level 曲轴转角 The crank angle 1/3倍频程 1/3 octave band of the frequency 全负荷 Full load 部分负荷 Partial load 声压级 Sound pressure level 发动机扭矩 Engine torque 燃烧噪声 Combustion noise 机械噪声 Mechanical noise 涡轮增压的 Turbocharged 涡轮增压器 Turbocharger 着火燃迟期 The ignition delay period 喷油泵 The fuel injection pump 增压中冷柴油机 Intercooled turbocharged diesel 碳化氢 Hydrocarbon (HC) 进气管几何尺寸 Intake port geometry 水平轴 Horizontal axis 声功率 Sound power level 竖直轴 Vertical axis 辐射噪声 Radiation noise 发动机测功机 engine dynamometer 零负荷到中等负荷 Idling to a medium-load 振幅 Amplitude 气缸体振动 Cylinder block vibration 声压级 Sound pressure level 随着曲轴转角 In relation to the crank angle 最大汽缸压力 The maximum cylinder pressure 最大汽缸压力升高率 The cylinder pressure gradient 共轨系统 Common-rail system 可变喷嘴涡轮增压器 variable nozzle turbocharger 引导喷射 pilot injection 4气门DOHC系统 4-valve DOHC system 计算机辅助工程CAE computer-aided engineering 固有噪声 Born noise 侧面挠度 lateral bending 排气岐管 exhaust manifold 进气岐管 intake manifold 交流发电机 alternator 齿轮箱 gear case 供油泵 supply pump 起动机 starter 共振频率 resonance frequency 气缸压力快速升高率 the rapid rising rate of cylinder pressure主喷量和主喷时间 main injection volume, timing 共轨油压 fuel pressure in a common-rail 放热率 heat release ratio 步进电机 step-motor 频谱图 frequency spectrum map 油膜 oil film 机械噪声 mechanical noise 识别 identify 变量 variable 隔离声音的传播途径 Isolate sound transmission routes 衰减 Attenuation 半消声室 Semi-anechoic chamber 系数 Coefficient 正时带 Timing belt 台架实验 Bench test 气门驱动凸轮 Valve-drive cam 传递系数 Transfer coefficient 矢量 vector 气穴现象 Cavitation 微处理器 microprocessor 执行器 actuator 电控泵 electronically controlled pump 构造 气缸盖 cylinder head 气缸体 cylinder block 整体铸造 inblock cast (enblock cast ) 发动机罩 engine bonnet 气缸体加强筋 engine block stiffening rib 气缸 cylinder 示功图 indicator chart/diagram 缸体(转子机) stator 缸径 cylinder bore 气缸体机架 cylinder block frame 配气机构箱 valve mechanism casing 气缸体隔片 cylinder spacer 气缸盖密封环 cylinder head ring gasket 气缸盖垫片 cylinder head gasket 气缸套 cylinder liner(cylinder sleeve) 干式缸套 dry cylinder liner 湿式缸套 wet cylinder liner 气缸水套 water jacket 膨胀塞 expansion plug 防冻塞 freeze plug 气缸壁 cylinder wall 环脊 ring ridge 排气口 exhaust port 中间隔板 intermediate diaphragm导板 guideway 创成半径(转子机) generating radius 缸体宽度(转子机) operating width 燃烧室 combustion bowl 浅盆形缩口燃烧室 shallow reentrant combustion chamber 主燃烧室 main combustion chamber 副燃烧室 subsidiary combustion chamber 预燃室 prechamber 涡流燃烧室 swirl combustion chamber 分开式燃烧室 divided combustion chamber 涡流式燃烧室 turbulence combustion chamber 半球形燃烧室 hemispherical combustion chamber 浴盆形燃烧室 bathtub section combustion chamber L 形燃烧室 L-combustion chamber 楔形燃烧室 wedge-section combustion chamber 开式燃烧室 open combustion chamber 封闭喷射室 closed spray chamber 活塞顶内燃烧室 piston chamber 爆发室 explosion chamber 燃烧室容积比 volume ratio of combustion chamber 发动机托架 engine holding frame engine 动力机装置 power unit 直喷柴油机 DI (direct-injection) diesel engine 非直喷柴油机 IDI (Indirect-injection)diesel engine 动力传动系 power train 连杆 connecting rod 油底壳 oil pan 活塞销 piston pin 气缸套 cylinder bore 凸轮齿 cam gear 空气室 energy chamber 气缸余隙容积 cylinder clearance volume 燃烧室容积 combustion chamber volume 气缸最大容积 maximum cylinder volume 压缩室 compression chamber 外径 major diameter 中径 pitch diameter 内径 minor diameter 径向间隙 radial clearance 两极调速器 limiting speed governor 特性 空转特性 no load characteristics 负荷特性 part throttle characteristics (汽油机) load characteristics 调速特性 governor control characteristics 万有特性 mapping characteristics 稳定调速率 steady state speed governing rate 工况 怠速转速 idling speed 经济转速 economic speed 起动转速 starting speed 最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque 最高空转转速 maximum no load governed speed 调速 speed governing 超速 over-speed 怠速 idling 转速波动率 speed fluctuation rate 工况 working condition(operating mode) 额定工况 declared working condition 变工况 variable working condition 稳定工况 steady working condition 空载 no-load 全负荷 full load 超负荷 overload 部分负荷 part load 怠速控制 idling-speed control 怠速工况 idling condition 起动工况 starting condition 起动转速 cranking speed 急减速工况 abrupt decreasing condition 加速工况 accelerating condition 驻车 park 调速 Speed governing 应急跛行模式 limp-in mode 排放 欧洲排放标准 Emission Standards in the EU燃油质量 Fuel Quality 生产一致性检测 Conformity of Production (COP) 燃油消耗 Fuel Consumption排放检测 Exhaust Emission Measurement 排气管 tailpipe 一氧化碳 Carbon monoxide 曲轴箱燃油蒸发排放量 emissions of crankcase gases耐久性试验 Ageing test 欧洲的排放、燃油及发 EPEFE = European Program on Emssions, Fuels and Engine Technologies 动机技术项目 燃油质量 fuel properties汽车制造商 Car Manufacturers 排放对空气质量的影响Impact of vehicle emissions on air quality 十六烷值 Cetane number 蒸发特性 Evaporation characteristic 无硫燃油 Sulfur-free Fuels 测试循环 Testcycle 新的欧洲标准测试循环 NEDC = New European Dri

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论