PDMS管道建模常用命令.doc

PDMS管道建模常用命令PIPEWORK名詞解釋PA : 管件進入點PL : 管件離開點P3: 管件第三點,如閥桿方向,TEE,OLETPOS:管件原點PH: BRANCH HEADPT: BRANCH TAILHREF: HEAD Reference (記錄branch head 接什麼)TREF : TAIL Reference (tail 接什麼)CREF : Connect Reference ( tee,olet 接什麼)建檔注意事項:1.同一PIPE中須CHANGE PEC或CHANGE 保溫時,請另建BRANCH,即同一BRANCH中PSPE/ISPE須相同.ELBODIR R 指定ELBO離開方向.管件定位方式-連接CONN -連接前一個MEMBERCONN TO NEX -連接下一個MEMBERCONN TO PT -連接至BRANCH TAILCONN AND P3 IS U -連接且P3 方向 IS UCONN PT TO LAST -結尾至最後一個元件FCONN -強制連接管件定位方式-距離DIST 100 FROm PREDIST 200DIST 100 FROM IDDIST 300 FROM PL OF PREVPOS PA DIST 300 FROM PL OF PRE 指定SPOOL 長度POS PA DIST 6000 FROM PL OF PREVPOS PA DIST 6000 FROM PL OF PRE COUP修改方位ORI AND P3 IS N45U -P3 點朝N45UORI AND PL IS D -修改RELIEF VALVE 之離開點方向FLOW BACK -建檔順序逆流向FLOW UNSET -建檔順序順流向選定物件PRENEXTENDSAMEFLAN 12/PW-101/PG-1301 跳至PG-1301BRANCH 查詢Q PHQ PTQ HREF Q TREFQ HCONNQ TCONNQ HBOREQ TBOREOELT/TEE 查詢Q CREFINST 查詢Q HEIGQ RADIQ ANGL新建管道新建Pipe，Branch建立Pipe，指定等級New Pipe /100-P-2003-2.5A1-ST(1)Pspec /2.5A1Ispec /IRWPTspec /1X25建立Branch，自動繼承等級New Branch /100-P-2003-2.5A1-ST(1)/B1Branch 頭尾連接 分支頭是PH，分支尾是PT CONN PH TO /1205-N5 (/1205-N5 is a Nozzle) CONN PT TO LAST MEM CONN PT TO /100-A8/T2 (/100-A8/T2 is a TEE) CONN PT TO P4 OF /VF205 (/VF205 is a VFWA.) CONN PH TO PT OF /100-A8/1 (/100-A8/1 is anotherBranch) CONN PH TO ID NOZZ新建元件Choose設置自動連接Choose AutoConnect On從Branch等級中選擇元件，顯示元件描述New Gask Choose Rtext（Or Stex，Ttex）New Flan Choose RtextNew Elbo Choose All通過Stype選擇元件New Elbo Choose With Stype ENew Redu Choose With Stype CONC Abor 100 Lbor 80Branch方向Branch方向轉換ForwardBackward反向配管BackNew Elbo Choose All反向從Branch Tail配管BackTailNew Gask Choose元件連接Connect與前一個連接Conn 與後一個連接Conn To Next強制連接Force ConnectFconnFconn To NextFconn To Tail改變方向Dir改變方向，同時修改Angle屬性Dir E繼續 改變P3點的方向Dir And P3 Is U45E元件繞軸旋轉Orientate一般用於旋轉P3點Ori And P3 Is Up改變元件出入口點改變Arrive