LED电源规格书.doc

深 圳 市 东 观 兴 科 技 有 限 公 司 SHENZHEN East-DG Technology Co.，Ltd. 客户承认书SPECIFICATION FOR APPROVAL客户名称CUSTOMER： 湖北方正 客户物料CUSTOMER PART NO:： 产品型号MODEL NO： DG-L103D 产品规格PRODUCT TYPE： 12串26并 客户确认 CUSTOMER APPROVAI检查 TESTED BY:审核CHECKED BY:批准APPROVED BY:请回签一份带贵司签名规格承认书PLEASE RETURN TO US ONE COPY OF “SPECIFICATION FOR APPROVAL” WITH YOURAPPROVED SIGNATURES地址:深圳市石岩镇洲石路恒超工业园A栋4-5楼 http:Add:F4-5,Bldg .A, Hengchao Industrial Park, Zhoushi Road, Shiyan Town, Shenzhen, Guangdong, China电话TEL传真FAX定 WORKED BY: 审核CHECKED BY: 批准APPROVED BY:变更覆历E.C.LIST版本Rev变更内容描述Description of Change日期DateECN NO变更前Before变更后AfterA初次发行Original Release目录Table Of Content1.产品描述Description.42.输入特性Input Characteristics43.输出特性Output Characteristics54.负载特性load Characteristics.55.安规标准Safety Standards.66.电磁干扰标准EMI Standard.67.电磁兼容标准EMC Standard68抗电磁干扰标准EMS Standards.79.保护功能Protection Functions810.环境要求Environmental Requirements.911.可靠性要求Reliability Requirements.912.外形尺寸Outline Size.1013.使用说明Instruction1014.注意事项Notice.1115.联系方式Contact.1216. 声明Announce.12 1、【产品描述Description】DG-L103D是我司专为LED灯开发的一款宽电压输入的隔离型恒流驱动电源，该产品采用独特的隔离型设计方案，关键元器件采用进口品牌，该产品具有节能、环保、安全、长寿命等特点。DG-L103D belongs to the wide range input isolated constant current driving power supply is specially designed for the LED Lamps. Unique self-R&D isolated program has been adopted. All the main components was imported & old-establishedones. energy-saving, eco-friendly, safe, longlifespan. 2、【输入特性 Input Characteristics】名称Name最小值Min. Load额定值RatedLoad最大值Max. Load单位Units备注Remark输入电压InputVoltage90110/220264Vac输入频率InputFrequency4750/6063HZ输入电流Input Current0.27A90Vac 满载90Vac Full load功率因数Power Factor0.98 110Vac 满载110Vac Full load0.95 220Vac 满载220Vac Full load效率Efficiency88%110Vac 满载110Vac Full load90%220Vac 满载220Vac Full load电流谐波Currentharmonics15%110Vac 满载110Vac Full load20%220Vac 满载220Vac Full load3、【输出特性Output Characteristics】名称Name最小值Min. Load额定值RatedLoad最大值Max. Load单位Units备注Remark输出电压OutputVoltage273642Vdc220Vac输出电流Output Current513516518mA220Vac输出纹波Output Ripple333V220Vac4、【负载特性load Characteristics】名称Name最小值Min. Load最大值Max. Load单位Units备注Remark开机延迟时间Start-upDelayTime 2 S 110Vac 满载110Vac Full load 1 S 220Vac 满载220Vac Full load上升时间Rise-up Time 150 mS 110Vac 满载110Vac Full load 100 mS220Vac 满载220Vac Full load输出过冲Output Overshoot 10%V110Vac 满载110Vac Full load 10%V220Vac 满载220Vac Full load输出欠冲OutputUndershoot 10%V110Vac 满载10Vac Full load 10%V220Vac 满载220Vac Full load输入线性调整率InputLineRegulation10%40Vdc 满载 40Vdc Full load10%27Vdc 满载 27Vdc Full load输出线性调整率Output LineRegulation10%110Vac 满载10Vac Full load10%220Vac 满载220Vac Full load5、【安规标准Safety Standards】5.1抗电强度DielectricStrength输入对输出Input&Output：3750VAC/5mAmax/3s5.2绝缘阻抗InsulationResistance输入对输出Input&Output：4M500Vdc5.3电气安全间距Electric Safety SpaceL/N输入间：3mm L/N spacing: 3mm初次级间：6.5mm Spacing between theprimary and secondarycoils: 6.5mm保险丝焊盘间：3mm Spacing between the fuseand bonding pad: 3mm6、【电磁干扰标准EMI Standard】EN 55015:1998,+A1:2000 +A2:2003,CLASS B.7、【电磁兼容标准EMC Standard】7.1 EN 61000-3-2:谐波电流的排放Harmonic current emissions.7.2 EN 61000-3-3:电压的波动Voltage fluctuations&flicker7.3 EN 61000-4-2: 静电放电：空气放电8千伏，接触放电4千伏Electrostatic Discharge (ESD): 8KV air discharge,4KV contact discharge.7.4 EN61000-4-3: 辐射频率电磁场敏感试验Radio- frequency Electromagnetic Field Susceptibility Test(RS).7.5 EN61000-4-4: 迅速电子脉冲 Electrical Fast Transient / Burst (EFT).7.6 EN61000-4-5: 抗电涌试验 Surge lmmunity Test: Power Line to Line: 2KV7.7 EN61000-4-6: 传导辐射频率干扰 Conducted Radio- Frequecy Disturbances (CS).7.8 EN61000-4-8:电源频率磁场测试 Power Frequency Magnetic Field Test.7.9 EN61000-4-11:电压骤降Voltage Dips.8、【抗电磁干扰标准EMS Standards】8.1雷击浪涌抗绕度Lightning Surge Immunity 此产品符合IEC-61000-4-5等级2的需求/This is to follow the norm of IEC-61000-4-5 Level 2requirements：L-N 之间打1KV电压，5次之后没有功能损坏。 L-N 1KV 5 times No function error.8.2电脉冲群抗绕度Electric Fast Transients Immunity此产品符合IEC-61000-4-4等级4的需求This is to follow the norm of IEC-61000-4-4 Level 4requirements：L-N 之间施加4KV，2.5KHZ干扰电压，1分钟之后没有功能损坏。L-N 4KV，2.5KHZ 1Minute Nofunction error.9、【保护功能Protection Functions】开路保护：输出端无负载开路时，输入端正常输入，产品无损坏。Open Circuit Protection: when the output end is connected with nothing, the input end with a designed input voltage, protection mode works & the product wont be damaged短路保护：如果输出端出现异常，造成输出正负极短接，本产品会工作在短路模式。 Shot Circuit Protection: when the output end was wrongly connected & lead to shot circuit, the protection mode works & this supply wont be damaged.过载保护： 本产品恒流设计，负载在设计范围内，输出电流会恒定不变，当输出端负载超出设计范围，本产品进入保护状态。Over Load Protection: This product is designed to work in constant current, taking into consideration of outer load. The output current will be constant, when the output load beyond the design, the protection mode works.输入端保护：当供电系统中出现瞬间高压脉冲（如雷击等），保护电路将启动，避免后端电路及负载受到伤害。Input Protection: When Instant High voltage exits in the power supply system, protection circuit turns on & works, to protect the other circuit & equipment.10、【环境要求Environmental Requirements】工作温度Operating Temperature：-30 to +60工作湿度Operating Humidity：20%RH to 80%存储温度Storage Temperature：-40 to +80 大气压力Pressure：70KPa to106 KPa11、【可靠性要求Reliability Requirements】11.1老化测试Reliability Test：产品100%要在至少40 5的环境及满载条件下老化4小时。100% of products The power supplyshall under go a minimum of 4 Hours burn-in test at 40 5 under full load condition11.2平均间隔故障时间估算Mean Time Between Failures：产品至少20,000 小时,25环境及额定输入与满载条件下,质保三年。This supply shall be guaranteed with 3 years warranty, within 20,000 hours, with environmental temperature of 25 & full load condition.12、【外形尺寸Outline Size】外形尺寸Outline size：L*W*H=249mm*17mm*10mm13、【使用说明Instruction】一端标示有L、N字母的为AC输入端，此端接AC90-264V交流输入电压；另一端为DC输出端，电源板上标识有LED+与LED-，LED+接LED灯的正极，LED-接LED灯的负极。The end marked withL& Nis the AC Input terminal & should be connected with AC90264V of input voltage; the other end is the DC output terminal and marked with LED+ & LED-, the LED+ should be connected with the positive pole & LED- with the negative one.LED -NLLED +产品接线示意图如下Wire splice picture hereof：VinAC90-264VLEDDRIVERSLED+LED-LN14、【注意事项Notice】1、在装置电源时，请注意输入、输出端的正确安装，确认无误后才能通电；When fit the power supply, please, pay attention to correctly connect the input & output ends. We should further ensure the correct connection, then turn on the electricity2、电源在第一次装置好电气连接后，如出现不亮或其它相应现象时，请切断AC输入端并检查DC输出端有无接触不良或AC输入端有无接触不良；When first fix the power supply with the other equipment, if the LED doesnt light up or other phenomenon exits, please cut off the AC input end & check whether there is some bad or poor contact with the DC output end and AC input end. 3、在装置好电气连接后，并且LED灯点亮，但输出异常时，请切断AC输入端检查DC输出端有无过载、超载；When fix the supply with the LED, and light it up,something wrong happen to the output.