华为MA5605开局参考脚本.doc

rootadmin 用户名和密码enable 进入特权模式下#config terminal 进入全局配置模式下#(config)#(config)hostname YF_LDLT_HuangJingLangCunWei_MA5605 设备命名(根据局里要求来命名)huawei(config)#inter lan 0/0 进入主控板0框0槽huawei(config-lan-0)#vlan 61 添加网管VLANhuawei(config-lan-0)#vlan 1481huawei(config-lan-0)#vlan 1482. 添加业务VLAN (从1481到1544)-根据实际情况添加huawei(config-lan-0)#vlan 1481 to 1544 common 如果设备升级后可以批量添加VLANhuawei(config-lan-0)#exit huawei(config)#nms 61 设置带内网管VLANhuawei(config)#atmlan ip-add eth 172.16.7.228 255.255.255.0 设置IP地址(根据具体情况设置)huawei(config)#atmlan ip-route 172.16.1.0 255.255.255.0 172.16.7.1 设置路由网关huawei(config)#atmlan ip-route 202.104.197.96 255.255.255.224 172.16.9.1huawei(config)#atmlan ip-access 172.16.7.1 172.16.7.254 255.255.255.0 设置访问列表(根据各县市要求来添加)huawei(config)#atmlan ip-access 172.16.1.0 172.16.1.254 255.255.255.0huawei(config)#atmlan ip-access 202.104.197.97 202.104.197.126 255.255.255.224huawei(config)#traffic-profile 6144 8 增加流量表项huawei(config)#autosave 1440 设置设备自动保存时间为1440分钟/次huawei(config)#adsl line-profile add 2/3/4/5/6 建立速率模板，512K,1M,2M,4M,6Mhuawei(config)#adsl line-profile add 2 During input,press Q to quit,then settings at this time are neglected. Select the line profile type 1-adsl 2-adsl2+(12) 1: 2 都是选择2，表示长距离板 Will you set basic configuration for modem? (y/n) n: Will you set channel mode? (y/n) n: y Please select channel mode 0-interleaved 1-fast (01) 0: 1 Will you set interleave delay? (y/n) n: Please select form of transmit rate adaptation in downstream: 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (02) 1: Will you set noise margin for modem? (y/n) n: Will you set parameters for rate? (y/n) n: y Min bit rate in down stream (3232000 Kbps) 32: Max bit rate in down stream (3232000 Kbps) 32000: 512/1M/2M/4M/6M Min bit rate in up stream (323000 Kbps) 32: Max bit rate in up stream (323000 Kbps) 3000: 512 Please input the profiles name : Add profile 2 successfully. huawei(config)#int adsl 0/1 2 3 4 进入每块单板，从1号槽位开始huawei(config-ADSL-0/1)#deactivate all 去激活该单板所有端口huawei(config-ADSL-0/1)#activate all 2 用2号模板激活该单板所有端口(根据实际需要选择模板)huawei(config-ADSL-0/1)#deactivate * 去激活该单板某个端口huawei(config-ADSL-0/1)#activate all * 2 用2号模板激活该单板某个端口huawei(config)#pvc adsl 0/1/1 0 35 lan 0/0 1481 1483b 0 on on 8 8 建立xDSLLAN的PVC，每个端口加两条 pvc adsl 0/1/2 0 35 lan 0/0 1482 1483b 0 on on 8 8 pvc adsl 0/1/3 0 35 lan 0/0 1483 1483b 0 on on 8 8 . 修改端口号及业务VLAN继续添加设备升级后必须这样添加PVC：pvc adsl 0/1/1 0 35 lan 0/0 1481 0 disable 1483b on on 8 8pvc adsl 0/1/2 0 35 lan 0/0 1482 0 disable 1483b on on 8 8pvc adsl 0/1/3 0 35 lan 0/0 1483 0 disable 1483b on on 8 8pvc adsl 0/1/4 0 35 lan 0/0 1484 0 disable 1483b on on 8 8pvc adsl 0/1/5 0 35 lan 0/0 1485 0 disable 1483b on on 8 8 。huawei(config)#snmp-server enable traps 允许设备发送Trap报文huawei(config)#snmp-server contact HUAWEI-075528560333 设置系统联系信息huawei(config)#snmp-server location YF_LD 设置系统位置信息huawei(config)#snmp-server community N2000 172.16.1.8(网管IP地址) public private notify 162 v1 增加团体名huawei(config)#save 保存数据huawei(config)#ping 172.16.7.1 ping网关检查是否与网管相通huawei(config)#terminal language 语言切换huawei(config)#show adsl line-profile all 查看所有的速率模板，1和33为系统自带的，尽量不要修改- - - - - - -profile operating channel min down max down min up max upindex mode mode rate rate rate rate(Kbps) (Kbps) (Kbps) (Kbps)- - - - - - -1 All Interleaved 32 6144 32 6402 All Fast 32 512 32 5123 All Fast 32 1024 32 5124 All Fast 32 2048 32 5125 All Fast 32 4096 32 5126 All Fast 32 6144 32 51233 All Interleaved 32 32000 32 3000-Total: 7huawei(config)# show board 0 查看所有单板状态 Slot ID Board Type Board Name Board State - - - - 0 FE H521MFOA Normal 1 ADCE H523ADCE Normal 2 Empty - - 3 Empty - - 4 Empty - - -huawei(config)# show board 0/1 查看第一块单板的状态 Frame Slot Board Type Board State Interface Type PVC Number - - - - - - 0 1 ADCE Normal - 32 - - - - - - Port State LineProfileId AlarmProfileId ExtLineProfileId - - - - - 1 Activating 4 1 - 2 Activating 4 1 - 3 Activating 4 1 - 4 Activating 4 1 - 5 Activating 4 1 - 6 Activating 4 1 - 7 Activa