Time relay instruction.doc

无锡意凯自动化技术有限公司Wuxi YK automation technology Co., Ltd YJDS1- series Time relay instructionINSTRUCTION无锡意凯自动化技术有限公司Wuxi YK Automation Technology Co., Ltd地址：江苏省无锡市锡山区胶阳路2855号ADD: No.2855.JIAOYANG ROAD, ANZHEN, XISHAN DISTRICT, WUXI, JIANGSU, CHINA电话（TEL）真（FAX）编（POST Code）:214105YJDS1- series Time relay instructionOperation:1. code set: the old key is “05-1”When power on, press the for 8 seconds, it will get into the code setting state. At this time the first two positions will be flashing. Pressing () to change the data to get the function you want. The function of each code is as below:codeRange Mark Code Range Mark 010.01sec.99.99sec.Plus timing single relay1099hour and 59min1minMinus timing single relay0299.99sec.0.01sec.Minus timing single relay111min99hour and 59minPlus timing double relay031min.9999min.Plus timing single relay1299hour and 59min1 minMinus timing double relay049999min1minMinus timing single relay131 sec.99min and 59sec.Plus timing double relay051sec.9999sec.Plus timing single relay1499min and 59 sec.1 sec.Minus timing double relay069999sec.1sec.Minus timing single relay151 sec.9999sec.Plus timing double relay071sec.99min. and 59sec.Plus timing single relay169999sec.1 secMinus timing double relay0899min and 59 sec.1 sec.Minus timing single relay171 min9999minPlus timing double relay091 min99hour and 59minPlus timing single relay189999min1 minMinus timing double relay2. operating instruction for single setting time relay(4 numbers):(1) Display: when working normally, the up 4 LED showing the delay data, the bottom 4 LED showing the set data.(2) Choosing key: when setting, it is used for choose the one which will be set. The chose one will be flashing.(3) Increasing key ():when setting, after press , press this key can change the data which is flashing.(4) Reset key : when working normally, press this key, the time delayer will recover to old state. Loose the reset key, the time delayer will start to delay.(5) Pause key : when working normally, press this key , delay stops; loose this key, time delay is continue. Use this function, it can be used as a cumulative time meter.(6) Setting of delaying data: use Increasing key and Choosing key can set any delaying data in the showing range. Press the choosing key for first time, the POW indicator will be light, the first position at bottom will be flashing, press the () , set the 1st data, then press to next , the 2nd position will be flashing, press the () to set second data. And so on, can set the 3rd., and 4th . At this time, it still be flashing, after 8 seconds, flashing will stop. The set data will be record automatically.Use reset key or power again both can make the time delayer start to delay. After finish delay, the relay will work according to its working way.(7) set the relay working way: there are 6 kinds of output wayAt the same time of setting code, press choosing key to make the up 4 data flashing, then use the () to change the relays working way:A: when set the number after code”_”(namely the 4th data) as “1”,it means the up motor working, get or over the set data, relay is close.B: when set the number after code”_”(namely the 4th data) as “1”,it means the up motor isnt working(it can make the motor working by reset key or reset terminal)get or over the set data, relay is close.C: when set the number after code”_”(namely the 4th data) as “3”,it means the up motor working, get or over the set data, relay is loose.D: when set the number after code”_”(namely the 4th data) as “4”,it means the up motor isnt working(it can make the motor working by reset key or reset terminal)get or over the set data, relay is loose.E: when set the number after code”_”(namely the 4th data) as “5”,it means the up motor working, get or over the set data, relay is close. After 5 seconds, system will be reset automatically.F: when set the number after code”_”(namely the 4th data) as “6”,it means the up motor isnt working(it can make the motor working by reset key or reset terminal)get or over the set data, relay is close. After 5 seconds, system will be reset automatically.3. Operating instruction for double setting time relay(4 numbers): Display: when working normally, the up 4 LED showing the current value of loose and close time .The bottom 4 LED showing the set data of relay. When setting, the up 4 LED showing the set value of relay loose time, The bottom 4 LED showing the set value of relay close . Choosing key: when setting, it is used for choose the one which will be set. The chose one will be flashing.3 Increasing key ():when setting, after press , press this key can change the data which is flashing. When working normally, press this key , the display will show the set value of relay loose and close.4 Reset key : when working normally, press this key, the time delayer will recover to old state. Loose the reset key, the time delayer will start to delay.Pause key : when working normally, press this key , delay stops; loose this key, time delay is continue. set the time of loose and close: use Increasing key and Choosing key can set the time of relay loose or close in the range of showing. Press the firstly, the up 1 st. position will flash, press () set this value, then press choosing key , the 2nd. Position will flash, press () to set this value and so on. After set the 4th., position, press , the down 1st., position will flash, press () to set this value, then press to next position to set value and so on. After set the four values, it set the close time well. At this time, it still flash, after 8 seconds, it will stop automatically. The data you set will be record into the meter automatically. Use reset key or power again both can make the time delayer start to delay from the relay loose time. (At this time, the POW indicator still flash, the OUT indicator will be light). After the delay, the relay will close, then the relay will work circularly according to the set data. Note: during the setting process, you should set continually, the interval between every two steps shouldnt over 8 seconds.7 Set the relay working way: there are 2 kinds of output wayAt the time of setting code, press choosing key to make the up 4th., position flash, then use the increasing key() to change the out way of relay:A: when set the number after code”_”(namely the 4th data) as “1”,it means the up motor working, get or over the set data, relay is close.B: when set the number after code”_”(namely the 4th data) as “1”,it means the up motor isnt working(it can make the motor working by reset key or reset terminal)get or over the set data, relay is close.4. product introduction and wiring diagram:the terminal introduction of single setting relay :A: the terminal of relay contactor: means always close,means always open.B: COM is public terminal, PAU is pause terminal, RST is reset terminal.C: when normal working, connect the COM public terminal and PAU pause terminal, delay is stop. Loose them, delay will be continue.