




已阅读5页,还剩3页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
BIK Shanghai International Ltd.Tel: +86 21 Fax: +86 21 File No.: BIK.QC-FI-05Quality Control Checklist-Wood Furniture1. Rough Mill:1.1 Check moisture content on lumber in kiln. Check moisture on plywood parts.1.2 Check to insure rough cut parts are the correct length, width, height or thickness to allow for machining.1.3 Check to insure there are no dead knots in the parts and that the live knots conform to product quality requirements.1.4 Inspect for wind shake, splits, honeycombs, cracking, etc.2. Lamination Department:2.1 Insure that parts to be laminated are laminated on both sides before clamping.2.2 Insure that grain direction is reversed on all parts being laminated.2.3 Inspect for moisture content after the lamination process.2.4 Inspect for rough cut sizes to insure allowances are made for machining, length, width, height or thickness.3. Machine Department:3.1 All parts need to be checked for proper size and machining according to the detail.3.2 Inspect moisture content. (If moisture content is above 8% re-dry parts.)3.3 All parts machined to spec sheets and FC standard spec Bk.3.4 There are no parts splitting or cracking.3.5 There are no open grains.3.6 Check for parts being square when applicable.3.7 Dry fit parts to check for proper fit.3.8 Check all right angles.3.9 Inspect tops with straight edge for warping.3.10 Check Rab Parts for proper depth and consistent machining.3.11 Check that all reveals are clean at 90% and uniform in size and length.3.12 Inspect door style, door, side panels, parting rails, etc. For proper construction and warping (Use straight edge).3.13 Check all board and mortised parts for proper size boring and tennon.3.14 Check all miters and compound miters for consistency and fit.3.15 Check boring for hardware, shelves and adjustable shelf hole spacing.3.16 All reveal and tops are uniform in size.3.17 Insure that bunn feet that cannot be turned into the carcuss post have the correct dowel length.4. Carving Department:4.1 Check that all carvings are consistent and complete. ( Used mirror image concept)5. Pre Assembly:5.1 Check to insure that parts fit properly.6. Pre Sanding - Parts Sanding:6.1 Insure all parts are sanded properly.6.2 Insure that the edges are broke on all parts.6.3 Pre-fill all tops that have open grain.7. Assembly:7.1 Check carcuss to insue proper fit at all joints and that they are properly glued and screwed.7.2 Insure the carcus is leveled. (Sits Level)7.3 Check outter carcus for square.7.4 Check all door and drawer compartments for square and proper dimension.Check carcus top for level, front, back, and sides (Use straight edge)7.5 Insure that all items are strong and stable. (Use-weight test by applying minimal pressure)7.6 Check corner blocks to insure they have been glued and screwed.7.7 Check parting rails to include dust bottom for proper fit and that they are not warping.7.8 Check all under arts for uniformity. (Table Apron)7.9 Check to insure proper bridging is installed on all tables.7.10 Check for proper Drawer Costruction and pitch.7.11 Check for proper shelf fitting and clearnce for no sticking and proper clearance. ( By F.C Specs Book)7.12 Check to insure that all inside and out side dimensions are correct according to the overall size.7.13 Check chair seat depths.7.14 Insure that all pitchs conform to specifications.7.15 Insure no gauges, scratches, dents, nails or splintered areas are on the item.7.16 All drawer and door deges need to be rounded. (Hand Sand Edges)7.17 Insure that all overlays have been properly alligned, glued and pinned nailed.7.18 All doors and side panels being a solid or veneered panl must have a floating panel construction. (Check Spec. Book for Construsction) 7.19 Check all legs for champer and rounding.7.20 Insure all bunn feet have been glued and screwed.7.21 Insure back panels are square and screwed on not glued.7.22 Check tops for proper instillation, fit and screwing.7.23 Insure brass is permanently fixed with epoxy and nailed, and taped for finishing purposes.Unit Sanding: 光泽Insure that proper sanding is done throughout the entire case.Insure all carvings are flutter sanded and hand sanded.Insure all gauges, dents, scratches, cracks it are filled and sanded.Cracks and splits 1/8” or larger need to be slivered.No veneer used for patching on solid pieces.Patch follows grain in existing item as much as possible and patch does not have definite shape. EX. Square, round, oval, ect.All patches should be 1/4” in thickness for solid pieces.Check for glue runs.Polish SandingCheck surfaces inside and out for consistent sanding.Check carvings for proper final sanding.Finishing:Insure proper materials are being used according to the step panel.Insure the inside finish is consistent and matches the outside.Overall finish is even and consistent.Tops, bottoms and back panels of items are to be finished.All surfaces are smooth and free of overspray.Check for the finnish cracking and peeling.Check for runs and fingefrprints in the finish.Insure drawer interiors are finished correctly.Check to insure all hand paintings are correct and consistent.Check final color against sample for variation.Packing:Before packing check to insure all hardware and hinges are installed correctly.Check joints for cracking.Allitems need to be blown off with air hose and inspected.Check to insure all interiors are clean.Check glass insert for proper fit.Check mirror insert fo proper fit.Check moisture content.Insure all items are wrapped in 4mm plastic proir to shipment.Stone Casting:Check for any imperfection in the stone.Inspect molds on a regular basis.All cast should be free of flat seams.Check for hair line cracks.Check for adjustable glides on all dining tables. When applicable.Check for level surfaces for all items that require lay on glass.When applicable check items for square and level.When stone and metal are casted together issure there are no gaps or holes when they are joined.Insure items without adjustable glides sit level.Check dimensions according to the detail.Metal:Insure all items are level.Insure items that require lay on glass the surface is level.Insure dimensions are correct according to the detail.When possible adjustable glides need to be added to dining tables.Check for grinding or
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2025年下半年吉林延边公交集团公开招聘10人易考易错模拟试题(共500题)试卷后附参考答案-1
- 高铁制梁场复垦施工合同(3篇)
- 高速公路改造合同模板(3篇)
- 安全施工考试题及答案
- 高明租房合同台账模板(3篇)
- 事业单位聘用合同解除与竞业限制期限合同
- 2025河南公务员面试题及答案
- 《中小学校学生家长参与学校课程改革协议》
- 股权代持解除与控制权恢复-法律程序与执行合同
- 中央预算单位公务卡支付结算与财务管理合作协议
- 中职女生健康教育
- 单位集中物业管理保洁服务方案方案投标文件(技术方案)
- 外事礼仪培训课程
- 2025至2030中国玄武岩纤维行业发展趋势分析与未来投资战略咨询研究报告
- 作业托管学生管理制度
- 《机械制图》机械工业出版社 第一章 制图基本知识与技能 章节过关卷(原卷版)
- 公安接警面试题及答案
- 动力电池回收网络设计-洞察及研究
- 中国心血管病一级预防指南解读
- 贝壳融合训acn试题及答案
- 鸿蒙试题及答案
评论
0/150
提交评论