




免费预览已结束,剩余5页可下载查看
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
工程名称 Project description 射射线线检检测测报报告告 一一 Radiographic Examination Report I 单元名称 Unit description SH 3503 J123 1 第 Page 页 共 Total 页 Pages工程类别 Project description 检 件 名 称 Work piece description 检件编号 Work piece No 制造安装单位 Installation unit 报告编号 Report No 检 件 规 格 Work piece specifications 检件材质 Work piece material 执 行 标 准 Standard 检验比例 Check rate 合格级别 Class 射线源种类 设备型号 Type of ray source equipment tag No 胶片类型 Film type 焦距 Focal distance mm 胶片规格 Film specification 管电压 同位素类型 Tube voltage isotope type kV 增感方式 Increased sensitivity mode 管电流 活度 Current activity mA Ci 像质计型号 IQI type 曝光时间 Exposure time s 像质指数 Image quality indicator 拍 片 条 件 Conditions 透照方式 Exposure method 黑度 Darkness 总计 Total 张 Pieces 其中 一次返修 Of which 1st repair 张 二次返修 Pcs 2nd repair 张 三次返修 Pcs 3rd repair 张 Pcs 扩透 Additional pictures taken 张 Pcs 拍 片 数 量 Quantity 级 Class I 张 级 Pieces Class II 张 Pieces 级 Class III 张 级 Pieces Class IV 张 Pieces 评 定 结 果 Results 1 检测部位见附图 See the attached sketch for examination positions 检测结果见 射线检测报告 二 See Radiographic Inspection Report II for examination results 备 注 Remarks 检测人 Examined by 年 Y 月 M 日 D 审核人 Reviewed by 年 Y 月 M 日 D 检验专用章 Special examination stamp 工程名称 Project description 射线检测报告 二 射线检测报告 二 Radiographic Examination Report II 单元名称 Unit description SH 3503 J123 2 第 Page 页 共 Total 页 Page工程类别 Project category 检 件 名 称 Work piece description 检件编号 Work piece No 制造安装单位 Installation Unit 报告编号 Report No 底 片 编 号 Film No 透照日期 Date picture taken 缺陷性质 Defect nature 缺陷尺寸 mm Defect size 评定结果 Evaluation result 布片图号 Films arrangement drawing 缺陷性质 Defect nature C Crack 裂纹 P Porosity 圆形气孔 WP Worm Porosity 长形气孔 SI Slag Inclusion 夹渣 IF Incomplete Fusion 未融合 IP Incomplete Penetration 未焊透 UC Undercut 咬边 检测人 Examined by 年 Y 月 M 日 D 审核人 Reviewed by 年 Y 月 M 日 D 工程名称 Project Description 超超声声波波检检测测报报告告 Ultrasonic Examination Report 单元名称 Unit Description SH 3503 J124 第 page 页 共 Total 页 Pages工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation Unit 检件编号 Work piece description 报 告 编 号 Report No 检件规格 Work piece specification 检 件 材 质 Work piece material 执行标准 Standard 检 验 比 例 Inspection rate 合格级别 Qualification class 检件总量 Total Work pieces 检测数量 Number of Work pieces tested 检件类型 Work piece type 检验时机 Test time 表面状况 Surface condition 仪器型号 Apparatus type 探测波型 Wave type 耦 合 剂 Bounding agent 探头型号 Probe type 探头 K 值 K value of probe 补 偿 Compensation 标准试块 Standard test block 探测灵敏度 Sensitivity 抑 制 Suppression 灵敏度试块 Sensitivity test block 扫描线调整方式 Scanning line adjustment mode 探头扫查方式 Probe scanning mode 检 测 结 果 Inspection results 检测部位 编号 Inspection position Number 厚 度 mm Thickness 缺陷性质 Defect nature 缺陷尺寸 数量 Defect size quantity 评定级别 Evaluated class 评定结论 Evaluation conclusion 备 注 Remark 缺陷及返修情况说明 Explanation on defects and repairs 检测人 Inspected by 年 Y 月 M 日 D 审核人 Approved by 年 Y 月 M 日 D 检验专用章 Special inspection stamp SH 3503 J124 F 超超声声波波检检测测报报告告 续续表表 Ultrasonic Examination Report Continued 第 页 共 页 工程名称 Project Description 单元名称 Unit Description 工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation unit 检件编号 Work piece Number 报告编号 Report No 检 测 结 果 Inspection results 备 注 Remark 检测部位 编号 Inspection position number 厚 度 mm Thickness 缺陷性质 Defect nature 缺陷尺寸 数量 Defect size Quantity 评定级别 Evaluated class 评定结论 Evaluation conclusion 检测人 Examined by 年 Y 月 M 日 D 审核人 Reviewed by 年 Y 月 M 日 D 工程名称 Project Description 单元名称 Unit Description SH 3503 J125 超超声声波波测测厚厚报报告告 Ultrasonic Thickness Measurement Report 工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation unit 检件编号 Work piece No 报 告 编 号 Report No 检件规格 Work piece specification 检件材质 Work piece material 检件类型 Work piece type 仪器型号 Apparatus type 耦 合 剂 Bounding agent 表面状态 Surface status 检验比例 Inspection rate 检件总量 Total Work pieces 检测数量 Tested quantity 工件编号 Work piece number 测点编号 Measuring point number 公称厚度 mm Nominal thickness 实测厚度 mm Measured thickness 工件编号 Work piece number 测点编号 Measuring point number 公称厚度 mm Nominal thickness 实测厚度 mm Measuring thickness 检测结论 Inspection conclusion 检测部位示意图 Inspection positions diagram 检测人 Inspected by 年 Y 月 M 日 D 审核人 Approved by 年 Y 月 M 日 D 检验专用章 Inspection special stamp 工程名称 Project Description 磁磁粉粉检检测测报报告告 Magnetic Particle Examination Report 单元名称 Unit Description SH 3503 J126 第 Page 页 共 Total 页 pages工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation unit 检件编号 Work piece No 报 告 编 号 Report No 检件类型 Work piece type 检件规格 Work piece specification 检件材质 Work piece material 检验时机 Inspection time 表面状态 Surface status 检测比例 Inspection rate 执行标准 Standard 合格级别 Qualification class 仪器型号 Apparatus type 电流类型 Current type 检验方法 Inspection method 磁化方式 Magnetization mode 提 升 力 Lifting force 磁极间距 Distance between poles 磁化方向 Magnetization direction 磁粉种类 Magnetic particle type 悬 浮 剂 Suspension agent 磁化时间 Magnetization time 磁悬液浓度 Concentration 灵敏度试片 Sensitivity Work piece 检 测 结 果 Inspection results 检测部位 编号 Inspection location number 缺陷性质 Defect nature 缺陷尺寸 Defect sizes 评定级别 Evaluated class 评定结论 Conclusion 备 注 Remark 缺陷及返修情况说明 Explanations on defects and repairs 检测人 Tested by 年 Y 月 M 日 D 审核人 Approved by 年 Y 月 M 日 D 检验专用章 Special inspection stamp 工程名称 Project Description 磁磁粉粉检检测测报报告告 续续表表 Magnetic Particle Examination Report Continued 单元名称 Unit Description SH 3503 J126 F 第 Page 页 共 Total 页 Pages工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation unit 检件编号 Work piece No 报 告 编 号 Report No 检 测 结 果 Inspection results检测部位 编号 Test position No 缺陷性质 Defect nature 缺陷尺寸 Defect sizes 评定级别 Evaluation class 评定结论 Evaluation conclusion 备 注 Remark 检测人 Examined by 年 Y 月 M 日 D 审核人 Reviewed by 年 Y 月 M 日 D 工程名称 Project Description 渗渗透透检检测测报报告告 Penetration Test Report 单元名称 Unit Description SH 3503 J127 第 page No 页 共 total 页 pages 工程类别 Project Category 检件名称 Work piece description 制造安装单位 Installation unit 检件编号 Work piece No 报 告 编 号 Report No 检件规格 Work piece specification 检件材质 Work piece material 检件类型 Work piece type 检测时机 Test time 表面状态 Surface status 检测温度 Test temperature 执行标准 Standard 检测比例 Test rate 检测数量 Tested quantity 检 验 材 料 Test materials 牌 号 Brand 类 型 Type 渗 透 剂 Penetrative agent 清 洗 剂 Detergent 显 像 剂 Developer 检 测 结 果 Resul
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2025年中职美术面试题库及答案
- 浙江省温州市龙港地区2026届英语九年级第一学期期末复习检测试题含解析
- 山东省济宁市嘉祥县2026届化学九年级第一学期期中联考试题含解析
- 2026届吉林省长春市朝阳区化学九年级第一学期期中质量跟踪监视试题含解析
- 广西河池市两县2026届九上化学期中质量检测试题含解析
- 高级管理人员劳动合同解除与离职交接协议
- 离婚案中夫妻共同人寿保险权益分割及处理协议
- 跨国公司驻华代表处员工招聘及文化交流合同
- 离婚协议书:离婚后财产分割及共同债务清偿协议
- 私立小学教师绩效管理及职业发展规划合同
- 环保工程现场施工方案(3篇)
- 索尼微单相机A7 II(ILCE-7M2)使用说明书
- 疫苗行业疫苗研发创新报告:2025年重大疾病防控策略与研发创新趋势
- 印刷厂环保数据上报细则
- 一年级新生开学第一课常规训练
- 直播助农培训课件
- 劳动课美味凉拌菜课件
- GB/T 45707-2025皮革铬鞣鞋面用坯革规范
- 高空作业外墙漆施工方案
- 我和我的祖国课件
- 语言领域核心经验《学前儿童语言学习与发展核心经验》
评论
0/150
提交评论