变速箱换挡叉的加工工艺及夹具设计(中英文文献).doc

毕业论文附件材料 目 录1 英文文献翻译.11.1 Shift gearbox .11.2 变速箱的换挡方式.121 英文文献翻译1.1 Shift gearboxClassification usually gearbox as follows:Manual transmissionThe general automatic gearbox / common automatic transmission with tiptronicCVT stepless gearbox with gear box of the /CVTDual clutch gearboxSequential gearbox(1) manual gearboxManual transmission, also known as manual gear, English name is manual transmission, referred to as MT, which push the shift lever to change gears meshing position inside the transmission, changing the transmission ratio, so as to achieve the purpose of speed. Step on the clutch, can move the shift lever.The working principle of a manual gearboxThe manual gear box is composed of different gear ratio of the gear group, its basic principle is through the gear group work in different, to realize the transformation of gear ratio. As the key link for power distribution, transmission must have the power input shaft and the output shaft of the big two, together constitute the transmission gear, is a manual transmission is the most basic component. The power input is connected with the clutch shaft clutch transmission, from the power to directly through the input shaft to the group, the gear set is composed of different diameter gear, gear power transmission effect of different proportion reached is completely different, the usual shift driving also refers to change gear ratio.Next, let us through a simple model to tell you, the principle of manual gearbox shift. Below is a simple structural model of 3 axis 2 speed gearbox.The input shaft (green) is also called the first shaft, connected by a clutch and engine, shaft and the gear is a hard connected components. Red is called the intermediate gear shaft. Enter the two gear shaft and intermediate shaft is in constant mesh state, so when the input shaft rotates will drive shaft rotation. Yellow is the output shaft, it is also called the second shafts and connected to the drive shaft (only for rear wheel drive, the precursor is generally two), and then through the differential drive vehicles.When the wheel rotates the same with spline shaft to rotate together, at this time, blue gear shaft can occur on the spline shaft relative free rotation. Therefore, the engine stops, and the wheel is rotated, the blue gear and shaft in the stationary state, and the spline shaft with wheels. The principle and the rear axle of the bicycle flywheel is similar. Blue gear and spline shaft is composed of a sleeve to connect, sleeve with spline shaft to rotate, but also can be free to slide on the spline shaft to gear.With these, the shifting process is very good understanding, when connecting sleeve and a blue gear, engine power will be transmitted to the output shaft through the shaft, at the same time, blue gear left in free rotation, but because there is no and sleeve engaged, so it does not affect the spline shaft. If the sleeve between the two blue gear, the gearbox in neutral position, the two blue gear on the spline shaft rotate freely, without mutual interference.Principle of a conventional 5 speed manual gearbox shift is the same, only the gearbox structure increased the number of sleeve and the gear sets, so that it has more gear. But the reverse is based on the intermediate shaft (red) and the output shaft (blue) is added between a gear to achieve. Due to the increase of a gear, the reverse gear will always rotate toward other gear in the opposite direction. The gear because only to change gear rotation direction function, so it is also called the idler.5 block two shaft transmission structure, the input shaft and the driving gear are integrated into a whole, simplifies the structure and saves spaceIn addition to the traditional three axis manual gearbox, the widespread use of cars is two axis manual transmission, its structure and the three shaft of the gearbox is similar, only the input shaft and intermediate shaft as a shaft, therefore has the advantages of simple structure, small size advantages, in addition, it also has the middle gear transmission high efficiency, and low noise characteristics, so it is more suitable to be the precursor home car general car transmission form, is currently the most widely used, its shortcomings is not set up direct gear, transmission and file than the design cannot be too high. While driving, three shaft gearbox used is still the traditional.Manual gearbox in general, is through the push rod is connected or cable to control the shift. Push rod shift control connection, more direct but vibration will be large; and the cable type although no vibration, but the shift is not very clear, it is each to have good and bad. In addition to shift the two pure mechanical control, in addition, and the use of electronic shift device of manual transmission, which can combine the merits of push and pull the shift between the good. This kind of gear box in the shift when the gear shift lever, shifting to the corresponding gear, the transmission will be motor drive the corresponding fork control sleeve and the gear is engaged, so that there is no gear is not clear, but the shift schedule can be controlled in the ideal range.So, a good manual transmission need to have what characteristic? The first transmission must have good gear handle, each gear position clear, have reasonable horizontal and vertical stroke, into the block resistance is small and with suction. What is more important is, the gear tooth between than arrangement must be reasonable. Because each gear position than distribution, directly affect the cohesion power vehicles moving in a smooth, usually require a low gear can effectively accelerate, high block to achieve high speed and efficient, and the distance between each block should be uniform, otherwise will be very easy to cause the channeling shift when the car.Analysis of the advantages and disadvantages of manual gearboxAdvantages Obviously, which is simple in structure, reliable performance, manufacturing and maintenance cost is low, and the transmission efficiency is high (theory will be more fuel-efficient), also, because it is pure mechanical control, shift reaction is fast, and can be more direct expression of drivers intention, and therefore more driving pleasure, these are the advantages of manual gearbox. But compared to automatic transmission, its operation is complicated, and frustration in gear switch when the obvious disadvantage is irreparable.(2) automatic gearboxAutomatic transmission AT, the full name of Auto Transmission, which is composed of hydraulic torque converter, composed of planetary gear and hydraulic control system, through the hydraulic transmission and gear combination to achieve variable speed moment.Compared with the manual transmission, automatic transmission is very different in structure and usage. The manual is mainly regulated by different gear combination to change gear, and the automatic transmission is through the hydraulic transmission and gear combination to achieve the purpose of changing speed. Hydraulic torque converter is one of the most characteristic of the automatic gearbox parts, which is composed of a pump, turbine and guide wheel and other components, pump wheel and turbine is a combination of work, through the liquid pump wheel drives the turbine to rotate, and the wheel between the pump and turbine wheel through the reaction between the pump wheel and turbine implementation the speed difference and implementation of variable torque function, the driver, you only need to different intensity slam the pedal, the gearbox can automatically stop lifting. Since the torque converter automatic transmission torque range is not big enough, so in a later series several rows of planetary gear to improve efficiency, the hydraulic control system will change with the engine to manipulate the planetary gear, so as to realize the automatic transmission torque. In order to meet a variety of running process needs (such as parking, reversing), automatic transmission also has some manual shift lever position, like the P block (R block (anchor), after the block), block N (neutral), D (forward), block.From the performance that the more gear automatic gearbox, the car in the process of running more smoothly, acceleration is better, and more fuel-efficient. In addition to providing a comfortable driving feeling, automatic transmission also has insurmountable defects. Dynamic automatic transmission response is not directly, which makes it in the driving pleasure slightly shortage. In addition, because of the use of hydraulic transmission, the automatic transmission gearbox transmission power loss.Tiptronic automatic transmissionHands appeared gearbox is in order to improve the automatic gearbox and operating economy and increase the setting, let the original computer automatic shift time back into the hands of drivers. At the same time, if in the city traffic in, or you can always switch back to automatic.A tiptronic automatic transmission is actually automatic gearbox, first appeared in a Porsche 911, manual gearbox electronic control system through the simulation of the operation of a manual gearbox. It appears, giving the driver a greater degree of freedom in the operation, can block up the blocking or shift paddles on the steering wheel to choose their own gear and shift the timing right, thereby greatly improving the driving pleasure.(3) CTV non-polar transmissionCVT (Continuously Variable Transmission), direct translation is a continuously variable transmission, which is continuously variable transmission. We often say, just as its name implies is that there is no clear and specific file, which operate on similar automatic gearbox, gear jump process but the ratio change is different from the automatic gearbox, but a continuous, so the power transmission continues smooth.CVT transmission system, the traditional gear by a pair of pulleys and a steel belt is replaced, each block is V structure is composed of two intervertebral disk, engine shaft is connected through a small pulley, steel belt drive pulley. Mystery lies in this special pulley: drive pulley structures CVT strange activity, divided into halves, can be close to or separate relative. Cone disc can tighten or open the thrust hydraulic, extrusion sheet steel chain so as to adjust the V slot width. When the cone disc inside mobile tightened, steel chain in the extrusion cones to center outside of the direction of movement (centrifugal direction), but moving to the center of the circle. In this way, steel chain drives the disc diameter increases, the transmission ratio is changed.The CVT gearbox what are the advantages?1, because there is no general automatic transmission gear, there will be no shift process of automatic transmission, shift the resulting sense of frustration will disappear, so the power output of CVT gearbox is linear, in actual driving very smooth.Theory of transmission system of 2 CVT, the gear can be an unlimited number of gear set, more freedom, the traditional transmission gear ratio, speed ratio and performance, fuel consumption, exhaust emissions balance, are more likely to achieve.3, the mechanical efficiency of CVT transmission, the province is oily considerably better than the automatic transmission common, after manual gearbox, fuel economy is much better than.Since there are so many advantages, why not let all the cars using CVT gearbox? There are two factors:1, compared with the traditional automatic transmission, its cost is high; and the operation is undeserved word, the higher probability.2, CVT gearbox itself still has its shortcomings, is the transmission of the steel belt can withstand strength is limited, generally more than 2.8L capacity or power above 280N M is its limit, but we also see that there are more and more cars such as Audi, or Nissan, has broken the limit, believe strip the problem will be solved gradually.(4) dual clutch gearboxDual clutch gearbox DCT, English name is Dual Clutch Transmission, because it has two clutches, so called dual clutch transmission.Technology introducedDual clutch gearbox combines the advantages of manual transmission and automatic transmission, no torque converter, instead of using two sets of clutch, through two sets of clutch alternately work, to achieve seamless shift effect. Two clutches respectively control the odd block and even block, that is to say, in the shift before, DSG had the next gear meshing, after shifting instruction, DSG quickly sends instructions to the engine, the engine speed increases, the previous meshing gears quickly, while the first group of clutch fully liberalized, the completion of a rise to block the action time, action and so on.Because without the torque converter, so the power of the engine can be fully played out, while the two clutch alternately work, shift time making, dynamic fault engine may be very limited. As the driver is the feeling that we are the most direct, switch gear action very quickly and smoothly, dynamic transmission process of almost uninterrupted, vehicle dynamic performance can be fully play. Compared with the traditional automatic transmission with torque converter, the DSG shift more directly, the power loss is smaller, so the fuel consumption can be reduced by more than 10%.DeficienciesHowever, with the traditional automatic transmission ratio, DSG also has some inherent disadvantages, firstly it is because there is no use hydraulic torque converter, nor realize manual transmission linkage action, so for the small-displacement engine, low speed torque characteristic is not enough to be completely exposed; secondly, because the DSG transmission using computer control, belonging to an intelligent transmission, it needs to send electronic signals to the engine block in the process of falling in the L /, the engine after reply, and the engine to be completed with L / reduction gear. A large number of electronic components, but also increases the probability of its failure.The dual clutch common with Volkswagens DSG, Ford Powershift, Mitsubishi SST and Porsche PDK.(5) sequential gearboxSequential gearbox (AMT) is improved on the traditional manual gear transmission based on; it combines hydromechatronics automatic transmission has the advantages of both AT and MT; AMT has the advantages of automatic transmission common automatic transmission, and the retention efficiency of the original manual transmission gear transmission, the high cost of low, simple structure, easy manufacture. It is the reform in the present manual transmission, retained most of the original assembly, only to change the shift lever manual operating system part, the production of succession, to transform the input costs less, is very easy to be manufacturers to accept.The driver through the accelerator pedal and joystick to the electronic control unit (ECU) control signal transmission; electronic control unit collects the engine speed sensor, the speed sensor signal, the time to master the running state of the vehicle; electronic control unit (ECU) based on the best program according to these signals stored therein, optimal shifting rules, clutch fuzzy control rules engine oil, adaptive control law, action and temporal separation of the engine, clutch and transmission shift binding, the three to achieve the best matching. In order to obtain the excellent fuel economy and power performance and ability to smooth start and rapid shift, in order to achieve the desired results.But the AMT transmission is not perfect, the biggest disadvantage of AMT gearbox is shifting comfort is poor, and generate power interruption in the process of shifting, the shift in the process of speed performance is not good.AMT mechanical gearbox, its basic structure and conventional manual gearbox consistent, generally only one input shaft and an output shaft (RWD usually a middle shaft), which generally is the input shaft 5 forward gear and output shaft gear is in constant mesh state, wherein the output shaft of the 1 gear and a reverse gear, 2 block and the 3 block, 4 block and 5 block were shared by the three shift fork. The mechanism of two adjacent gear with a shifting mechanism, when the shift action, fork need once upon a gear defect, through neutral to the next gear gear meshing, due to three actions is the order, even if each action will be the time to a minimum, is still very difficult to obtain the shift speed fast enough.Independent innovation shift forkThe ISR gearbox has a unique structure, the gear arrangement it is different with the traditional AMT gearbox, also different from the dual clutch gearbox. The use of four independent shift fork, two stalls adjacent to the gear shift fork is composed of different control. Four independent fork respectively control 1 gear and reverse gear; block 3 and block 5, block 2 and block 4, block 6 and block 7, that is to say, from 1 until 6 block, two adjacent stalls are composed of two independent fork to respectively control.Because of this design, the shifting process can be further shortened: when two adjacent gear to gear switch, a shift fork and the current gear gear detachment, another gear meshing has already started, and a shift fork action and activates the electronic clutch three, because the action is almost synchronously, so that the whole time shorten. Lamborghini is compared originally claimed, performance is very good before the generation of the E-gear sequential gearbox, shift speed upgrade 40%, shift speed of 50 milliseconds is close to F1 gearbox level.Gear shift mechanism of ISR is driven by the electric hydraulic pump, a