DSLAM产品风扇监控配置方法.doc

/MA5300 set fan monitor/MA5300(config)#emu add 1 fan 0 0 ?- Command Of config-terminal Mode:-back COM port of EMUfore COM port of EMUMA5300(config)#emu add 1 fan 0 0 backMA5300(config)# FAULT MAJOR 2005-11-26 14:51:57 ALARM NAME : Emu abnormal PARAS INFO : FrameID: 0 EMU ID: 1 EMU Type: FAN Name: RESTORE MAJOR 2005-11-26 14:51:57 ALARM NAME : EMU recovery alarm PARAS INFO : FrameID: 0 EMU ID: 1 EMU Type: FAN EMU Name:MA5300(config)#MA5300(config)#show emu 1 EMU ID: 1 - EMU name : - EMU type : FAN Used or not : Used EMU state : Normal Frame ID : 0 Subnode : 0 COM port : Back -MA5300(config)#/MA5600 set fan monitor/MA5600(config)#emu add 0 FAN 0 0 com :back |name :fan Command: emu add 0 fAN 0 0 back fan MA5600(config)# ! FAULT MAJOR 2005-11-26 16:51:17 ALARM NAME :Emu abnormal PARAMETERS :FrameID: 0 EMU ID: 0 EMU Type: FAN Name: fan MA5600(config)#interface emu 0 MA5600(config-if-fan-0)#fan speed mode automatic Send command to environment monitor board ,please waiting for the ack MA5600(config-if-fan-0)# ! EVENT MAJOR 2005-11-26 17:07:11 ALARM NAME :Fan event information PARAMETERS :FrameID: 0 EMU ID: 0 EMU Type: FAN Control State: Auto timing Open State: Open MA5600(config-if-fan-0)# Execute command successful MA5600(config-if-fan-0)#display fan system parameter EMU ID: 0 FAN configration parameter: - FAN timing mode: Auto timing - Alarm_name Permit/Forbid Read temperature fault Permit Fan block Permit Temperature high Permit Power fault Permit - MA5600(config-if-fan-0)#quitMA5600(config)#display emu 0 EMU ID: 0 - EMU name : fan EMU type : FAN Used or not : Used EMU state : Normal Frame ID : 0 Subnode : 0 COM port : Back - /MA5100V100 set fan monitor/MA5100(monitor)%environment monitor fanon,off:on Config successfully.MA5100(monitor)%show fan configuration Fan work mode : AutoMA5100(monitor)%MA5100(monitor)%show fan state Fan Use Normal/MA5100V200 set fan monitor/MA5100(config)#emu add 0 fan 0 0 back |name :Command: emu add 0 fan 0 0 backMA5100(config)# ! 12005-11-26 17:41:27:PID_ALM-3-AlarmInfo: ALARM 4216 FAULT MAJOR 0x15411000 ENVIRONMENTAL 2005-11-26 17:41:27 ALARM NAME : Emu abnormal PARAMETERS : FrameID: 0 EMU ID: 0 EMU Type: FAN Name: DESCRIPTION : EMU is faulty or cannot communicate with the host CAUSE : (1) EMU fault, (2) Communication serial port damaged or line fault, (3) EMU reset manually ADVICE : (1) Replace the EMU, (2) Check the communication serial port and line.(3)No need to proceed - ENDMA5100(config)#interface ! 12005-11-26 17:41:30:PID_ALM-3-AlarmInfo: ALARM 4217 RECOVERY MAJOR 0x15421000 ENVIRONMENTAL 2005-11-26 17:41:30 ALARM NAME : EMU recovery alarm PARAMETERS : FrameID: 0 EMU ID: 0 EMU Type: FAN EMU Name: DESCRIPTION : EMU recovery alarm CAUSE : Communication between the board and the master board recovered ADVICE : No need to proceed - ENDMA5100(config-if-fan-0)#fan speed mode automaticCommand: fan speed mode automatic ! 12005-11-26 17:41:44:PID_ALM-3-AlarmInfo: ALARM 4218 EVENT MAJOR 0x15401000 - 2005-11-26 17:41:44 ALARM NAME : Fan event information PARAMETERS : FrameID: 0 EMU ID: 0 EMU Type: FAN Control State: auto timing Open State: Open DESCRIPTION : Fan speed-regulating mode or opening mode changes CAUSE : Environmental temperature or fan configuration parameter changed ADVICE : No need to proceed - END Send command to environment monitor board ,please waiting for the ackMA5100(config-if-fan-0)#show fan system parameterCommand: show fan system parameter EMU ID: 0 Fan configuration parameter: - fan timing mode: auto timing - alarm_name alarm(permit/forbid) read temperature sensor fault permit fan block permit temperature high permit