本田车系发动机机械参数.doc

本田车系一、发动机匹配表发动机型号匹配车型匹配年款F22A1Accord1993Prelude1993-1996F22B1Accord1994-1997F22B2Accord1994-1997C27A4Accord1995-1997F22A6Accord1993F22B6Odyssey1995-1997F23A1Accord1998-1999F23A4Accord1998-1999F23A5Accord1998-1999F23A7Odyssey1998J30A1Accord1998-1999D15B7Civic1993-1995D15B8Civic1993-1995D15Z1Civic1993-1995D16Y7Civic1996-1999D16Y5Civic1996-1999D16Y8Civic1996-1999D16Z6Civic1993-1995B20B4CR-V1997-1998H22A1Prelude1993-1996H22A4Prelude1997-1999H23A1Prelude1993-19964ZE1Passport1994-19976VD1Passport1994-1999B17A1Integra1993B18A1Integra1993B18B1Integra1994-1997B18C1Integra GS-R1994-1997C32A1Legend1993-1995C32A63.2TL1996-1998C35A13.5RL1996-1998G25A1Vigor1993-1994G25A42.5TL1995-1998二、发动机参数1F22A1、F22A6、F22B1、F22B2型发动机参数表 发动机型号项目F22A1F22A6F22B1F22B2最大功率（Hp/rMin-1）125/5200(DX和LX车型)；140/5600（EX车型）125/5200(DX和LX车型)；140/5600（EX车型）145/5600130/5200最大扭矩(FtLbs/rMin-1)137/4000(DX和LX车型)；142/4500（EX车型）137/4000(DX和LX车型)；142/4500（EX车型）142/4000139/4500缸径行程8595859585958595气缸排量（L）2.22.22.22.2压缩比8.8：18.8：18.8：18.8：1气缸缸径“A”缸或 “”缸标准值85.01-85.0285.01-85.0285.01-85.0285.01-85.02许用极限85.0785.0785.0785.07“B”缸或“”缸标准值85.00-85.0185.00-85.0185.00-85.0185.00-85.01许用极限85.0785.0785.0785.07气缸最大失圆度和锥度0.050.050.050.05气缸最大平面翘曲度标准值0.070.070.070.07许用极限0.100.100.100.10气缸盖高度99.95-100.0599.95-100.0599.95-100.0599.95-100.05气缸盖最大翘曲度0.050.050.050.05气门座宽度进气门标准值1.25-1.551.25-1.551.25-1.551.25-1.55许用极限2.002.002.002.00排气门标准值1.25-1.551.25-1.551.25-1.551.25-1.55许用极限2.002.002.002.00气门座锥角（）45454545气门导管安装后高度进气门23.75-24.2523.75-24.2521.20-22.2023.50-25.50排气门15.05-15.5515.05-15.5520.63-21.6314.80-15.80气门导管内径进气门5.515-5.5305.515-5.5305.515-5.5305.515-5.530排气门5.515-5.5305.515-5.5305.515-5.5305.515-5.530气门杆到导管油隙进气门标准值0.020-0.0450.020-0.0450.02-0.050.02-0.05许用极限0.080.08排气门标准值0.055-0.0800.055-0.0800.05-0.080.05-0.08许用极限0.120.12气门总长进气门110.88-111.18110.88-111.18110.30-110.80107.82-108.32排气门122.15-122.45122.15-122.45108.30-108.50116.95-117.45气门头直径进气门33.90-34.1033.90-34.1033.90-34.1031.90-32.10排气门28.9-29.128.9-29.128.9-29.128.9-29.1气门锥角（）45454545气门最小边缘厚度进气门标准值0.85-1.150.85-1.150.85-1.150.85-1.15许用极限0.650.650.650.65排气门标准值1.05-1.351.05-1.351.05-1.351.05-1.35许用极限0.950.950.950.95气门杆安装后高度进气门标准值48.245-48.71548.245-48.71546.75-47.5548.08-48.88许用极限48.96548.96548.8049.13排气门标准值50.315-50.78550.315-50.78550.15-50.9550.15-50.95许用极限51.03551.03551.2051.20气门杆直径进气门标准值5.485-5.4955.485-5.4955.485-5.4955.485-5.495许用极限5.4555.4555.4555.455排气门标准值5.450-5.4605.450-5.4605.450-5.4605.450-5.460许用极限5.4205.4205.4205.420气门弹簧自由长度进气门51.0853.42（非联合制造）；54.82（联合制造）排气门55.5854.66（非联合制造）；56.28（联合制造）气门间隙进气门0.23-0.280.23-0.280.24-0.280.24-0.28排气门0.28-0.330.28-0.330.28-0.320.28-0.32凸轮轴轴向间隙标准值0.05-0.150.05-0.150.05-0.150.05-0.15许用极限0.500.500.500.50凸轮轴最大径向圆跳动标准值0.0150.0150.030.03许用极限0.0300.0300.040.04油隙标准值0.050-0.0890.050-0.0890.050-0.0890.050-0.089许用极限0.150.150.150.15凸轮轴凸轮高度进气38.52638.74137.775（第一凸轮）；39.725（中间凸轮）；34.481（第二凸轮）38.526排气38.77838.79238.36638.778曲轴轴向间隙标准值0.10-0.350.10-0.350.10-0.350.10-0.35许用极限0.450.450.450.45曲轴圆跳动量标准值0.030.030.030.03许用极限0.040.040.040.04主轴承轴颈直径149.976-50.00049.976-50.00049.984-50.00849.984-50.008249.976-50.00049.976-50.00049.976-50.00049.976-50.000349.972-49.99649.972-49.99649.972-49.99649.972-49.996449.984-50.00849.984-50.00849.984-50.00849.984-50.008549.988-50.01249.988-50.01249.988-50.01249.988-50.012主轴承轴颈失圆度标准值0.0050.0050.0050.005许用极限0.0100.0100.0060.006主轴承轴颈锥度标准值0.0050.0050.0050.005许用极限0.0100.0100.0060.006主轴承油隙1号标准值0.021-0.0450.021-0.0450.013-0.0370.013-0.037许用极限0.050.050.050.052号标准值0.021-0.0450.021-0.0450.021-0.0450.021-0.045许用极限0.050.050.050.053号标准值0.025-0.0490.025-0.0490.025-0.0490.025-0.049许用极限0.050.050.050.054号标准值0.013-0.0370.013-0.0370.013-0.0370.013-0.037许用极限0.050.050.050.055号标准值0.009-0.0330.009-0.0330.009-0.0330.009-0.033许用极限0.050.050.050.05连杆轴承轴颈直径47.976-48.00047.976-48.00047.976-48.00047.976-48.000连杆轴承轴颈失圆度标准值0.0050.0050.0050.005许用极限0.0100.0100.0060.006连杆轴承轴颈锥度标准值0.0050.0050.0050.005许用极限0.0100.0100.0060.006连杆轴承油隙标准值0.021-0.0490.021-0.0490.021-0.0490.021-0.049许用极限0.050.050.050.05连杆大头内径5151连杆销孔孔径标准值21.994-22.00021.994-22.00021.968-21.98121.968-21.981加大尺寸21.997-22.00321.997-22.003活塞销与连杆配合过盈量0.012-0.0320.012-0.0320.013-0.0320.013-0.032曲柄销销孔孔径51.0051.0051.0051.00连杆侧隙标准值0.15-0.300.15-0.300.15-0.300.15-0.30许用极限0.400.400.400.40活塞与气缸间隙标准值0.020-0.0400.020-0.0400.020-0.0400.020-0.040许用极限0.050.050.050.05活塞直径“A”活塞标准值84.980-84.99084.980-84.99084.980-84.99084.980-84.990许用极限84.97084.97084.97084.970“B”活塞标准值84.970-84.98084.970-84.98084.970-84.98084.970-84.980许用极限84.96084.96084.96084.960活塞销直径21.994-22.00021.994-22.00021.994-22.00021.994-22.000活塞配合0.013-0.0230.013-0.0230.010-0.0220.010-0.022连杆配合0.013-0.0320.013-0.0320.013-0.0320.013-0.032活塞环侧隙第一道气环标准值0.036-0.0600.036-0.0600.036-0.0600.036-0.060许用极限0.130.130.130.13第二道气环标准值0.030-0.0550.030-0.0550.030-0.0550.030-0.055许用极限0.130.130.130.13活塞环开口间隙第一道气环标准值0.20-0.350.20-0.350.20-0.350.20-0.35许用极限0.600.600.600.60第二道气环标准值0.40-0.550.40-0.550.40-0.550.40-0.55许用极限0.700.700.700.70油 环标准值0.20-0.70