光源英文说明书(180)

OPERATION INSTRUCTION XD 180 LAMP COLD LIGHT SOURCE 1 CONTENTS General Introduction n P2 P2 Character Summary P2 P2 Main technical parameters P3 P3 Working Conditions P4 P4 Basic Components and configuration P4 P4 Operation Operation description description P5 P5 NoticeNotice P5 P5 ChangeChange thethe lamplamp 2 P P 6 6 Troubleshooting Troubleshooting P7 P7 General Introduction Xenon cold light source which is not only a special instrument of light source but endoscopic supplementary equipment as well It can provide good and clear light source in clinical It also can provides the good illumination when doctor inspecting photographing video recording the body cavity organ 3 Character Summary 1 Using the advanced electrically controlled switching circuit provides the power source for the high pressured short arc Selects the ballhigh pressure short arc gas light as the luminophor Under the electric circuit high pressure causes the light bulb positive and negative electricity interelectrode shape electric discharge to shine produces ultraviolet from to the infrared entire spectrum radiation light source the visible range light extremely resembles the whitelight 2 Power source output current is ripple small and invariable make the arc light stable the optical efficiency high color is good In order to avoid other medical equipment movements produces high frequency chirp wave disturbance normal work We joined the low pass filter system in the power source enhanced the entire machine stability thus obtains satisfaction in the clinical observation photograph work 3 The cold light source output strong and the weak is depends on operating the kneadingboard to touch the switch to control In order to guarantee in the light source work movement stable and reliable we used three air blowersseries wind eta path strong radiation design makes the radiation fully guarantees the entire machine work stable 4 Carried out in the design and the production GB9706 1 Medical electric appliance equipment first part Safe general request can 4 guarantee its security Attention The cold light source does not have directly to use in an eye illumination Main technical parameters 1 external power supplies 220V 50HZ 2 power input 470W 3 fuse 5A 2 4 light bulbs powers 180W 5 color temperature 5600K 6 degrees of illumination 54800 000LX 7 working noises 55db 8 cabinets temperatures 55 degree 9 securities types I BFtype 10 Under normal works temperatures continuously leaks the electric current Unit mA Electric currentnormal statesingle failure condition To floor drain electric current 0 5 1 The patient leaks the electric current 0 1 0 5 5 The patient leaks the electric current to add the net voltage 5 Working Conditions 1 ambient temperatures 5 32 degree 2 relative humidity 70 3 atmospheric pressure 86 0 106 0kPa Basic Components and configuration 1 power switches Entire machine power source supplies 2 3 degrees of illumination regulating cock Adjustment degree of illumination size 4 luminous efficiencies mouths Leads the light beam continually connection Operation Operation descriptiondescription 1 guarantees the segment correctly the light beam and the luminous 6 efficiency mouth connection is reliable 2 turns on the cold light source power switch the cooling system starts to work The light bulb lightens immediately the lightsource starts to work 3 press button may transfer the degree of illumination from biggest to zero move brightly moves darkly When finish the job adjust the lightsource brightness to the lowest later closes the power switch guarantees the entire machine full cooling before turn off the machine NoticeNotice 1 When work the cold light source should lay aside toventilates and the steady place Radiation hole and the back cover supposed to maintain the 15cm space length 2 In work do not let the patient contact the cold ligh tsource 3 After light sources start for 120 seconds the facula to appearthe vibration belong to the normal phenomenon 4 After cold light sources open do not to look straight ahead the optical cable with the naked eye or the light loses the pore prevent eye to receive the injury 5 When work the engine case does not have to lay aside other goods 6 The cold light source is loaded with the ultrahigh voltageshort arc mountain lamp do not fierce vibration be careful of transportation 7 When do not use cold lightsources should deposit toventilates and the 7 dry place and must add the safety mask 8 Carry on the disinfection with the ultraviolet sterilization regularly 9 Has the high tension circuit do not turn on the engine case besides he machine repair personnel ChangeChange thethe lamplamp 1 When replaces the light bulb should select same model highpressure short arc xenon or the same parameter import light bulb can guarantees the cold light source normal 2 Closes the power switch 3 Machine box lid opening slowly turn on the engine s ventilator lap twist the light bulb negative pole segment and three anchor screws will take out the old lightbulb and exchanges the new light bulb 4 When install new light bulbs must pay attention to the light bulb localization aim at light gap screws tight three fixed anchor screws twists the ventilator lid 5 From the engine case base pulls out the light bulb anode segment with the orange black to fix together on the wiring column covers the back lid Attention The light bulb anode segment does not have to touch with cold light source engine case and must maintain the enough distance 8 TroubleshootingTroubleshooting be supposed to operate by specialist 1 After turns on the power source the indicating lamp is not bright the air blower and the light bulb do not work 1 inspects whether the alternating current supply is normal 2 inspects whether the fuse blows a fuse The fuse altogether has two behind the cabinet is the tubular5A 2 air blowers work but the Xenon is not bright 1 turns on the cabinet dismantles the line board and the trigger two attachments with the direct current electric instrument measuring circuit board output voltage the n