FSX键盘命令.docVIP

动 作指 令暂停PauseP or BREAK（BREAK）全屏模式Full Screen ModeALT + ENTER（回车键）菜单显示/隐藏Menus (display/hide)ALTATC菜单显示/隐藏ATC Menu (display/hide)ACCENT（重点符号）or SCROLL LOCK（SCROLL LOCK键）膝板显示/隐藏Kneeboard (display/hide)SHIFT+F10声音开/关Sound (on/off)Q重置当前飞行Reset Current FlightCTRL+; (分号)保存飞行Save Flight; (分号)退出飞行模拟Exit Flight SimulatorCTRL+C立即退出飞行模拟Exit Flight Simulator ImmediatelyCTRL+BREAK（BREAK键）摇杆（禁用/使用）Joystick (on/off)CTRL+K全球坐标/帧频Cycle Coordinates/Frame RateSHIFT+Z选择第一个Select Item 11选择第二个Select Item 22选择第三个Select Item 33选择第四个Select Item 44选择时间压缩Select Time CompressionR空投物资Drop ObjectsSHIFT+D请求加油车Fuel Truck (request)SHIFT+F航空器标签显示/隐藏Aircraft Labels (display/hide)CTRL+SHIFT+L飞行技巧显示/隐藏Flying Tips (display/hide)CTRL+SHIFT+X增大选择Increase Selection= (等号)缓慢增大选择Increase Selection SlightlySHIFT+= (等号)缓慢减小选择Decrease Selection SlightlySHIFT+- (减号)减小选择Decrease Selection- (减号)捕获截图Capture ScreenshotV登机桥廊对接/分离Jetway (attach/detach)CTRL+J结束飞行End FlightESC飞机控制面指令（CONTROL SURFACE COMMANDS）动 作指 令副翼左倾斜Ailerons (bank left)数字键盘4副翼右倾斜Ailerons (bank right)数字键盘6副翼左配平Aileron Trim (left)CTRL+数字键盘4副翼右配平Aileron Trim (right)CTRL+数字键盘6垂直尾翼 左偏航Rudder (yaw left)数字键盘0垂直尾翼 右偏航Rudder (yaw right)数字键盘ENTER（回车键）垂直尾翼 左配平Rudder Trim (left)CTRL+数字键盘0垂直尾翼 右配平Rudder Trim (right)CTRL+数字键盘ENTER（回车键）副翼或垂直尾翼居中Center Ailerons and Rudder数字键盘5水平升降舵向下Pitch Down (elevator)数字键盘8水平升降舵向上Pitch Up (elevator)数字键盘2升降舵 向下配平Elevator Trim Down数字键盘7升降舵 向上配平Elevator Trim Up数字键盘1襟翼完全收起Flaps (retract fully)F5襟翼缓慢收起Flaps (retract incrementally)F6襟翼缓慢伸出Flaps (extend incrementally)F7襟翼完全伸出Flaps (extend fully)F8扰流板/减速板开/关Extend/Retract Spoilers/Airbrakes/ (正斜线)扰流板预位Arm SpoilersSHIFT+/ (正斜线)水舵收/放Water Rudder Up/DownCTRL+W发动机控制指令（ENGINE COMMANDS）动 作指 令对于多引擎飞机上，除非你先按下E+引擎号(1-4)选择单个引擎，否则你的操作将对所有引擎生效。要恢复对所有引擎的控制，先按住E，然后快速连续地按下所有引擎号(E, 1, 2,等等)On multiengine aircraft, engine commands affect all engines unless you first select an engine.选择引擎Select EngineE+引擎编号(1-4)选择所有引擎Select All EnginesE+1+2+3+4自动启动引擎Engine AutostartCTRL+E切断节流阀(节流阀就是油门)Throttle (cut)F1反冲力(涡扇发动机/喷气发动机)Reverse Thrust (turboprops/jets)F2 (按住且保持)降低节流阀Throttle (decrease)F2 or数字键盘3增加节流阀Throttle (increase)F3 or数字键盘9节流阀最大Throttle (full)F4螺旋桨低转速Propeller (low RPM)CTRL+F1降低螺旋桨转速Propeller (decrease RPM)CTRL+F2增大螺旋桨转速Propeller (increase RPM)CTRL+F3螺旋桨高转速Propeller (high RPM)CTRL+F4油气混合比设置为慢车低油状态Mixture (idle cutoff)CTRL+SHIFT+F1减小油气混合比Mixture (lean quickly)CTRL+SHIFT+F2增大油气混合比Mixture (enrich)CTRL+SHIFT+F3油气混合比设置为高油量状态Mixture (full rich)CTRL+SHIFT+F4引擎除冰开/关Carb Heat/Engine Anti-ice (on/off)H磁电机选择Magnetos (select)M选择主用电池组或者交流发电机Master Battery/Alternator (select)SHIFT+M选择喷气发动机启动器Jet Starter (select)J直升机旋翼离合器开/关Helicopter Rotor Clutch (on/off)SHIFT+. (句点)直升机旋翼调节器开/关Helicopter Rotor Governor (on/off)SHIFT+, (逗点)直升机旋翼制动器开/关Helicopter Rotor Brake (on/off)SHIFT+B增加选择项目Increase Selection= (等号)逐渐增加选择项目Increase Selection SlightlySHIFT+= (等号)逐渐减小选择项目Decrease Selection SlightlySHIFT+- (减号)减小选择项目Decrease Selection- (减号)通用飞机控制指令（GENERAL AIRCRAFT COMMANDS）动 作指 令锁定/释放停机刹车Brake (set parking)CTRL+. (句点)后推开始/停止Pushback (start/stop)SHIFT+P(再按1或2使尾部向右或者向左)使用/释放刹车Brakes (apply/release). (句点)使用左刹车Brakes (apply left brake)数字键盘+ (加号)使用右刹车Brakes (apply right brake)数字键盘- (减号)收/放起落架Landing Gear (extend/retract)G尾轮锁定开/关Tail wheel (lock/unlock)SHIFT+G手动放下起落架（若系统失效）Landing Gear (extend manually)CTRL+G燃料供应开/关Fuel Dump (on/off)CTRL+SHIFT+D子面板显示或隐藏Subpanels (display/hide)SHIFT + 1到9烟雾系统开/关Smoke System (on/off)I整流罩（通风片）（逐渐）开启Cowl Flaps (open incrementally)CTRL+SHIFT+V整流罩（通风片）（逐渐）关闭Cowl Flaps (close incrementally)CTRL+SHIFT+C请求牵引飞机Tow Plane (call)CTRL+SHIFT+Y释放牵引绳索Tow Rope (release)SHIFT+Y舱门选择Doors (select)SHIFT+E（再按1-4以开启/关闭）灯光指令（LIGHT COMMANDS）动 作指 令全部灯开/关Lights - all (on/off)L机外闪光警示灯开/关Strobe Lights (on/off)O面板灯开/关Panel Lights (on/off)SHIFT+L降落灯开/关Landing Lights (on/off)CTRL+L降落灯（下斜）Landing Light (tilt down)CTRL+SHIFT+数字键盘2降落灯（左斜）Landing Light (tilt left)CTRL+SHIFT+数字键盘4降落灯（右斜）Landing Light (tilt right)CTRL+SHIFT+数字键盘6降落灯（上斜）Landing Light (tilt up)CTRL+SHIFT+数字键盘8降落灯（归正）Landing Light (center)CTRL+SHIFT+数字键盘5无线电指令（RADIO COMMANDS）动 作指 令ATC窗口（显示/隐藏）ATC Window (display/hide)重点符or SCROLL LOCK（SCROLL LOCK键）VOR 1识别开/关VOR 1 Ident (on/off)CTRL+1VOR 1识别开/关(on/off)CTRL+2MKR识别开/关MKR Ident (on/off)CTRL+3DME识别开/关DME Ident (on/off)CTRL+4ADF识别开/关ADF Ident (on/off)CTRL+5备用频率切换Standby Frequency (swap)XCOM无线电选择COM Radio (select)CNAV无线电选择NAV Radio (select)NOBS指示器选择OBS indicator (select)SHIFT+VADF选择ADF (select)CTRL+SHIFT+ADME选择DME (select)F雷达收发器选择Transponder (select)T增加选择项目Increase Selection= (等号)逐渐增加选择项目Increase Selection SlightlySHIFT+= (等号)逐渐减少选择项目Decrease Selection SlightlySHIFT+- (减号)减少选择项目Decrease Selection- (减号)自动驾驶指令（AUTOPILOT COMMANDS）动 作指 令自动驾驶主开/关Master (on/off)Z自动驾驶飞行导向仪开/关Flight Director (on/off)CTRL+F自动驾驶机翼水平调整器开/关Wing Leveler (on/off)CTRL+V自动驾驶偏航阻尼器开/关Yaw Damper (on/off)CTRL+D自动驾驶高度保持开/关Altitude Hold (on/off)CTRL+ Z自动驾驶高度选择Altitude Bug (select)CTRL+SHIFT+Z自动驾驶航向保持开/关Heading Hold (on/off)CTRL+H自动驾驶航向选择Heading Bug (select)CTRL+SHIFT+H自动驾驶空速保持开关Airspeed Hold (on/off)CTRL+R自动驾驶马赫数保持开/关Mach Hold (on/off)CTRL+M自动驾驶空速保持开/关Autothrottle (arm)SHIFT+R自动驾驶自动油门起飞/重飞(TOGA)模式Autothrottle engage (TOGA)CTRL+SHIFT+G自动驾驶NAV1保持开/关Nav 1 Hold (on/off)CTRL+N自动驾驶近进模式开/关Approach Mode (on/off)CTRL+A自动驾驶回航模式开/关Back Course Mode (on/off)CTRL+B自动驾驶左右定位维持开/关Localizer Hold (on/off)CTRL+O自动驾驶姿态保持开/关Attitude Hold (on/off)CTRL+T增加选择项目Increase Selection= (等号)逐渐增加选择项目Increase Selection SlightlySHIFT+= (等号)逐渐减少选择项目Decrease Selection SlightlySHIFT+- (减号)减少选择项目Decrease Selection- (减号)仪器仪表指令（INSTRUMENT COMMANDS）动 作指 令航向指示仪 复位Heading Indicator (reset)D高度计复位Altimeter (reset)B皮托管加热开/关Pitot Heat (on/off)SHIFT+H增加选择项目Increase Selection= (等号)逐渐增加选择项目Increase Selection SlightlySHIFT+= (等号)逐渐减少选择项目Decrease Selection SlightlySHIFT+- (减号)减少选择项目Decrease Selection- (减号)视野指令（VIEW COMMANDS）动 作指 令2维驾驶舱（面板、着路面板、仪表、窗外）循环转换2-D Cockpit (cycle panels)W切换至面板视野Snap to Panel ViewSHIFT+数字键盘0转换视野(面板,虚拟驾驶舱,塔台,现场)View (next category)S反向转换视野View (previous category)SHIFT+S转换座舱视角View (next view in category)A反向转换座舱视角View (previous view in category)SHIFT+A查看前一视角View (previous view toggle)CTRL+S恢复至默认缩放比例1倍View (default zoom)BACKSPACE（退格键）看Look (snap)Num Pad（数字键盘）看Look (pan)Hat switch（摇杆控制帽i）or thumbstick（按钮开关）恢复至向前看Look (reset to forward view)SHIFT+数字键盘DEL鼠标指示开Look Using Mouse (on)Hold SPACEBAR（按住空格键）鼠标指示开/关Look Using Mouse (on/off)SHIFT+O打开新视野窗口View (open new window) (左括弧)关闭视野窗口View (close selected window) (右括弧)打开新的俯视视野窗口View (open new top-down window)SHIFT+ (右括弧)切换到虚拟驾驶舱Virtual CockpitF9切换到2D驾驶舱2-D CockpitF10切换到追踪视野Locked Spot ViewF11切换到俯视视野Top-Down ViewF12二维面板透明度（加或减）2-D Panel TransparencyCTRL+SHIFT+T (+ or -)将选择的窗口放在最上层Window (bring selected to front) (撇号)放大Zoom In= (等号)缩小Zoom Out- (减号)切换到下个视野View (next window)CTRL+TAB切换到上个视野View (previous window)CTRL+SHIFT+TAB视点后移Eyepoint (move back)CTRL+ENTER（回车键）视点下移(座椅降低)Eyepoint (move down)SHIFT+BACKSPACE（退格键）视点前移Eyepoint (move forward)CTRL+BACKSPACE（退格键）视点左移Eyepoint (move left)CTRL+SHIFT+BACKSPACE（退格键）视点右移Eyepoint (move right)CTRL+SHIFT+ENTER（回车键）视点上移(座椅升高)Eyepoint (move up)SHIFT+ENTER（回车键）恢复视野Eyepoint (reset)CTRL+SPACE（空格键）移位指令（SLEW COMMANDS）动 作指 令移位请您不用真正的飞行，即可快速地将飞机移到新的位置。请用以下指令进行移位。Slew to rapidly reposition your aircraft without flying in real time.移位模式开/关Slew Mode (on/off)Y设定为朝北航向/平直飞行姿态Heading North/Attitude LevelCTRL+SPACEBAR（空格键）冻结所有移动Freeze All Movement数字键盘5前移Slew Forward数字键盘8后移Slew Backward数字键盘2左移Slew Left数字键盘4右移Slew Right数字键盘6慢速增加高度Slew Up SlowlyQ or F3快速增加高度Slew Up Qui