稳压电源 代码.docx

#include#include#define uint unsigned int#define uchar unsigned char uchar code table=0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77;uchar data tab2;uchar ws2=0,0;uchar code table2=0xbf,0x86,0xdb,0xcf,0xe6,0xed,0xfd,0x87,0xff,0xef,0xf7;uchar code tablewei=0x0e,0x0d;sbit dula=P15;sbit dawr=P26;/DA写数据段 sbit dacs=P27;/DA始能段uchar num1,f,f1,f2,f3,f4,f5,f6,keynum;/f为数字键标志位;f1为DA转换标志位;f2,f4分别为+,-0.1标志位;f3为清零标志位 void delay(uint z)/延时子程序uint x,y;for(x=z;x0;x-)for(y=110;y0;y-);void display(uint number)/显示LED uchar i,j; tab0=number%10; tab1=number/10; for(i=0,j=0;i2;i+,j+) dula=1; P2=tableweij; if(i=0) P0=tabletabi; else P0=table2tabi; dula=0; delay(5); keyscan()/键盘扫描 uchar num,tt; P1=0xfe; tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 delay(50); tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 tt=P1; switch(tt) case 0xee: num=7,f=1; break; case 0xde: num=8;f=1; break; case 0xbe: num=9;f=1; break; case 0x7e: num=0;f3=1;/清零按键 break; default:break; while(tt!=0xf0) tt=P1; tt=tt&0xf0; P1=0xfd; tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 delay(50); tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 tt=P1; switch(tt) case 0xed: num=4;f=1; break; case 0xdd: num=5;f=1; break; case 0xbd: num=6;f=1; break; case 0x7d: num=14;f4=1;/减0.1按键 break; default:break; while(tt!=0xf0) tt=P1; tt=tt&0xf0; P1=0xfb; tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 delay(50); tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 tt=P1; switch(tt) case 0xeb: num=1;f=1; break; case 0xdb: num=2;f=1; break; case 0xbb: num=3;f=1; break; case 0x7b: num=+;f2=1;/加0.1按键 break; default:break; while(tt!=0xf0) tt=P1; tt=tt&0xf0; P1=0xf7; tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 delay(50); tt=P1; tt=tt&0xf0; while(tt!=0xf0) / 检查按键是否被摁下 tt=P1; switch(tt) case 0xe7: num=0;f=1; break; case 0xd7: num=10;f1=1;/确认DA转换按键 break; case 0xb7: num=11;f5=1; break; case 0x77: num=12;f6=1; break; default:break; while(tt!=0xf0) tt=P1; tt=tt&0xf0; return(num);void jishu()/预置电压值 keynum=keyscan(); if(f=1) f=0; num1=num1*10+keynum; void change()/DA转换 if(f1=1) P3=(uchar)(256*num1/100); delay(100); void up_down_clear()/加减0.1和清零 if(f2=1) f2=0; num1+; if(f4=1) f4=0; num1-; if(f3=1) f3=0; num1=0; void up_down_1()/加减1 if(f5=1) f5=0; num1=num1+10; if(f6=1) f6=0; num1=