stm32课程设计报告.doc

利用TIM定时器的中断和定时功能实现跑马灯一、原理及目的 1、学习stm32库开发 2、理解和熟悉I/O的使用；3、进一步掌握定时器、中断处理程序的编程方法4、利用库函数开发实现跑马灯二、电路原理图三、流程图四、软件算法（代码）1、Main.c#includestm32f10x.h#includebsp_led.h#includebsp_TiMbase.hvolatileu32time=0;inti=0;intmain(void)LED_GPIO_Config();TIM2_Configuration();TIM2_NVIC_Configuration();RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);while(1)if(time=1000)time=0;i+;if(i=3)i=0;switch(i)case0:LED1(OFF);LED2(OFF);LED3(ON);break;case1:LED1(ON);LED2(OFF);LED3(OFF);break;case2:LED1(OFF);LED2(ON);LED3(OFF);break;2、led.c#includebsp_led.hvoidLED_GPIO_Config(void) GPIO_InitTypeDefGPIO_InitStructure;RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC,ENABLE); GPIO_InitStructure.GPIO_Pin=GPIO_Pin_0; GPIO_InitStructure.GPIO_Mode=GPIO_Mode_Out_PP;GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;GPIO_Init(GPIOB,&GPIO_InitStructure); GPIO_InitStructure.GPIO_Pin=GPIO_Pin_4|GPIO_Pin_3;GPIO_Init(GPIOC,&GPIO_InitStructure); GPIO_SetBits(GPIOB,GPIO_Pin_0);GPIO_SetBits(GPIOC,GPIO_Pin_4|GPIO_Pin_3); 3、led.h#ifndef_LED_H#define _LED_H#includestm32f10x.h#defineON0#defineOFF1#defineLED1(a) if(a) GPIO_SetBits(GPIOB,GPIO_Pin_0);else GPIO_ResetBits(GPIOB,GPIO_Pin_0)#defineLED2(a) if(a) GPIO_SetBits(GPIOC,GPIO_Pin_4);else GPIO_ResetBits(GPIOC,GPIO_Pin_4)#defineLED3(a) if(a) GPIO_SetBits(GPIOC,GPIO_Pin_3);else GPIO_ResetBits(GPIOC,GPIO_Pin_3)#define digitalHi(p,i) p-BSRR=i; #definedigitalLo(p,i) p-BRR=i; #definedigitalToggle(p,i) p-ODR=i; #defineLED1_TOGGLE digitalToggle(GPIOB,GPIO_Pin_0)#defineLED1_OFF digitalHi(GPIOB,GPIO_Pin_0)#defineLED1_ON digitalLo(GPIOB,GPIO_Pin_0)#defineLED2_TOGGLE digitalToggle(GPIOC,GPIO_Pin_4)#defineLED2_OFF digitalHi(GPIOC,GPIO_Pin_4)#defineLED2_ON digitalLo(GPIOC,GPIO_Pin_4)#defineLED3_TOGGLE digitalToggle(GPIOC,GPIO_Pin_3)#defineLED3_OFF digitalHi(GPIOC,GPIO_Pin_3)#defineLED3_ON digitalLo(GPIOC,GPIO_Pin_3)voidLED_GPIO_Config(void);#endif/*_LED_H*/bsp_TiMbase.c#includebsp_TiMbase.hvoidTIM2_NVIC_Configuration(void)NVIC_InitTypeDefNVIC_InitStructure;NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0); NVIC_InitStructure.NVIC_IRQChannel=TIM2_IRQn; NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=0;NVIC_InitStructure.NVIC_IRQChannelSubPriority=3; NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;NVIC_Init(&NVIC_InitStructure);voidTIM2_Configuration(void)TIM_TimeBaseInitTypeDefTIM_TimeBaseStructure; RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);TIM_TimeBaseStructure.TIM_Period=1000;TIM_TimeBaseStructure.TIM_Prescaler=71;TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1;TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up;TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure);TIM_ClearFlag(TIM2,TIM_FLAG_Update);TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE); TIM_Cmd(TIM2,ENABLE); RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,DISABLE);