10HG工业型组合逆流式冷却塔.doc

10HG工业型组合逆流式冷却塔.地址：常州市常澄路1号 邮 编： 213002 电话：传真：冷却塔选用说明选塔参数1、工艺要求循环水量Q（m3/h）进水温度t1（）出水温度t2（）进水浊度噪音要求进水PH值2、气象参数空气干球温度（）空气湿球温度t（）大气压力Pa（Pa）空气相对湿度夏季最高气温冬季最低气温选塔要求1、塔形：根据用途、场地有限制、环境协调、投资及用户经验确定。2、颜色：一般情况 下，我们产品采用色彩清新自然的果色。用户也可以根据自己需要，选用与环境协其它颜色。3、塔距：圆塔多塔设计，塔与塔之间净距离应保持不小于0.5倍塔体直径。横流塔及方塔可并列布置。4、冷却塔应尽量避免布置在热源、废气和烟气发生点、化学品堆放处和煤堆附近。5、冷却塔之间或塔与其它建筑物之间的距离，除了考虑塔的通风要求，塔与建筑物相互影响外，还应考虑建筑物防火、防爆的安全距离及冷却塔的施工及检修要求。6、选用水泵应与冷却塔配套，保证流量，扬程满足工艺要求，旋转布水器或配水槽需要自由水头为1米，管式喷咀为4米。设计条件干球温度=31.5湿球温度r=28大气压P=1.004105Pa进水温度t1=42出水温度t2=32设计说明1、本基础图为三台拼装图，如台数有变更，则由需方按实际情况自定。2、各基础标高在同一水平上，标高误差2mm，各中心距偏差3mm。3、水池深度、进水方式、出水管大小及位置、排污、放空等均由用户按实际情况自定。技术参数塔型标准循环水量M3/h单格外形尺寸通风机装置配水系统重量标准点噪音dB(A)长Lmm宽Dmm高Hmm风量104M3/h直径mm电机功率KW进水管dgmm进水支管nDg2干重b湿重t10HG-50050092806815850048.0400030350415018.926.87510HG-600600104807815850053500030400415022.834.37510HG-750750105608215937566.0500037450415026.541.27510HG-100010001200094151002084.0600045500415032.651.37510HG-15001500130401161510030119.0700075600415046.181.67510HG-20002000149201241512450143.0800090700415049.995.37510HG-25002500162001351513280167.08530110800415056.6100.37510HG-30003000166001471513780192.08530132900415069.8117.57510HG-35003500170001561514280216.08530160900415080.3134.07510HG-40004000184001741514280248.091401851000415091.7151.27510HG-45004500184001922514280278.0914022010004150105.4170.47510HG工业型组合横流式冷却塔各部尺寸塔型各部尺寸mmB0B1B2B3H0L0L1L2L3L4L510HG-5001560050001250300580085001800245010800334060010HG-6001860060001500300580097001900295012000362590010HG-75019800640016003006300972019002960120204185120010HG-1000234007600190030068001108020003540133804065150010HG-1500300009800245030073001206022003830143604220200010HG-2000324001060026503008450137825004390160804730200010HG-25003570011700195030089501498028004690172804890150010HG-30003930012900215030094501532030004660176205390160010HG-35004200013800230030099501564032004620179405890180010HG-4000474001560019503009950170403200532019340519015001