ABBETL500载波机点位说明.doc_第1页
ABBETL500载波机点位说明.doc_第2页
ABBETL500载波机点位说明.doc_第3页
全文预览已结束

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

ABB ETL500载波机点位说明一、遥信遥信点位遥信文本1未知硬件告警(HW)Hardware alarm2音频发送信号峰值越限(HW)(HW)AF Tx signal is exceeding peak amplitude3丢失假负载或P4LS(HW)(HW)Missing RF hybrid, dummy load or P4LS478/ P7LC丢失P4LR(HW)(HW) Missing P4LR on position 78/P7LC5从板硬件告警(HW)(HW) HW alarm on slave board6G4AK modem告警(HW)(HW) Alarm from a G4AK modem7P4LQ上DSPA主记数器告警(HW)(HW) DSPA main counter alarm on P4LQ8P4LQ上DSPA发送记数器告警(HW)(HW) DSPA Tx counter alarm on P4LQ9P4LQ上DSPA接收记数器告警(HW)(HW) DSPA Rx counter alarm on P4LQ10P4LQ上DSPC主记数器告警(HW)(HW) DSPC main counter alarm on P4LQ11均衡器数据错误(HW)(HW) Equalizer data corrupt12UART不工作(HW)(HW) UART not working13TDM总线通信错误(HW)(HW) TDM bus communication error14Set RTC date(HW)(HW) Set RTC date15载频输出电平低(HW)(HW) Low RF output level16G4AK modem告警(HW)(HW) Alarm from a G4AK modem17P4LQ上DSP B数据内存错误(HW)(HW) error during data memory access of DSPB on P4LQ18P4LQ上DSP A程序内存错误(HW)(HW) Program memory error DSP A on P4LQ19P4LQ上DSP B程序内存错误(HW)(HW) Program memory error DSP B on P4LQ20P4LQ上DSP C程序内存错误(HW)(HW) Program memory error DSP C on P4LQ21NSD550硬件告警(HW)(HW) HW alarm on NSD55022IRIG信号丢失(HW)(HW) IRIG signal lost23RTC date错误(HW)(HW) Incorrect RTC date24-12V欠压(HW)(HW) -12V undervoltage25-12V过压(HW)(HW) -12V overvoltage26+12V欠压(HW)(HW) +12V undervoltage27+12V过压(HW)(HW) +12V overvoltage28P4LQ上Flash读写出错(HW)(HW) Flash EPROM read/write error on P4LQ29P4LQ上Flash出错(HW)(HW) Flash EPROM error on P4LQ30NSD550上电路告警(Link)(Link) Link alarm on NSD55031同步丢失(Link)(Link) Synchronisation lost32通道1信噪比告警(Link)(Link) SNR alarm on channel 133通道1无接收导频(Link)(Link) No Rx Pilot on channel 134通道1接收导频电平告警(Link)(Link) Rx Pilot level alarm on channel 135通道1AGC控制闭锁(Link)(Link) AGC blocked on channel 136通道2信噪比告警(Link)(Link) SNR alarm on channel 237通道2无接收导频(Link)(Link) No Rx pilot on channel 238通道2接收导频电平告警(Link)(Link) Rx pilot level alarm on channel 239通道2AGC控制闭锁(Link)(Link) AGC blocked on channel 240未知电路告警或警告信号(HW)未知电路告警或警告信号4180W功放警告(警告)(Warning) Warning from the 80W amplifier42从板警告(警告)(Warning) Warning on slave board43NSD550警告(警告)(Warning) Warning on NSD55044测试PLC-link switches未设置(警告)(Warning) Test PLC-link switches not set to default45设备处于非正常状态(警告)(Warning) Equipment not in noarmal operation mode46EOC Ch1通信失败(警告)(Warning) EOC Ch1 communication failure47Ch1无EOC接收数据(警告)(Warning) EOC no data received on Ch148当前均衡器与测试结果不一致(警告)(Warning) Actual equalizer not consistent with new measurement Not allowed to store the configuration to EPROM49与远端设备固件不匹配(警告)(Warning) Inconsist firmware on local and remote equipment50Ch1无EOC发送数据(警告)(Warning) EOC no data send on Ch151Ch2无EOC发送数据(警告)(Warning) EOC no data send on Ch252Ch2无EOC接收数据(警告)(Warning) EOC no data received on Ch253EOC ch2通信失败(警告)(Warning) EOC Ch2 communication failure54测试配置状态(警告)(Warning) Test configuration active55均衡器动作未决(警告)(Warning) Equalizer action pending56插入假负载/(警告)(Warning)Dummy load plugged / RF loopback active Equalizer switched off57未知NSD550告警(NSD550)(NSD550) 未知NSD550告警58TDM总线通信故障(NSD550)(NSD550) TDM bus communication error59信噪比告警(NSD550)(NSD550) SNR alarm60接收电平告警(NSD550)(NSD550) Rx level alarm61环回测试失败(NSD550)(NSD550) Cyclic loop test failed more than 2 times62事件记录器故障(NSD550)(NSD550) Eventrecorder disabled63Guard and trip present(NSD550)(NSD550) Guard and trip present64G4AI硬件告警(NSD550)(NSD550) Hardware alarm on G4AI65自定义命令表校验错(NSD550)(NSD550) Custom command table checksum alarm66测试信号激活(NSD550)(NSD550) NSD550 testsignal active (Warning)67一次环回测试失败(NSD550)(NSD550) cyclic looptest failed once (Warning)68环回测试超出范围(NSD550)(NSD550) cyclic looptest out of range (Warning)69本地环回激活(NSD550)(NSD550) local loop active (Warning)70事件记录器(NSD550)(NSD550) Info: Eventrecorder changing block71N11通信错误(Slot)(Slot) Error communicating with slot N1172N11主板警告(Slot)(Slot) Warning on board at slot N1173N11主板错误(Slot)(Slot) Error on board at slot N1174N22通信错误(Slot)(Slot) Error communicating with slot N2275N22主板警告(Slot)(Slot) Warning on board at slot N2276N22主板错误(Slot)(Slot) Error on board at slot N2277N28通信错误(Slot)(Slot) Error communicating with slot N2878N28主板警告(Slot)(Slot) Warning on board at slot N2879N28主板错误(Slot)(Slot) Error on board at slot N2880N34通信错误(Slot)(Slot) Error communicating with slot N3481N34主板警告(Slot)(Slot) Warning on board at slot N3482N34主板错误(Slot)(Slot) Error on board at slot N3483N54通信错误(Slot)(Slot) Error communicating with slot N5484N54主板警告(Slot)(Slot) Warning on board at slot N5485N54主板错误(Slot)(Slot) Error on board at slot N5486N65通信错误(Slot)(Slot) Error communicating with slot N6587N65主板警告(Slot)(Slot) Warning on board at slot N6588N65主板错误(Slot)(Slot) Error on board at slot N6589N71通信错误(Slot)(Slot) Error communicating with slot N7190N71主板警告(Slot)(Slot) Warning on board at slot N7191N71主板错误(Slot)(Slot) Error on board at slot N7192N00通信错误(Slot)(Slot) Error

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论