提高动叶可调轴流风机液压缸运行可靠性的措施.doc_第1页
提高动叶可调轴流风机液压缸运行可靠性的措施.doc_第2页
提高动叶可调轴流风机液压缸运行可靠性的措施.doc_第3页
提高动叶可调轴流风机液压缸运行可靠性的措施.doc_第4页
提高动叶可调轴流风机液压缸运行可靠性的措施.doc_第5页
免费预览已结束,剩余22页可下载查看

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

/ /提高动叶可调轴流风机液压缸运行可靠性的措施摘要:根据现场实际遇到的问题及故障处理经验,结合理论知识,对动叶可调轴流风机液压缸提高运行可靠性进行系统分析,提出了解决思路并制订了相应设备维护管理对策及预控措施,以保证风机更安全的运行。关键词:动叶可调轴流风机;液压缸;运行;可靠性中图分类号:TH432.1 文献标志码:BMeasures of Improving Operating Reliability of Hydraulic Cylinder in Dynamic Blades Adjustable Axial Flow Fan Abstract:According to the actual problems and failure treatment experience, combining theory knowledge, the measures of improving operating reliability of hydraulic cylinder in dynamic blades adjustable axial flow fan are analyzed systematically. The solving thinking is put forward, and the relevant equipment maintenance management measures and control countermeasures are made to ensure the operation of fan more safely. Key words: dynamic blades adjustable axial flow fan; hydraulic cylinder; operation reliability0 引言0 the introduction 神华国华台电工程分两期建设,一期工程5600MW亚临界机组、二期工程建设41 000MW超超临界机组,并预留2台1 000MW超超临界机组场地,最终容量9 000MW。目前投运生产的5600MW、21 000MW机组共安装动叶可调轴流送风机14台,动叶可调轴流一次风机14台。动叶可调轴流送风机安装336/100液压缸,一次风机安装336/50液压缸。Shenhua guohua electric engineering in two phase construction, the first phase of 5 x 600 mw subcritical unit, the second phase construction of 4 x 000 mw ultra supercritical unit 1, and set aside 2 1 000 mw ultra-supercritical unit area, the ultimate capacity of 9, 000 mw. Current operation of the production of 5 1 x, 2 x 600 mw, 000 mw installation moving blade adjustable axial flow blower 14 units, moving blade adjustable axial flow blower 14 units at a time. Moving blade adjustable axial flow blower installed 336/100 hydraulic cylinder, and a fan installed 336/50 hydraulic cylinder. 经实际运行中发生的故障统计分析,液压缸故障是影响风机稳定运行的主要因素。By the actual fault occurred in the operation of statistical analysis to the hydraulic cylinder fault is the main factor that influence the stable operation of the fan. 下面将从液压缸工作原理、结构方面,对其常见故障进行分析,并制订相应的控制措施。Below from the aspects of working principle of the hydraulic cylinder, structure, analyzes the common faults, and formulate the corresponding control measures. 1 液压缸工作原理1 working principle of the hydraulic cylinder 动叶调节方式主要通过风机外侧电动执行机构带动风机液压缸伺服机构控制液压缸进油和回油,从而控制液压缸缸体进行往复运动,通过连接在缸体上的调节杆带动风机叶片进行调节见图1。Moving blade adjustment way mainly through lateral electric actuators to drive the fan fan hydraulic cylinder servo control of hydraulic cylinder oil inlet and the oil return, so as to control the hydraulic cylinder cylinder for reciprocating motion, by means of the adjusting rod connected to the cylinder drives the fan blades adjusted as shown in figure 1. 2 液压缸常见故障原因分析2 hydraulic cylinder common failure cause analysis 2.1 液压缸控制头内部反馈杆功能失效2.1 hydraulic cylinder rod control head internal feedback function failure 风机液压缸控制头内部反馈杆是保证高速旋转中把叶片稳定在合适角度的重要机构。反馈杆与缸体连接,随液压缸一起动作。末端有一个固定反馈轴承及锁紧螺母等部件。Fan control hydraulic cylinder head internal feedback pole is guarantee the stability of high-speed rotation of the blades at the right Angle of the important institutions. Feedback connection rod and cylinder, with the hydraulic cylinder motion. End bearing and lock nut has a fixed feedback etc. 功能失效的常见形式有:Common forms of function failure are: 1) 由于风机的振动,该螺母有时会发生松脱情况;1) due to the vibration of the fan, the loose nut sometimes happen; 2) 其它原因造成反馈轴承保持架损坏、锁紧螺母、限位卡簧脱落等缺陷。2) other causes feedback damage of bearing cage, lock nut, limit circlip fall off wait for blemish. 反馈杆功能失效后,液压缸在反馈过程中不能将调节系统的进油口封住,双面齿轮不能同步跟踪液压缸移动,致使动叶开度失控,风机不能正常运行。动叶将出现全开或全关的情况。至于向哪一个方向滑去要看固定螺母松脱后的油缸首先向哪一个方向移动。不论怎样移动,反馈系统都不能将风机叶片的开关角度固定在任意位置上1见图2。Feedback pole function failure, the hydraulic cylinder in the process of feedback control system can not be the inlet seal, double gear cannot move on synchronous tracking of hydraulic cylinder, the opening of the rotor out of control, fan can not run normally. The rotor will be fully open or close. As to which direction slippery to fixed nut to see the oil cylinder of loose after the first move in the direction of which one. No matter how to move, the feedback system is not to fix the switch of the fan blade Angle at any position on 1, as shown in figure 2. 反馈轴承保持架损坏原因主要有:Feedback bearing cage damage reason mainly has: 1) 动调头安装不好。1) move back bad installation. 运行中,反馈杆及反馈轴承内圈随液压缸一起旋转(为风机工作转速),液压缸中心找正工作效果直接影响反馈轴承(型号6 200)运行稳定性。如液压缸中心偏差超标(圆跳动允许误差00.03mm),将造成反馈轴承额外受力增大,寿命缩短。Run, feedback rod and bearing inner ring with the hydraulic cylinder rotate together (working for fan speed), the hydraulic cylinder center looking for bearing is working directly affect the feedback (model 200) running stability. Such as hydraulic cylinder center deviation exceeds bid 0 0.03 mm) (circular runout allowed error, will cause additional feedback bearing force increases, shorten service life. 液压缸检修过程中,反馈齿轮盖上的四个螺栓和弹簧垫圈如果放错位置,会碰到内部拨叉,将反馈轴卡死,轴承受力过大损坏。Hydraulic cylinder in the process of inspection, feedback four bolts for the gear cover and spring washer if put the wrong position, will encounter internal fork, will feedback shaft jammed, bearing load too much damage. 2) 油质不合格。2) oil is unqualified. 液压缸未按规定进行油质定期化验,油内含有水分(原因有冷油器泄漏、油站外壳密封不良雨水进入)引起伺服阀组锈蚀及损坏,易造成传动部件卡涩,橡胶密封件磨损,伺服阀不能正常工作。Hydraulic cylinder oil tests on a regular basis, not according to stipulations of oil contains water (cold reasons oil leakage, gas station shell seal into bad rain caused servo valve set of corrosion and damage, easy to cause jamming transmission parts, rubber seals and wear, servo valve cant work normally. 3) 控制头和机壳的扁铁拉条的螺栓未拧紧,控制头摆动。3) the control head bolts and the chassis of the flat iron brace does not tighten, control head. 控制头下方的螺孔是盲孔,螺栓不能过长,检修中易造成连接假象,使控制头摆动,反馈轴承受力过大损坏。Control head at the bottom of the screw holes are blind holes, the bolt is too long, easy to cause the connection when maintenance, make the control head swinging, feedback bearing load too much damage. 4) 反馈指示轴关节轴承卡涩不灵活。4) feedback indicates no flexible shaft joint bearing jamming. 控制头反馈杆通过齿条带动反馈齿轮,进而带动反馈指示轴旋转,使风箱外部就地叶片角度指针移动。反馈指示轴的关节轴承如缺少润滑,将发生卡涩情况,导致反馈杆及反馈轴承在移动过程中受力过大损坏。Feedback control head rod through a gear, rack and drive the feedback and feedback indicating shaft rotates, the bellows external in-place pointer blade Angle. Feedback indicating shaft bearing joints, such as lack of lubrication, jamming will occur, leading to feedback rod and bearing force is too large damage in the process of moving. 5) 反馈轴承质量差、润滑不良损坏。5) feedback bearing damage of poor quality, bad lubrication. 反馈轴轴承运行中除承受反馈杆旋转径向力,还承受液压缸移动带来的轴向力。其自身质量好坏决定了轴承的寿命。Feedback in the operation of the shaft bearing in addition to the feedback shaft rotation under radial force, also bear axial force hydraulic cylinder to move. Its quality is good or bad determines the bearings life. 6) 运行操作不当。6) improper operation. 运行人员每次的调节量过大或调节速率过快,很容易造成反馈杆轴承轴向受力过大,将反馈轴轴承磨损。同时一次调节量过大很容易造成轴套与轴之间内漏,造成油压波动。Operation staff every time the adjustment amount is too large, or adjustment of speed too fast, it is easy to cause feedback rod bearing axial force is too large, will feedback shaft bearing wear. At the same time, a large amount of adjustment is easy to cause between the shaft sleeve and the shaft leakage, oil pressure fluctuation. 2.2 风机液压缸因漏油导致油压波动、动作不良2.2 blower hydraulic cylinder oil pressure fluctuation caused by the spill, bad actions 风机液压缸依靠液压油压力推动缸体移动,达到叶片角度变化的结果。如液压缸系统发生内漏及外漏缺陷,将造成液压油压波动、下降,推力不足,液压缸动作不正常。Fan hydraulic cylinder on the hydraulic oil pressure to push cylinder body movement, blade Angle change results. Such as hydraulic cylinder system of leakage and leakage defects occur, will cause the loss of hydraulic oil pressure fluctuation, and thrust is not enough, the hydraulic cylinder motion is not normal. 发生漏油的原因主要有:The reason of leaks occurred mainly has: 1) 密封件质量差,装配不良,造成漏油。1) seal of poor quality, bad assembly, caused the spill. 液压缸找正偏差超标(圆跳动允许误差00.03mm)会引起主轴旋转偏心、动静密封间隙增大,进而造成漏油。液压缸滑阀磨损会导致和阀套之间间隙增大而造成漏油。液压缸活塞上密封圈故障将导致压力油与回油短路内漏,缸体动作异常。Hydraulic cylinder alignment deviation exceeds bid 0 0.03 mm) (circular runout allowed error will cause the spindle rotating eccentric, static sealing clearance increases, causing the leak. Hydraulic cylinder valve wear will cause gap between and valve sleeve increases caused by the leak. Hydraulic cylinder piston seal failure will lead to pressure on the oil and oil leakage in short circuit, cylinder body action. 2) 管路接头外漏。2) the pipe joint leakage. 液压缸外部连接进油管、回油管及泄漏油管铜密封垫圈失效,造成接头处漏油。Hydraulic cylinder outer joins into the copper tubing, return pipe and the leak sealing gasket, oil spill caused by tapping. 2.3 油管路未按记号连接,发生故障2.3 line did not press mark connections, failure happens 液压缸检修前必须做好油管路装配记号,回装时按记号装配。靠风机转子的接头接入高压油,外侧接头接入回油。如果油管路接反,就会造成伺服阀阀芯与反馈杆带动的伺服阀外套运动方向相反,伺服阀外套不能将进油口封住,风机叶片只能向全开全关方向运动,不能正常工作,严重时还会损坏动调头。Hydraulic cylinder repair pipeline assembly mark, must to do before back to the press mark when assembly. By the rotor of the fan connector connected to the high pressure oil, the lateral joint access to oil. If the pipe line, will cause the servo valve core and feedback pole to drive servo valve jacket movement in the opposite direction, coat of servo valve inlet opening can not be sealed, fan blades can only be fitted to the fully open direction, cant normal work, serious when still can damage to move back. 2.4 备用液压缸储存问题22.4 the spare hydraulic cylinder storage problems 2 液压缸正常使用的保险期受限于橡胶密封件的存放环境及使用条件。据国家标准,橡胶密封件应存放在25以下的室内。最好存放在15的不含除空气以外其他气体的环境中。存放期限为两年,温度及有害气体是加速橡胶密封件老化的主要原因。Hydraulic cylinder used normally deposit insurance is limited by the rubber seal of the environment and conditions of use. According to the national standard, the rubber seal should be stored in indoor under 25 . Best stored in 15 excluding other gases except air environment. Storage period for two years, temperature and harmful gas is a major cause of accelerated aging rubber seals. 3 提高风机液压缸运行可靠性控制措施3 fan hydraulic cylinder to improve operation reliability of control measures 3.1 提高液压缸装配质量,防止控制头内部反馈杆功能失效3.1 improve the quality of the hydraulic cylinder assembly to prevent the internal feedback control head rod function failure 1) 液压缸中心找正符合要求。1) hydraulic cylinder center looking for is in conformity with the requirements. 保证液压缸圆跳动允许误差00.03mm,在紧固螺丝后进行复检。应固定好限位螺丝并留出合适的限位余量,以保证限位装置工作正常。Ensure that hydraulic cylinder round beating permissible error 0 0.03 mm, for the re-inspection after fastening screws. Should be fixed limit screw and set aside the appropriate limit allowance, to ensure that the limit device is working properly. 2) 探讨对反馈轴承锁紧螺母防松形式改进。2) to investigate bearing lock nut locking on the feedback form to improve. 将固定螺母的外侧增加一个防松脱销钉。据了解有些电厂动调风机经过类似改进,收到了良好的效果。Will increase a fixed nut of the lateral locking nail out of stock. According to some fans after a similar dynamic adjustable power plant improvement, has received the good effect. 3) 提高密封件质量,保证安装工艺。3) improve the quality of the seals, ensure the installation process. 按照检修标准更换合格的耐油橡胶件,回装要缓慢细致,防止损坏O型圈。更换完成后必须进行打压试验,压力4.0MPa,持续时间5min无渗漏即为合格 3见表1。According to the inspection standard qualified replacement oil resistant rubber parts, returned it to slow, prevent damaged o-rings. Replacement must be crackdown after the completion of test, pressure is 4.0 MPa, the duration of 5 min to no leakage, qualified 3 are shown in table 1. 4) 控制头和机壳的扁钢连接牢固,避免控制头摆动。4) control head and flat steel casing connection is firm, avoid control head swinging. 连接输入、反馈轴时应保证联轴节两端面平行,螺栓要拧紧。控制头和机壳的扁钢连接牢固,防止控制头运行中摆动。Connected to the input, feedback should guarantee the two transverse coupling parallel shaft, to tighten the bolts. Control head and flat steel casing connection is firm, to prevent swinging in the operation of the control head. 5) 做好反馈指示轴关节轴承定期检查及润滑工作。5) prepare feedback indicates shaft joint bearing inspection and lubrication work regularly. 加强对反馈指示轴及操纵轴的就地维护保养,在关节轴承部位注入黄油(轴承座上有注油嘴)。Strengthen the feedback indicates the on-site maintenance shaft and manipulate the shaft, the joint bearing parts have zerk (bearing) into the butter. 6) 选用质量合格的反馈轴承、并保证润滑良好。6) use quality qualified feedback bearing, and guarantee good lubrication. 定期打开控制头后端盖检查反馈杆轴承质量情况,发现损坏及时进行更换。检查主轴和铜套之间间隙是否有堵塞情况,保证反馈轴承润滑供油量充足。Regularly open the control head rod bearing end cover after inspection feedback quality situation, found that damage to be replaced in a timely manner. Check whether there is gap between spindle and copper set of jams, ensure sufficient feedback bearing lubrication oil. 7) 运行操作合理,平稳。7) operation is reasonable and stable. 运行人员每次动叶调节避免调节速率过快,减少反馈部轴承轴向受力,延长轴承寿命。Operation personnel moving blade every time adjustment to avoid adjustment speed too fast, reduce the bearing axial force feedback department, extend the life of the bearing. 8) 提高检修装配质量,保证各部件配合间隙。8) improve repair assembly quality, to ensure all parts fit clearance. 液压缸各部件拆卸前,做好装配记号,尤其是反馈齿轮盖上的螺栓位置应正确。避免螺栓碰到拨叉,将反馈轴卡死,轴承拉坏。Completes the assembly prior to the demolition hydraulic cylinder parts, especially the feedback on the gear cover bolt position should be correct. Avoid bolt hit fork, will feedback shaft jammed, bearing pull bad. 9) 对油质定期化验,保证清洁度。9) for oil testing regularly, to ensure cleanliness. 按规定进行油质定期化验,颗粒度超标、油内含有水份及时更换,定期更换滤网、进行冷油器打压查漏工作。液压缸检修后缸内清理干净,无铁屑、杂质。Oil tests regularly according to regulations, the pellet degree of overweight, oil contains water, change in time, change regularly filter, cold oil leakage searching work on. Hydraulic cylinder tank is clean after maintenance, scrap iron and impurities. 3.2 采取措施消除漏油,避免发生油压油动、动作不良3.2 to take measures to eliminate leakage, avoiding hydraulic oil, bad actions 1) 选用质量合格的密封件,按工艺要求正确安装。1) choose quality qualified seal, install properly according to technical requirements. 选用质量合格进口的密封件、材质耐酸耐高温氟橡胶密封件(油封、O型圈),并按检修工艺安装。The quality qualification of imported seals, acid, high temperature resistant material, fluorine rubber seal, oil seal, o-rings, and installed according to the maintenance process. 2) 提高检修装配质量,减小液压缸中心找正偏差。2) improve repair assembly quality, reduce the hydraulic cylinder center alignment deviation. 保证液压缸圆跳动允许误差00.03mm,在紧固螺丝后进行复检。应固定好限位螺丝并留出合适的限位余量,以保证限位装置工作正常。Ensure that hydraulic cylinder round beating permissible error 0 0.03 mm, for the re-inspection after fastening screws. Should be fixed limit screw and set aside the appropriate limit allowance, to ensure that the limit device is working properly. 3) 按工艺要求正确安装,管路接头外漏。3) install properly according to technical requirements, pipe joint leakage. 液压缸外部油管接头的铜密封垫圈应在每次修理时调换,新铜垫圈应退火处理,油管接头紧力不得过大,防止损坏螺纹。Hydraulic cylinder external copper tubing joint sealing washer should be in every time repair replacement, new copper washer should be annealing treatment, tubing joint force shall not be too large, to prevent damage to threads. 4) 提高检修装配质量,保证各部件配合间隙。4) improve the quality of overhaul assembly, ensure that all parts fit clearance. 定期检查主轴与铜套配合情况,以满足配合间隙要求(配合公差最大间隙0.07mm,最小间隙 0.02mm),达到防止内漏的目的。Regularly check the spindle with copper set of circumstances, to meet the fit clearance requirements (maximum clearance fit tolerance of 0.07 mm, 0.02 mm minimum clearance), to prevent leakage. 3.3 油管路正确安装,避免接错。3.3 line installed correctly, to avoid wrong. 液压缸检修前,对各油管做好装配记号,进、出油管不得接反。Hydraulic cylinder overhaul before, for each tubing assembly, into and out of the tubing shall not be against. 3.4 保证滤油精度,减少滤网差压。3.4 ensure oil filter precision, reduce the filter differential pressure. 关注滤网运行差压,及时清理滤网,保证良好投入。继续探讨选用8m精度滤网可行性与可靠性。Focus on filter differential pressure operation, timely clean strainer, guarantee a good investment. Continue to probes into the feasibility and reliability of choose 8 microns precision filt

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论