试谈B级产品(含B+)外观检验标准.doc

1.0 目的： 规范A级产品（含出口CD-ROM）光碟外观检验标准，确保成品符合产品质量要求。2.0 适用范围：本公司生产的所有光碟产品之生产及检验各环节。3.0 检验环境及人员要求：3.1 温湿度：按生产车间环境要求。（252，70以下）3.2 检验人员要求：无色盲、色弱，经上岗考核合格；3.3 亮度：在一般日光灯照明下，避免强光反射；3.4 角度：受检面与检验者视线成45度角；3.5 距离：将产品放置于距离检验者眼睛30cm处，使光线均匀从光盘面反射到眼睛；3.6 检查方法：产品从左到右仔细目测一次。4.0 缺陷分类：4.1轻微(Minor)：不影响使用，轻微影响外观或客户能够接受的缺陷4.2重要(Major)：非致命缺陷，不会影响使用功能，但客户难以接受的缺陷5.0 检验工具：目测 6.0 检验标准：Visual Criteria for Disc/光盘外观（目测）标准Label Printing Defect印刷不良正常标准Normal standard limit特殊标准(B+)Special standard limitD1分类 Classification1Smear化墨正面检测，轻微发现该缺陷 - 图案, 字体Not easy to see the defect from front view - picutres, words碟边 - 阔度 0.8mmdisc edge - width 0.8mm轻微 (Minor)2Ink spot, splash漏墨(穿网), 碟边渍墨正面检测，轻微发现该缺陷 - 图案, 字体Not easy to see the defect from front view - picutres, words阔度 0.5mmwidth 0.5轻微 (Minor)3Ink in middle ring中圈墨渍正面检测，轻微发现该缺陷 Not easy to see the defect from front view正面观看墨渍不显眼及放于白纸上墨渍少于1/3圆周Not easy to see the defect from front view, ink shorter than 1/3 of centre diameter轻微 (Minor)4 Registration走位 / 套字正面检测，轻微发现该缺陷 - 图案, 字体Not easy to see the defect from front view - picutres, words阔度 0.3mmwidth 0.3mm轻微 (Minor)5Wordings字体清晰度不可令图案、字体不能辨认pictures and words must clearly recognize不可令字样不清 - 阔度 0.3 mmpictures and words must clearly recognize - width 0.3 mm轻微 (Minor)6 Printing eccentricity印刷偏心两边印刷与碟边之相差 的平均值0.8mmThe average of the two distance differences between the image edge and disc edge 0.8 mm两边印刷与碟边之相差 的平均值0.8mmThe average of the two distance differences between the image edge and disc edge 0.8 mm轻微 (Minor) Visual Criteria for Disc/光盘外观（目测）标准Label Printing Defect印刷不良正常标准Normal standard limit特殊标准(B+)Special standard limitD1分类 Classification7Incomplete printing, missing ink塞网(缺划, 露银)正面检测，没有明显发现该缺陷 不可令字体不能辨认Not easy to see the defect from front view, words must clearly recognize直径 0.5 mm 及少于 5 点 及不可令字体不能辨认Not easy to see the defect from front view, words must clearly recognize轻微 (Minor)8Stain渍正面检测，没有明显发现该缺陷 不可令字体不能辨认Not easy to see the defect from front view, words must clearly recognize直径 0.5 mm 及 少于 5 点 及长度 4 mmdiameter 0.5 mm, less than 5 points, length 4 mm轻微 (Minor)9 Dust尘N/AN/A阔度 0.5 mm, 长度2mm, 少于 5点width 0.5mm, length 2mm轻微 (Minor)10 Color uneven 颜色不平均正面检测，两碟相并颜色差别不明显color deviation not easy to recognize from the front viewX-Rite色差仪, DE 15X-Rite( color checking device) will be used, DE should be less than 15重要 (Major)111.1 Color variation compare with pantone颜色与pantone 不符正面检测，两碟相并颜色差别不明显color deviation not easy to recognize from the front viewX-Rite色差仪, DE 15X-Rite( color checking device) will be used, DE should be less than 15重要 (Major)12 Water splash水渍正面检测，轻微发现该缺陷Not easy to see the defect from front view正面不明显, 阔度 4 cm, 长度4cmNot easy to see the defect from front view, width 4cm, length 4cm轻微 (Minor)Visual Criteria for Disc/光盘外观（目测）标准Label Printing Defect印刷不良正常标准Normal standard limit特殊标准(B+)Special standard limitD1分类 Classification13Water splash (line)水印 (线痕)正面检测，轻微发现该缺陷 - 图案Not easy to see the defect from front view - picture正面看不明显, 长度0.8cm, 少于5条 Not easy to see the defect from front view, length 0.8cm, less than 5 lines轻微 (Minor)14 Moire Effect线纹正面检测，轻微发现该缺陷 - 图案Not easy to see the defect from front view - picture正面不明显, 阔度 0.5 mm,长度2cm, 少于 5条Not easy to see the defect from front view, width 0.2mm, length 2cm, less than 5 lines轻微 (Minor)15 Printing scratch印刷刮花正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS正面不明显及长度 2mm及少于 5条 及 功能测试为合格Not easy to see the defect from the front view, length 2mm, less than 5 lines, Functional test PASS重要 (Major)16 Scratch on the information side碟面刮花正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS正面不明显及长度 2mm及少于 5条 及 功能测试为合格Not easy to see the defect from the front view, length 2mm, less than 5 lines, Functional test PASS重要 (Major)17Missing print漏印绝对不接受Not acceptable绝对不接受Not acceptable重要 (Major)Lacquer Defect沥架不良正常标准Normal standard limit特殊标准(B+)Special standard limit分类 Classification1 Lacquer spot沥架点不明显影响光碟图案外观Not affect the picture visually直径 0.5 mm, 少于 5 点diameter 0.3mm, less than 2 points轻微 (Minor)2 Radial vein太阳纹不明显影响光碟图案外观Not affect the picture visually不明显影响光碟图案外观Not affect the picture visually轻微 (Minor)Visual Criteria for Disc/光盘外观（目测）标准Lacquer Defect沥架不良正常标准Normal standard limit特殊标准(B+)Special standard limit分类 Classification3 Suction cup mark / Lacquer mark吸盘印、机械手的手指印/沥架印正面检测，轻微发现该缺陷 Not easy to see the defect from front view 阔度 0.5mm, 长度4mmwidth 0.5mm, length 4mm轻微 (Minor)4 Uneven lacquer on edge不平均沥架边 /沥架纹不明显影响光碟图案外观Not affect the picture visually阔度 1 mm, 长度1 mmwidth 1mm, length 1mm轻微 (Minor)Sputtering Layer Defect电镀层不良正常标准Normal standard limit特殊标准(B+)Special standard limit分类 Classification1 Pin Hole穿洞(含溅镀针孔)正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS阔度 0.5 mm功能测试为合格width 0.5 mmFunctional test PASS重要 (Major)2Dent缺口正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS阔度 1 mm功能测试为合格width 1 mmFunctional test PASS重要 (Major)3Sputtering layer eccentricity溅镀层偏心两边电镀层与碟边之相差的平均值1mmThe average of the two distance differences between the sputtering layer edge and disc edge 1 mm两边电镀层与碟边之相差的平均值1mmThe average of the two distance differences between the sputtering layer edge and disc edge 1 mm轻微 (Minor)Injection Defect注塑不良正常标准Normal standard limit特殊标准(B+)Special standard limit分类 Classification1 Flow mark, Silver steak气纹、流痕以不入该光碟内容位置为接受Accept if not in program area以不入该光碟内容位置为接受Accept if not in program area重要 (Major)2Cloud云影（水纹）正面检测，轻微发现该缺陷 Not easy to see the defect from front view 正面观看不明显Not easy to see the defect from front view 轻微 (Minor)Visual Criteria for Disc/光盘外观（目测）标准Injection Defect注塑不良正常标准Normal standard limit特殊标准(B+)Special standard limit分类 Classification33.1 Bump凹/凸点（尘点、凸包）正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS正面检测，轻微发现该缺陷功能测试为合格Not easy to see the defect from front viewFunctional test PASS重要 (Major