2路无线控制器百度云产品资料2 CH multi-function Wireless Controller

2 channel multi-function wireless controller Features:1 Operating voltage: DC 9-13V (recommended DC 12V);5V version can be customized2 Operating Current: All relays close, about 14MA; one relay open,about 43MA;two relay open,about 71MA3 Operating frequency: 433.92M; 315M version can be customized 4 Receiver sensitivity : -108dBm5 Decode : learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 16 remote control6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)， Delay;Each channel independently set the Work mode;500,000 seconds maximum delay7 Size(Including housing）75*54*28mm8 Relay Maximum load(Recommended5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDCWork mode Channel 1modeDelay rangeChannel 1modeDelay rangeChannel 1(CH1)Channel 1(CH2)Momentary /Non-locking (Mode 0)0.5 secondsMomentary /Non-locking (Mode 0)0.5 secondsToggle /Self-locking(Mode 1)NonToggle /Self-locking(Mode 1)NonLatch /Inter-locking(Mode 2)NonLatch /Inter-locking(Mode 2)NonDelay 1(Mode 3)0.1-100 SecondsStepper :0.1 SecondsDelay 1(Mode 3)0.1-100 SecondsStepper :0.1 SecondsDelay 2(Mode 4)1-1000 SecondsStepper :1 SecondsDelay 2(Mode 4)1-1000 SecondsStepper :1 SecondsDelay 3(Mode 5)10-10000 SecondsStepper :10 SecondsDelay 3(Mode 5)10-10000 SecondsStepper :10 SecondsDelay 4(Mode 6)100-100000 SStepper :100 SDelay 4(Mode 6)100-100000 SStepper :100 SDelay 5(Mode 7)500-500000 SStepper :500 SDelay 5(Mode 7)500-500000 SStepper :500 SWorking mode user guide : 1: Each Channel have 4 working mode : Delay time , Toggle mode (singnal Self-locking), Momentary Mode ( singnal None-locking) , Latch mode (singnal Inter-locking) . 2: working mode of each channel need to be set individually , 2 channels can have 10 different working mode combinenatoin ,Detail : one channel is Momentary , the other channel is Latch ;one channel is Momentary , the other channel is Momentary ; one channel is Momentary , the other channel is Toggle ;oone channel is Momentary , the other channel is Delay time ;one channel is Toogle , the other channel is Delay Time ;one channel is Toogle , the other channel is Latch ;one channel is Toogle , the other channel is Toggle ;one channel is Latch , the other channel is Delay Time ;one channel is Latch , the other channel is Latch ;one channel is Delay time , the other channel is Delay Time ;3: Time of each delay mode is proportionally increased. For example, you want to channel 1 to delay 50 seconds , 500seconds and 5000 seconds, you can first seting channel 1 is set to delay 1 (Delay Mode 3), turn around (CH1_adj) adjustable resistance, so that channel 1 delay 50 seconds; if the mode is set to delay 2 (mode 4), the delay time becomes 500 seconds, if the mode is set to delay 3 (mode 5), the delay time becomes 5000 seconds4 With a suitable screwdriver and gently rotating adjustable resistance;Clockwise, increasing delay,Counter-clockwise, the delay is reducedGlossary:NO : Relay normally open contactCOM : Relay common contactNC : Relay normally closed contactOpen : NO connection COM, NC disconnect COMClose : NO disconnect COM, NC connection COMMomentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A; the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;Toggle : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as B. Every Channel is Independent ;Latched : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2 is Close. Press transmitter button B, the receiver Channel 2 is Open, the Channel 1 is Close.Delay : Press the Transmitter button A, the receiver Channel 1 is Open,After a set time delay, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent;If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay CloseAdapter remote control (learning remote control):Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashesClean code: press the button and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)Step 1 (into the learning mode): Press the button (about 1 second), LED off;Step 2 (adapter channel 1): Then press the first button on the remote control, LED flashes four times off, then learning the first button valueStep 3 (Adaptation Channel 2): Then press the second button on the remote control, LED flashes four times brighter, then learned two key valuesWiring Diagram:1 DC 12V control circuit,Wiring diagra